Jee-Hun Song
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Jee-Hun Song has a total of 55 co-authors. Here are the top co-authors by number of shared publications:
Suk-Yoon Hong
Department of Naval Architecture and Ocean Engineering, Seoul National University, URL: https://ror.org/04h9pn542
45 shared publicationsHyun-Wung Kwon
Department of Shipbuilding and Marine Engineering, Koje College, Koje, Gyeongsangnam-do, South Korea
27 shared publications- Suk-Yoon Hong
Seoul National University
7 shared publications Han-Shin Seol
6 shared publicationsSang-Jae Yeo
6 shared publications- Woen-Sug Choi
Department of Convergence Study on the Ocean Science and Technology, Korea Maritime and Ocean University, Busan, Korea
6 shared publications
Latest Publications
- 1 June 2026
- Published by Institute of Noise Control Engineering (INCE) in Noise Control Engineering Journal
- Vol. 74 (2) , 199-208
Fully Coupled Electromechanical Model Incorporating Multi-Domain Interactions for Fault Detection in Low-Voltage Squirrel Cage Induction Motors
Low-voltage induction motors are widely used in industry and commercial settings, where reliable operation and early fault detection are crucial to prevent downtime. Past detection methods often rely only on electrical signals, overlooking complex electromechanical interactions that affect fault signatures, especially in vibration signals. This paper introduces a fully coupled electromechanical interaction (F-EMI) model designed for fault detection in low-voltage three-phase squirrel cage induction motors. The model integrates electromagnetic forces, bearing dynamics, and structural deformation to simulate motor behavior under healthy and faulty conditions. The model captures ten key interaction pathways between mechanical and electrical parts and generates realistic fault vibration signals. Validation experiments cover four conditions: healthy, mechanical looseness, stator open-circuit, and bearing outer-race faults. Comparisons of simulated and measured vibration spectra show that the F-EMI model accurately reproduces fault-specific frequencies and broadband levels. These results demonstrate the model’s value for predictive maintenance and fault diagnosis in low-voltage motor applications requiring accurate, system-level interaction modeling.
- 1 June 2026
- Published by Institute of Noise Control Engineering (INCE) in Noise Control Engineering Journal
- Vol. 74 (2) , 199-208
Fully Coupled Electromechanical Model Incorporating Multi-Domain Interactions for Fault Detection in Low-Voltage Squirrel Cage Induction Motors
Low-voltage induction motors are widely used in industry and commercial settings, where reliable operation and early fault detection are crucial to prevent downtime. Past detection methods often rely only on electrical signals, overlooking complex electromechanical interactions that affect fault signatures, especially in vibration signals. This paper introduces a fully coupled electromechanical interaction (F-EMI) model designed for fault detection in low-voltage three-phase squirrel cage induction motors. The model integrates electromagnetic forces, bearing dynamics, and structural deformation to simulate motor behavior under healthy and faulty conditions. The model captures ten key interaction pathways between mechanical and electrical parts and generates realistic fault vibration signals. Validation experiments cover four conditions: healthy, mechanical looseness, stator open-circuit, and bearing outer-race faults. Comparisons of simulated and measured vibration spectra show that the F-EMI model accurately reproduces fault-specific frequencies and broadband levels. These results demonstrate the model’s value for predictive maintenance and fault diagnosis in low-voltage motor applications requiring accurate, system-level interaction modeling.
- 28 February 2026
- Published by The Korean Society of Marine Environment and Safety in Journal of the Korean Society of Marine Environment & Safety
- Vol. 32 (1) , 129-137
Acoustic Performance Characteristics of a Multi-Resonator Broadband Silencer for Offshore Plants
- 28 February 2026
- Published by The Korean Society of Marine Environment and Safety in Journal of the Korean Society of Marine Environment & Safety
- Vol. 32 (1) , 129-137
Acoustic Performance Characteristics of a Multi-Resonator Broadband Silencer for Offshore Plants
- 1 November 2025
- Published by Institute of Noise Control Engineering (INCE) in Noise Control Engineering Journal
- Vol. 73 (4) , 496-505
Model-Based Current Filter Design for Control of Vibrations due to Electric Motor Faults
Excessive vibration caused by motor faults poses significant challenges to system performance and structural stability. This research presents a model-based approach to designing motor current signature filters for effective fault detection and vibration control. The proposed method trains convolution filters exclusively on modeled fault data, leveraging the hypothesis that local minima in the loss function during training on modeled data correspond to those on measured data. Stochastic gradient descent is employed to optimize filter weights and biases, while the minimum redundancy maximum relevance (mRMR) method identifies the most effective filters. Validation on measured data demonstrates the ability of the trained filters to accurately detect and classify various motor states, including healthy conditions, stator open-circuit faults, bearing outer-race faults, and mechanical looseness. By enabling precise fault detection, the designed filters facilitate targeted vibration control, reducing fault-induced vibrations and enhancing system reliability. This model-based approach offers a cost-effective and efficient solution for fault diagnosis and vibration management, advancing the field of noise and vibration engineering.
