Avwerosuoghene Moses Okoro
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Avwerosuoghene Moses Okoro has a total of 47 co-authors. Here are the top co-authors by number of shared publications:
Peter Apata Olubambi
Centre for Nanomechanics and Tribocorrosion, Department of Metallurgy, School of Mining, Metallurgy and Chemical Engineering, University of Johannesburg, Republic of South Africa
8 shared publications- Peter Apata Olubambi
University of Johannesburg
7 shared publications - Ronald Machaka
Council for Scientific and Industrial Research, Pretoria, South Africa
7 shared publications Senzeni Sipho Lephuthing
Centre for Nanomechanics and Tribocorrosion, Department of Metallurgy, School of Mining, Metallurgy and Chemical Engineering, University of Johannesburg, Republic of South Africa
7 shared publicationsSamuel Ranti Oke
Centre for Nanomechanics and Tribocorrosion, Department of Metallurgy, School of Mining, Metallurgy and Chemical Engineering, University of Johannesburg, Republic of South Africa
6 shared publicationsMary Ajimegoh Awotunde
Centre for Nanoengineering and Tribocorrosion, Department of Metallurgy, School of Mining, Metallurgy and Chemical Engineering, University of Johannesburg, Johannesburg, Republic of South Africa
5 shared publications
Latest Publications
- Open Access
- 1 January 2026
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2026 (1) , 8536362
Spark Plasma Sintering of Low‐Density Stainless Steel: Optimisation of Sintering Parameters
The study was conducted to determine the optimised sintering conditions for producing low‐density stainless steel via powder metallurgy route. Low‐density Fe–Mn–Al–Cr–C stainless‐steel alloys containing Mo and Cu were produced from commercially available elemental powders via mechanical alloying followed by consolidation using spark plasma sintering (SPS). Four alloy compositions under varying sintering parameters, including temperature (900°C–1100°C), dwell time (5–7 min) and pressure (40–50 MPa), were explored. Electrochemical testing, including open‐circuit potential (OCP) and cyclic polarisation (CP), was performed in 0.9% NaCl to evaluate corrosion susceptibility. Characterisation of both the mechanically alloyed powders and the sintered alloys was performed using scanning electron microscopy–backscattered electron imaging, scanning electron microscopy–energy‐dispersive X‐ray spectroscopy and X‐ray diffraction. The XRD patterns of the mechanically alloyed powders revealed the presence of two phases, austenite and ferrite, together with the formation of Mo‐enriched precipitates. Results indicated that sintering temperature, pressure and dwell time had a significant effect on the final density, which increased with higher parameter values. The sintered alloys achieved relative densities between approximately 94% and 100%. The porosity ranged from 0.01% to 5%. Microstructural examination indicated that the alloys consist mainly of a duplex configuration made up of γ ‐austenite with an FCC crystal structure and α ‐ferrite with a BCC structure. In addition, precipitates enriched in Cr and Mo were identified particularly in Alloys 3 (Fe–30.67Mn–2.39Al–4.23Cr–0.09C–5.20Mo–3.44Cu wt%) and 4 (Fe–21.55Mn–3.78Al–4.12Cr–0.22C–5.30Mo–3.51Cu wt%). Among all compositions, Alloy 1 (6Fe‐31.49 Mn‐2.45 Al‐4.34 Cr‐0.09 C wt%) demonstrated the best overall sintering response, microstructural quality and corrosion resistance, achieving a high density of 99.4% (Alloy 1C) and a low corrosion rate of 0.087 mm/yr (Alloy 1D). The optimum sintering conditions were determined to be 1100°C and 50 MPa for Alloys 1 (Fe‐31.49Mn‐2.45Al‐4.34Cr‐0.09C wt%) and 2 (Fe‐22.14Mn‐3.88Al‐4.23Cr‐0.23C wt%) and 900°C and 50 MPa for Alloys 3 (Fe‐30.67Mn‐2.39Al‐4.23Cr‐0.09C‐5.20Mo‐3.44Cu wt%) and 4 (Fe‐21.55Mn‐3.78Al‐4.12Cr‐0.22C‐5.30Mo‐3.51Cu wt%).
