Aleksey N. Shapovalov
Research Subjects
Aleksey N. Shapovalov has a total of 44 co-authors. Here are the top co-authors by number of shared publications:
- Roman. R. Dema
Nosov Magnitogorsk State Technical University, Magnitogorsk, Russia
9 shared publications E. V. Ovchinnikova
National University of Science and Technology “MISIS” (MISIS)
4 shared publicationsN. A. Maistrenko
Ural Steel
3 shared publicationsV. B. Gorbunov
National University of Science and Technology “MISIS” (MISIS)
3 shared publicationsA. M. Stolyarov
Nosov Magnitogorsk State Technical University
2 shared publicationsA. N. Kalitaev
Nosov Magnitogorsk State Technical University
2 shared publications
Latest Publications
- Open Access
- 30 June 2025
- Published by Siberian State Industrial University in Bulletin of the Siberian State Industrial University
- Vol. 1 (2) , 52-61
INFLUENCE OF STEELMAKING PARAMETERS ON THE REFRACTORY LINING LIFE
ВЛИЯНИЕ ПАРАМЕТРОВ ВЫПЛАВКИ СТАЛИ НА СТОЙКОСТЬ ОГНЕУПОРНОЙ ФУТЕРОВКИ
- 30 June 2025
- Published by Siberian State Industrial University in Bulletin of the Siberian State Industrial University
- Vol. 1 (2) , 52-61
Open AccessINFLUENCE OF STEELMAKING PARAMETERS ON THE REFRACTORY LINING LIFE
ВЛИЯНИЕ ПАРАМЕТРОВ ВЫПЛАВКИ СТАЛИ НА СТОЙКОСТЬ ОГНЕУПОРНОЙ ФУТЕРОВКИ
- 13 December 2024
- Published by Ore and Metals Publishing House in CIS Iron and Steel Review
- Vol. 28, 15-20
The influence of parameters of slag conditions on blast furnace smelting performance and cast iron quality
- 13 December 2024
- Published by Ore and Metals Publishing House in CIS Iron and Steel Review
- Vol. 28, 15-20
The influence of parameters of slag conditions on blast furnace smelting performance and cast iron quality
- Open Access
- 1 March 2023
- Published by National University of Science and Technology MISiS in Izvestiya. Ferrous Metallurgy
- Vol. 66 (1) , 97-104
Impact of barium and strontium on calcium recovery level in ladle treatment of steel by complex modifiers with alkaline-earth metals
Increasingly rigid requirements in terms of the steel products quality are forcing the technical experts of metallurgical production to look for new solutions to stabilize the steel quality. Much attention is paid to ladle treatment technologies and selection well-minded composition of modifiers, which makes it possible to reduce steel contamination by non-metallic inclusions. To solve this problem, complex modifiers containing both calcium and other alkaline-earth metals (barium and strontium) are used. The paper presents the results of the pilot scale tests of steel ladle treatment by complex modifiers with alkaline-earth metals (Si, Ca, Ba) in steel production with increased requirements to non-metallic inclusions in conditions of electric furnace steelmaking shop of JSC “Ural Steel”. During experimental work it was possible to reduce the maximum contamination score profile rolled steel from pipe steel grades for brittle silicates (GOST 1778) from 4.0 to 1.5 – 2.5, for non-deforming silicates from 4.0 to 3.0 – 3.5. The substitution of SK40 grade silicocalcium for experimental modifiers led to an improvement in the strength properties of rolled products, both in tensile tests and in impact bending tests at low temperatures. The indicated impact was observed in all variants of consumption the experimental master alloys. It is noted that with an increasing in the consumption of master alloys, the positive effect on the steel mechanical properties enhanced. It was established that the replacement of silicocalcium with experimental variants of master alloys made it possible to increase the calcium recovery by an average of 1.6 times when using Si – Ca – Ba, and by an average of 2.4 times when using Si – Ca – Ba – Sr. The use of complex modifiers made it possible to obtain the target value of residual calcium in the sample at significantly lower calcium consumption.