- 1 November 2025
- Published by Institute of Noise Control Engineering (INCE) in Noise Control Engineering Journal
- Vol. 73 (4) , 496-505
Model-Based Current Filter Design for Control of Vibrations due to Electric Motor Faults
Excessive vibration caused by motor faults poses significant challenges to system performance and structural stability. This research presents a model-based approach to designing motor current signature filters for effective fault detection and vibration control. The proposed method trains convolution filters exclusively on modeled fault data, leveraging the hypothesis that local minima in the loss function during training on modeled data correspond to those on measured data. Stochastic gradient descent is employed to optimize filter weights and biases, while the minimum redundancy maximum relevance (mRMR) method identifies the most effective filters. Validation on measured data demonstrates the ability of the trained filters to accurately detect and classify various motor states, including healthy conditions, stator open-circuit faults, bearing outer-race faults, and mechanical looseness. By enabling precise fault detection, the designed filters facilitate targeted vibration control, reducing fault-induced vibrations and enhancing system reliability. This model-based approach offers a cost-effective and efficient solution for fault diagnosis and vibration management, advancing the field of noise and vibration engineering.
- 28 February 2025
- Published by The Korean Society of Marine Environment and Safety in Journal of the Korean Society of Marine Environment & Safety
- Vol. 31 (1) , 172-179
Development of Marine Propulsion Motor Analysis Method for Fault Detections
- 28 February 2025
- Published by The Korean Society of Marine Environment and Safety in Journal of the Korean Society of Marine Environment & Safety
- Vol. 31 (1) , 172-179
Development of Marine Propulsion Motor Analysis Method for Fault Detections
- 14 September 2024
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part M: Journal of Engineering for the Maritime Environment
- Vol. 239 (2) , 301-312
Effect of pre-swirl stator angles on broadband noise considering hydrodynamic performance of pump-jet propeller
A pump-jet propeller is composed of a rotor, stator, and duct. A pre-swirl stator is employed to optimize flow into the rotor. The hydrodynamic and noise performances of pump-jet propellers vary with the stator angles. In this study, the hydrodynamic performance of a full-scale submarine and pump-jet propeller is assessed by conducting computational fluid dynamics simulations based on the Reynolds-averaged Navier–Stokes equation. Additionally, broadband noise, blade-passing frequency noise, and a significant factor, that is, underwater radiated noise are predicted using Lighthill’s equation, Green’s function, and wall pressure spectrum. Unsteady forces were extracted from the flow field to obtain the blade-passing frequency noise. Broadband noise could not be calculated directly from the flow field owing to the absence of small eddies, and wall pressure spectrum was used to obtain high-frequency broadband noise. The overall noise, including broadband noise and blade-passing frequency noise, was evaluated. The optimal stator angle for the rotor at the self-propulsion point was determined considering the propulsion efficiency and noise level of the pump-jet propeller.
- 14 September 2024
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part M: Journal of Engineering for the Maritime Environment
- Vol. 239 (2) , 301-312
Effect of pre-swirl stator angles on broadband noise considering hydrodynamic performance of pump-jet propeller
A pump-jet propeller is composed of a rotor, stator, and duct. A pre-swirl stator is employed to optimize flow into the rotor. The hydrodynamic and noise performances of pump-jet propellers vary with the stator angles. In this study, the hydrodynamic performance of a full-scale submarine and pump-jet propeller is assessed by conducting computational fluid dynamics simulations based on the Reynolds-averaged Navier–Stokes equation. Additionally, broadband noise, blade-passing frequency noise, and a significant factor, that is, underwater radiated noise are predicted using Lighthill’s equation, Green’s function, and wall pressure spectrum. Unsteady forces were extracted from the flow field to obtain the blade-passing frequency noise. Broadband noise could not be calculated directly from the flow field owing to the absence of small eddies, and wall pressure spectrum was used to obtain high-frequency broadband noise. The overall noise, including broadband noise and blade-passing frequency noise, was evaluated. The optimal stator angle for the rotor at the self-propulsion point was determined considering the propulsion efficiency and noise level of the pump-jet propeller.