- 1 January 2026
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2026 (1) , 8536362
Open AccessSpark Plasma Sintering of Low‐Density Stainless Steel: Optimisation of Sintering Parameters
The study was conducted to determine the optimised sintering conditions for producing low‐density stainless steel via powder metallurgy route. Low‐density Fe–Mn–Al–Cr–C stainless‐steel alloys containing Mo and Cu were produced from commercially available elemental powders via mechanical alloying followed by consolidation using spark plasma sintering (SPS). Four alloy compositions under varying sintering parameters, including temperature (900°C–1100°C), dwell time (5–7 min) and pressure (40–50 MPa), were explored. Electrochemical testing, including open‐circuit potential (OCP) and cyclic polarisation (CP), was performed in 0.9% NaCl to evaluate corrosion susceptibility. Characterisation of both the mechanically alloyed powders and the sintered alloys was performed using scanning electron microscopy–backscattered electron imaging, scanning electron microscopy–energy‐dispersive X‐ray spectroscopy and X‐ray diffraction. The XRD patterns of the mechanically alloyed powders revealed the presence of two phases, austenite and ferrite, together with the formation of Mo‐enriched precipitates. Results indicated that sintering temperature, pressure and dwell time had a significant effect on the final density, which increased with higher parameter values. The sintered alloys achieved relative densities between approximately 94% and 100%. The porosity ranged from 0.01% to 5%. Microstructural examination indicated that the alloys consist mainly of a duplex configuration made up of γ ‐austenite with an FCC crystal structure and α ‐ferrite with a BCC structure. In addition, precipitates enriched in Cr and Mo were identified particularly in Alloys 3 (Fe–30.67Mn–2.39Al–4.23Cr–0.09C–5.20Mo–3.44Cu wt%) and 4 (Fe–21.55Mn–3.78Al–4.12Cr–0.22C–5.30Mo–3.51Cu wt%). Among all compositions, Alloy 1 (6Fe‐31.49 Mn‐2.45 Al‐4.34 Cr‐0.09 C wt%) demonstrated the best overall sintering response, microstructural quality and corrosion resistance, achieving a high density of 99.4% (Alloy 1C) and a low corrosion rate of 0.087 mm/yr (Alloy 1D). The optimum sintering conditions were determined to be 1100°C and 50 MPa for Alloys 1 (Fe‐31.49Mn‐2.45Al‐4.34Cr‐0.09C wt%) and 2 (Fe‐22.14Mn‐3.88Al‐4.23Cr‐0.23C wt%) and 900°C and 50 MPa for Alloys 3 (Fe‐30.67Mn‐2.39Al‐4.23Cr‐0.09C‐5.20Mo‐3.44Cu wt%) and 4 (Fe‐21.55Mn‐3.78Al‐4.12Cr‐0.22C‐5.30Mo‐3.51Cu wt%).
- Open Access
- 30 March 2021
- Published by EDP Sciences in Manufacturing Review
- Vol. 8, 9
Influence of aluminium content on the microstructure and densification of spark plasma sintered nickel aluminium bronze
In this study, nickel aluminium bronze alloys (NAB) with appreciable densification and improved microhardness was consolidated via spark plasma sintering technique. The NAB alloy was synthesized from starting elemental powders comprised nickel (4 wt.%), aluminium (6, 8 & 10 wt.%) and copper using dry milling technique. Starting powders were homogeneously milled using gentle ball mill for 8 h at a speed of 150 rpm and a BPR of 10:1. Subsequently, the milled powders were consolidated using the spark plasma sintering technique at 750 degrees C under a compressive pressure of 50 MPa and rate of heating (100 degrees C/min). Furthermore, the powders and sintered alloys were characterized using SEM and XRD to ascertain the microstructural and phase evolutions during the synthesis of the NAB. The density and microhardness of the alloys were further investigated to ascertain the integrity of the sintered alloys. The results indicated that the increase in aluminium content resulted in the formation of intermetallic and beta phases on the alloy after sintering and the microhardness of the alloys improved with the increase in aluminium content.