- 1 March 2023
- Published by National University of Science and Technology MISiS in Izvestiya. Ferrous Metallurgy
- Vol. 66 (1) , 97-104
Open AccessImpact of barium and strontium on calcium recovery level in ladle treatment of steel by complex modifiers with alkaline-earth metals
Increasingly rigid requirements in terms of the steel products quality are forcing the technical experts of metallurgical production to look for new solutions to stabilize the steel quality. Much attention is paid to ladle treatment technologies and selection well-minded composition of modifiers, which makes it possible to reduce steel contamination by non-metallic inclusions. To solve this problem, complex modifiers containing both calcium and other alkaline-earth metals (barium and strontium) are used. The paper presents the results of the pilot scale tests of steel ladle treatment by complex modifiers with alkaline-earth metals (Si, Ca, Ba) in steel production with increased requirements to non-metallic inclusions in conditions of electric furnace steelmaking shop of JSC “Ural Steel”. During experimental work it was possible to reduce the maximum contamination score profile rolled steel from pipe steel grades for brittle silicates (GOST 1778) from 4.0 to 1.5 – 2.5, for non-deforming silicates from 4.0 to 3.0 – 3.5. The substitution of SK40 grade silicocalcium for experimental modifiers led to an improvement in the strength properties of rolled products, both in tensile tests and in impact bending tests at low temperatures. The indicated impact was observed in all variants of consumption the experimental master alloys. It is noted that with an increasing in the consumption of master alloys, the positive effect on the steel mechanical properties enhanced. It was established that the replacement of silicocalcium with experimental variants of master alloys made it possible to increase the calcium recovery by an average of 1.6 times when using Si – Ca – Ba, and by an average of 2.4 times when using Si – Ca – Ba – Sr. The use of complex modifiers made it possible to obtain the target value of residual calcium in the sample at significantly lower calcium consumption.
- 29 December 2021
- Published by Ore and Metals Publishing House in CIS Iron and Steel Review
- Vol. 22, 15-19
Improvement of the secondary cooling mode for continuous casting of round billets at Ural Steel JSC
Formation of hot cracks on continuously cast round billets is the frequent problem in metallurgical production. The article presents the results of a study of the macrostructure, surface quality and technology of continuous casting of round billets with a diameter of 455 mm, produced at the bloom caster of Ural Steel JSC. The main defects of such billets are identified as surface cracks of “combined” type, namely, transverse cracks (the share among the billets with defects is 9.1%), cracks of the mesh form (the share among the billets with defects is 8.3%). The main reasons for the unsatisfactory quality of the ingot are determined: increased overheating of metal in the tundish, which can be partially compensated by reduction of the casting speed, and intensive cooling of billet surface in the first segments of secondary cooling, which increase thermal stresses in metal with consequent heating of surface layers. It was decided that the most effective way to minimize billet defects is to improve the secondary cooling technology in compliance with the regulated casting temperature and speed procedure. Thermal calculations of billet solidification are conducted. It was revealed that overcooling of billet surface occurs in the first segments of secondary cooling under the existing secondary cooling modes and temperature and speed modes of casting, which leads to additional thermal and phase stresses. In the third segment of the secondary cooling zone, heating of the billet surface is observed due to the heat of the central part. Rational flow rates of cooling agent for the secondary cooling segments of the bloom continuous casting machine are proposed. They include expansion of the active section of secondary cooling with a reduction of cooling agent consumption in the first segments will reduce the thermal cycling processes in the hardened crust and minimize the likelihood of cracking. The work was conducted under financial support of the RF Ministry of Science and High Education (project No. FZRU-2020-0011).
- 29 December 2021
- Published by Ore and Metals Publishing House in CIS Iron and Steel Review
- Vol. 22, 15-19
Improvement of the secondary cooling mode for continuous casting of round billets at Ural Steel JSC
Formation of hot cracks on continuously cast round billets is the frequent problem in metallurgical production. The article presents the results of a study of the macrostructure, surface quality and technology of continuous casting of round billets with a diameter of 455 mm, produced at the bloom caster of Ural Steel JSC. The main defects of such billets are identified as surface cracks of “combined” type, namely, transverse cracks (the share among the billets with defects is 9.1%), cracks of the mesh form (the share among the billets with defects is 8.3%). The main reasons for the unsatisfactory quality of the ingot are determined: increased overheating of metal in the tundish, which can be partially compensated by reduction of the casting speed, and intensive cooling of billet surface in the first segments of secondary cooling, which increase thermal stresses in metal with consequent heating of surface layers. It was decided that the most effective way to minimize billet defects is to improve the secondary cooling technology in compliance with the regulated casting temperature and speed procedure. Thermal calculations of billet solidification are conducted. It was revealed that overcooling of billet surface occurs in the first segments of secondary cooling under the existing secondary cooling modes and temperature and speed modes of casting, which leads to additional thermal and phase stresses. In the third segment of the secondary cooling zone, heating of the billet surface is observed due to the heat of the central part. Rational flow rates of cooling agent for the secondary cooling segments of the bloom continuous casting machine are proposed. They include expansion of the active section of secondary cooling with a reduction of cooling agent consumption in the first segments will reduce the thermal cycling processes in the hardened crust and minimize the likelihood of cracking. The work was conducted under financial support of the RF Ministry of Science and High Education (project No. FZRU-2020-0011).