- 30 August 2024
- Published by Elsevier in Computers & Mathematics with Applications
- Vol. 174, 142-150
Direct hydroacoustics analyses of pipe orifice using lattice Boltzmann method
- 30 August 2024
- Published by Elsevier in Computers & Mathematics with Applications
- Vol. 174, 142-150
Direct hydroacoustics analyses of pipe orifice using lattice Boltzmann method
- Open Access
- 12 June 2024
- Published by Elsevier in International Journal of Naval Architecture and Ocean Engineering
- Vol. 16
Numerical study on the distance between the propeller with pre-swirl duct and rudder considering fatigue characteristics
- 12 June 2024
- Published by Elsevier in International Journal of Naval Architecture and Ocean Engineering
- Vol. 16
Open AccessNumerical study on the distance between the propeller with pre-swirl duct and rudder considering fatigue characteristics
- 10 May 2024
- Published by SAGE Publications in Journal of Vibration and Control
- Vol. 31 (9-10) , 1936-1952
A study of multi-acoustic black holes considering suitability of attachment positions for suppressing low-frequency vibrations on large motor
Vibrations generated from machinery in various industries, such as the automotive, aerospace, and shipbuilding industries, must be suppressed for developing low-vibration and low-noise systems. High-frequency vibrations can be easily controlled via damping treatments; however, controlling vibrations in the low-frequency range generated from large machinery is a major challenge. In general, a substantial amount of damping material is required for suppressing low-frequency vibrations. This is unsuitable when developing low-cost, lightweight, and eco-friendly systems. To overcome the limitations, effective methods are required for suppressing these low-frequency vibrations. In this study, an effective method was proposed for suppressing vibrations in the low-frequency range using multiple acoustic black holes (multi-ABHs) considering the suitability values of the attachment positions, which were determined by flexural wave propagation and interactions between the multi-ABHs and structures. The suitability values of the attachment positions are proposed as non-dimensional parameters that are calculated using the structural intensity and mode superposition methods. For validating the proposed method, the vibration suppression characteristics were analyzed using a steel plate. The analyzed cases were categorized into six groups according to the suitability values of the attachment positions of the multi-ABHs. The largest reduction in vibrations was observed when the multi-ABHs were attached to the location with the highest suitability in the six cases. Finally, the multi-ABHs were applied to a large 2-pole motor considering the suitability values of the attachment positions, and the dominant vibrations at 60, 120, and 180 Hz frequencies were suppressed.
- 10 May 2024
- Published by SAGE Publications in Journal of Vibration and Control
- Vol. 31 (9-10) , 1936-1952
A study of multi-acoustic black holes considering suitability of attachment positions for suppressing low-frequency vibrations on large motor
Vibrations generated from machinery in various industries, such as the automotive, aerospace, and shipbuilding industries, must be suppressed for developing low-vibration and low-noise systems. High-frequency vibrations can be easily controlled via damping treatments; however, controlling vibrations in the low-frequency range generated from large machinery is a major challenge. In general, a substantial amount of damping material is required for suppressing low-frequency vibrations. This is unsuitable when developing low-cost, lightweight, and eco-friendly systems. To overcome the limitations, effective methods are required for suppressing these low-frequency vibrations. In this study, an effective method was proposed for suppressing vibrations in the low-frequency range using multiple acoustic black holes (multi-ABHs) considering the suitability values of the attachment positions, which were determined by flexural wave propagation and interactions between the multi-ABHs and structures. The suitability values of the attachment positions are proposed as non-dimensional parameters that are calculated using the structural intensity and mode superposition methods. For validating the proposed method, the vibration suppression characteristics were analyzed using a steel plate. The analyzed cases were categorized into six groups according to the suitability values of the attachment positions of the multi-ABHs. The largest reduction in vibrations was observed when the multi-ABHs were attached to the location with the highest suitability in the six cases. Finally, the multi-ABHs were applied to a large 2-pole motor considering the suitability values of the attachment positions, and the dominant vibrations at 60, 120, and 180 Hz frequencies were suppressed.
- Open Access
- 6 May 2024
- Published by Elsevier in International Journal of Naval Architecture and Ocean Engineering
- Vol. 16
Deep-reinforcement-learning-based hull form optimization method for stealth submarine design
- 6 May 2024
- Published by Elsevier in International Journal of Naval Architecture and Ocean Engineering
- Vol. 16
Open AccessDeep-reinforcement-learning-based hull form optimization method for stealth submarine design
- 30 April 2024
- Published by The Korean Society of Marine Environment and Safety in Journal of the Korean Society of Marine Environment & Safety
- Vol. 30 (2) , 252-261
Research on the Design Methods of Appendages to Reduce Vortex Flows Around Underwater Vehicles
- 30 April 2024
- Published by The Korean Society of Marine Environment and Safety in Journal of the Korean Society of Marine Environment & Safety
- Vol. 30 (2) , 252-261
Research on the Design Methods of Appendages to Reduce Vortex Flows Around Underwater Vehicles