- 30 March 2021
- Published by EDP Sciences in Manufacturing Review
- Vol. 8, 9
Open AccessInfluence of aluminium content on the microstructure and densification of spark plasma sintered nickel aluminium bronze
In this study, nickel aluminium bronze alloys (NAB) with appreciable densification and improved microhardness was consolidated via spark plasma sintering technique. The NAB alloy was synthesized from starting elemental powders comprised nickel (4 wt.%), aluminium (6, 8 & 10 wt.%) and copper using dry milling technique. Starting powders were homogeneously milled using gentle ball mill for 8 h at a speed of 150 rpm and a BPR of 10:1. Subsequently, the milled powders were consolidated using the spark plasma sintering technique at 750 degrees C under a compressive pressure of 50 MPa and rate of heating (100 degrees C/min). Furthermore, the powders and sintered alloys were characterized using SEM and XRD to ascertain the microstructural and phase evolutions during the synthesis of the NAB. The density and microhardness of the alloys were further investigated to ascertain the integrity of the sintered alloys. The results indicated that the increase in aluminium content resulted in the formation of intermetallic and beta phases on the alloy after sintering and the microhardness of the alloys improved with the increase in aluminium content.
- 20 August 2020
- Published by Springer Nature
- p. 135-143
Effect of Multi-walled Carbon Nanotubes Additions on Its Dispersion Characteristics in Titanium Oxides
- 20 August 2020
- Published by Springer Nature
- p. 135-143
Effect of Multi-walled Carbon Nanotubes Additions on Its Dispersion Characteristics in Titanium Oxides
- Open Access
- 22 June 2020
- Published by Springer Nature in Metals and Materials International
- Vol. 27 (11) , 4869-4885
Microstructural Evolution and Mechanical Properties of Multiwall Carbon Nanotubes Reinforced Titanium-Based Nanocomposites Developed by Spark Plasma Sintering
- 22 June 2020
- Published by Springer Nature in Metals and Materials International
- Vol. 27 (11) , 4869-4885
Open AccessMicrostructural Evolution and Mechanical Properties of Multiwall Carbon Nanotubes Reinforced Titanium-Based Nanocomposites Developed by Spark Plasma Sintering
- 1 January 2020
- Published by Elsevier in Materials Today: Proceedings
- Vol. 28, 615-619
Influence of carbon nanotubes addition on the mechanical properties of nickel aluminide – NiAl
- 1 January 2020
- Published by Elsevier in Materials Today: Proceedings
- Vol. 28, 615-619
Influence of carbon nanotubes addition on the mechanical properties of nickel aluminide – NiAl
- 1 January 2020
- Published by Elsevier in Materials Today: Proceedings
- Vol. 28, 704-709
Comparison of dispersion methods of multi-walled carbon nanotubes in titanium oxide
- 1 January 2020
- Published by Elsevier in Materials Today: Proceedings
- Vol. 28, 704-709
Comparison of dispersion methods of multi-walled carbon nanotubes in titanium oxide
- 1 January 2020
- Published by Elsevier in Materials Today: Proceedings
- Vol. 28, 625-629
Effects of carbon nanotube weight fraction on the fracture toughness of spark plasma sintered nickel aluminide-NiAl3
- 1 January 2020
- Published by Elsevier in Materials Today: Proceedings
- Vol. 28, 625-629
Effects of carbon nanotube weight fraction on the fracture toughness of spark plasma sintered nickel aluminide-NiAl3
- 1 January 2020
- Published by Elsevier in Materials Today: Proceedings
- Vol. 28, 450-454
Densification behaviour of spark plasma sintered multiwall carbon nanotubes reinforced Ti6Al4V nanocomposites
- 1 January 2020
- Published by Elsevier in Materials Today: Proceedings
- Vol. 28, 450-454
Densification behaviour of spark plasma sintered multiwall carbon nanotubes reinforced Ti6Al4V nanocomposites
- 26 November 2019
- Published by Elsevier in Materials Today: Proceedings
- Vol. 18, 3791-3797
Dispersion characteristics, microstructural evolution and sintering behaviour of Al2O3-Ti6Al4V composites fabricated by spark plasma sintering
- 26 November 2019
- Published by Elsevier in Materials Today: Proceedings
- Vol. 18, 3791-3797
Dispersion characteristics, microstructural evolution and sintering behaviour of Al2O3-Ti6Al4V composites fabricated by spark plasma sintering