- 15 September 2019
- Published by Publishing Center Science and Practice in Bulletin of Science and Practice
- Vol. 5 (9) , 262-269
Quality Assessment of Metal Production as an Element of Analysis of Competitiveness of Metallurgical Enterprises
BULLETIN OF SCIENCE AND PRACTICE Оценка качества металлопродукции как элемент анализа конкурентоспособности металлургических предприятий
- 15 September 2019
- Published by Publishing Center Science and Practice in Bulletin of Science and Practice
- Vol. 5 (9) , 262-269
Quality Assessment of Metal Production as an Element of Analysis of Competitiveness of Metallurgical Enterprises
BULLETIN OF SCIENCE AND PRACTICE Оценка качества металлопродукции как элемент анализа конкурентоспособности металлургических предприятий
- Open Access
- 22 August 2019
- Published by National University of Science and Technology MISiS in Izvestiya. Ferrous Metallurgy
- Vol. 62 (7) , 548-556
Use of magnesian fluxes of the Khalilovo deposit in sinter production
Использование магнезиальных флюсов Халиловского месторождения при производстве агломерата
- 22 August 2019
- Published by National University of Science and Technology MISiS in Izvestiya. Ferrous Metallurgy
- Vol. 62 (7) , 548-556
Open AccessUse of magnesian fluxes of the Khalilovo deposit in sinter production
Использование магнезиальных флюсов Халиловского месторождения при производстве агломерата
- 1 June 2019
- Published by Allerton Press in Russian Engineering Research
- Vol. 39 (6) , 480-484
Decreasing the Impact–Abrasive Wear of Steel
A new method of assessing the impact–abrasive resistance of steel permits simulation of the impact–abrasive wear with variation in the magnitude and inclination of the impact force, type of...
- 1 June 2019
- Published by Allerton Press in Russian Engineering Research
- Vol. 39 (6) , 480-484
Decreasing the Impact–Abrasive Wear of Steel
A new method of assessing the impact–abrasive resistance of steel permits simulation of the impact–abrasive wear with variation in the magnitude and inclination of the impact force, type of...
- 1 March 2019
- Published by Allerton Press in Journal of Friction and Wear
- Vol. 40 (2) , 133-138
Evaluation Method of Impact and Abrasive Steel Resistance
A technique is developed for evaluating the impact-abrasive resistance of cast specimens, which allows simulating the conditions of impact and abrasive wear when changing the following...
- 1 March 2019
- Published by Allerton Press in Journal of Friction and Wear
- Vol. 40 (2) , 133-138
Evaluation Method of Impact and Abrasive Steel Resistance
A technique is developed for evaluating the impact-abrasive resistance of cast specimens, which allows simulating the conditions of impact and abrasive wear when changing the following...
- 1 February 2019
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 946, 500-505
Improvement of Agglomeration Technology by a Sinter Mix Preheating
A series of industrial experiments was carried out on the sinter machine No. 1 of the sinter department of JSC "Ural Steel". The dynamics of the sinter mix temperature during the technological stages of its preparation from pelleting to loading on pallets was studied, depending on a water temperature change during pelletizing. It was defined that for the winter working of the sinter department of JSC "Ural Steel" the water temperature increases, which supplied the pelletizer to moistening, for every 10 ° C, facilitates an increase in the temperature of the sinter mix on the pallets by 1.5-2.0 °C. Therefore, for stable sinter mix production with a temperature of more than 55 ° C, it is necessary to use water supplied to the pelletizer for moistening, with a temperature of at least 85°C. To implement the proposed technology, it is necessary to equip the sinter machines with water-heating recuperative heater, installed above the sintering machine behind the ignition hood and using heat, radiated from the surface of the sinter.
- 1 February 2019
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 946, 500-505
Improvement of Agglomeration Technology by a Sinter Mix Preheating
A series of industrial experiments was carried out on the sinter machine No. 1 of the sinter department of JSC "Ural Steel". The dynamics of the sinter mix temperature during the technological stages of its preparation from pelleting to loading on pallets was studied, depending on a water temperature change during pelletizing. It was defined that for the winter working of the sinter department of JSC "Ural Steel" the water temperature increases, which supplied the pelletizer to moistening, for every 10 ° C, facilitates an increase in the temperature of the sinter mix on the pallets by 1.5-2.0 °C. Therefore, for stable sinter mix production with a temperature of more than 55 ° C, it is necessary to use water supplied to the pelletizer for moistening, with a temperature of at least 85°C. To implement the proposed technology, it is necessary to equip the sinter machines with water-heating recuperative heater, installed above the sintering machine behind the ignition hood and using heat, radiated from the surface of the sinter.
- 1 January 2018
- Published by Allerton Press in Steel in Translation
- Vol. 48 (1) , 34-38
Magnesia Sinter with Flux Based on Magnesium Silicate
The experimental production of sinter with the addition of a byproduct of magnesite production— serpentinite–magnesite—is considered. This additive improves the strength of the sinter produced....
- 1 January 2018
- Published by Allerton Press in Steel in Translation
- Vol. 48 (1) , 34-38
Magnesia Sinter with Flux Based on Magnesium Silicate
The experimental production of sinter with the addition of a byproduct of magnesite production— serpentinite–magnesite—is considered. This additive improves the strength of the sinter produced....