Jing Wei

Carbon neutrality and green energy development are global priorities, with wind energy occupying a prominent position in the green power structure. However, wind turbine failures and economic losses have attracted increasing industry attention, leading to more research on wind turbine dynamic characteristics. While many scholars have focused on torsional vibration research and used passive control methods for vibration reduction, this paper proposes an active control method combining variable structure sliding mode control and model predictive control with harmonic suppression. We establish a coupled model of the electromechanical drive chain control system of a large semi-direct drive wind turbine, including subsystems such as the gear set, power system, and control system. Our goal is to reduce wind turbine vibration response. To evaluate the effectiveness of the new control strategy on reducing drive chain vibration and improving generator dynamic response, we analyze the vibration response of the main drive chain components, generator current, electromagnetic torque, and rotor speed response. The results demonstrate that the new control strategy effectively improves the dynamic response of the generator and reduces drive chain vibration.

This study first assessed the friction and wear properties of two polytetrafluoroethylene materials sliding against electroplated chrome and high-velocity oxy-fuel-sprayed WC-10Co-4Cr coatings. Subsequently, the sealing performance of three different structure seals made from these two polytetrafluoroethylene materials was investigated on both electroplated chrome and high-velocity oxy-fuel-sprayed WC-10Co-4Cr coatings. The study results indicate the following: in terms of changes in the counter-face surface roughness, both the electroplated chrome and high-velocity oxy-fuel-sprayed WC-10Co-4Cr surfaces exhibited an increase in surface roughness after sliding, demonstrating the phenomenon of “soft material wearing hard material.” Moreover, the changes in surface roughness were greater after sliding against wollastonite mineral-filled polytetrafluoroethylene than against polyether ether ketone-filled polytetrafluoroethylene, indicating that wollastonite mineral-filled polytetrafluoroethylene was more likely to cause damage to the metal surface. Regarding the friction coefficient and wear amount, under dry friction conditions, both materials exhibited higher friction coefficients but lower wear rates on high-velocity oxy-fuel-sprayed WC-10Co-4Cr surfaces, while showing lower friction coefficients but higher wear rates on electroplated chrome surfaces. This behavior was related to the ease of transfer film formation and the stability of the transfer films formed by polytetrafluoroethylene materials on the two surfaces. In terms of the products’ sealing performance, test results showed that, for composite seals with polytetrafluoroethylene as the counter-face, sealing performance was better on high-velocity oxy-fuel-sprayed WC-10Co-4Cr surfaces than on electroplated chrome surfaces. For seals with rubber as the counter-face, there was little difference in sealing performance between high-velocity oxy-fuel-sprayed WC-10Co-4Cr and electroplated chrome surfaces.

The traction behavior in cryogenic solid-lubricated ball bearings (CSLBBs) used in liquid rocket engines (LREs) affects not only the dynamic response of the bearing but also the lubricity and wear characteristics of the solid lubrication coating. The traction coefficient between the ball and raceway depends on factors such as contact material, relative sliding velocity, and contact pressure. However, existing traction curve models for CSLBBs typically consider only one or two of these factors, limiting the accuracy and applicability of theoretical predictions. In this study, a novel traction model for CSLBBs is proposed, which incorporates the combined effects of contact material, relative sliding velocity, and contact pressure. Based on this model, a tribo-dynamic framework is developed to investigate the tribological and dynamic behavior of CSLBBs. The model is validated through both theoretical analysis and experimental data. Results show that the inclusion of solid lubricant effects significantly alters the relative sliding and frictional forces between the rolling elements and the raceway. These changes in turn influence the impact dynamics between the rolling elements and the cage, leading to notable variations in the bearing’s vibrational response. The findings may offer valuable insights for the wear resistance and vibration reduction design of CSLBBs.

Solid-lubricated rolling bearings are widely used in the aerospace field and are key components to support spacecraft rotors. During the start-up of the engine, the sharp acceleration may cause bearing skidding, resulting in damage of the solid lubricating film and a reduction in the remaining useful life of the bearing. However, the existing research on the tribo-dynamic responses of solid-lubricated ball bearings mostly relies on semi-empirical tribological models, which are limited in their ability to reveal the micro–macro sliding mechanisms of the ball–raceway contact interface. In this paper, a novel tribo-dynamic model for solid-lubricated angular contact ball bearings is developed by applying Kalker’s rolling contact theory to the Gupta dynamic model. The interpolation method is adopted to calculate contact parameters to improve the model’s efficiency. Using the proposed model, the dynamic response of the bearing in the acceleration process is studied, and the mechanism and influence characteristics of skidding, over-skidding, and creepage of the rolling element are analyzed. The results show that the main reason for skidding is that the traction force is not enough to overcome the resistance, and the gyroscopic effect is the main cause of over-skidding, which follows the principle of conservation of the angular momentum of the ball.

High-speed trains typically utilize helical gear transmissions, which significantly impact the bearing load capacity and fatigue service performance of the gearbox bearings. This paper focuses on the gearbox bearings, establishing dynamic models for both helical gear and herringbone gear transmissions in high-speed trains. The modeling particularly emphasizes the precision of the bearings at the gearbox’s pinion and gear wheels. Using this model, a comparative analysis is conducted on the bearing loads and contact stresses of the gearbox bearings under uniform-speed operation between the two gear transmissions. The findings reveal that the helical gear transmission generates axial forces leading to severe load imbalance on the bearings at both sides of the large gear, and this imbalance intensifies with the increase in train speed. Consequently, this results in a significant increase in contact stress on the bearings on one side. The adoption of herringbone gear transmission effectively suppresses axial forces, resolving the load imbalance issue and substantially reducing the contact stress on the originally biased side of the bearings. The study demonstrates that employing herringbone gear transmission can significantly enhance the service performance of high-speed train gearbox bearings, thereby extending their service life.

The tilting-pad journal bearing in the cooling system of the nuclear power plant is equipped below the ground and vertically positioned to accomplish its function for water transfer. Usually, the loading conditions are relatively stable since the required water volume almost remains the same level during the operation, but the loading direction cannot be known in advance. Furthermore, the bearing is designed with several separate pads, which allows the bearing to support the loading flexibly. The safety application of nuclear energy requires the bearing to have a reliable ability to maintain the rotating motion of gear sets. This study develops a numerical model to simulate the mixed thermo-elastohydrodynamic lubrication for the tilting-pad journal bearing in the nuclear plant. The elastic and thermal fields are properly determined, and the induced displacement is taken into account for an accurate description of film thickness. The asperity contact due to misaligned journal is well evaluated in the local area where the lubrication film cannot separate the surfaces. A parametric study is undertaken in detail to reveal the aspects that influence bearing lubrication. The conclusions potentially provide fundamentals for further lubrication optimization of the bearing system.