Kigho Moses Oghenejoboh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Kigho Moses Oghenejoboh has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
Henry Oghenero Orugba
Department of Chemical and Petroleum Engineering, Delta State University Abraka, Oleh Campus, P.M.B 22, Oleh
2 shared publicationsUfuoma Modupe Oghenejoboh
Department of Chemistry, University of Ibadan, P.O. Box 22133, Ibadan
2 shared publicationsBamidele Solomon
Biochemical Engineering Laboratory, Department of Chemical Engineering, Obafemi Awolowo University, Ile-Ife, Nigeria
1 shared publicationBo Solomon
1 shared publicationE. J. Akpabio
Chemical & Petroleum Engineering Department University of Uyo, Uyo
1 shared publicationE.J. Akpabio
Department of Chemical & Petroleum Engineering University of Uyo, Uyo
1 shared publication
Latest Publications
- Open Access
- 13 February 2023
- Published by MDPI AG in Sustainability
- Vol. 15 (4) , 3383
Investigation of the Nutrient Composition of Fluted Pumpkin (Telfairia occidentalis) under Herbicide Treatment
During the 2013 and 2014 harvest seasons, field and laboratory experiments were conducted in Nigeria’s inferred agroecological zone. The nutritive value of fluted pumpkin (Telfairia occidentalis) leaves was evaluated by measuring the levels of carbohydrate, protein, fat, ash, dietary fiber, and moisture content in Telfairia occidentalis using the standard analytical methods. The experiment was laid out in a randomized complete block design (RCBD) and repeated four times. Three separate applications of paraquat herbicide (non-selective) at rates of 100, 150, and 200 L ha−1 were applied to the treated plots. Comparative studies of the nutritive value of T. occidentalis were observed in the treatment and control plots. The effects of herbicides showed that the proximate composition of the T. occidentalis leaves of the treated plot was 70% carbohydrate, 29% protein, 1.8% fat, 1.7% dietary fiber, 7.9% ash, and 8.7% moisture. In contrast, the values of the control plots were 6.5% carbohydrate, 1.9% protein, 1.5% fat, 1.2% dietary fiber, 7.0% ash, and 7.9% moisture. The results show that paraquat herbicide spray increased moisture, protein, fat, carbohydrate, ash, and vegetable yields in the treated plot and that T. occidentalis leaves are rich in lipids, fiber, and protein. As a result, the control plot’s fiber, carbohydrate, protein, ash, and moisture content decreased drastically without using paraquat. These results demonstrate that herbicides can affect the nutritional yield of T. occidentalis by eliminating weeds alongside the main crops (T. occidentalis) in the agroecological zone of south-eastern Nigeria. Therefore, if consumed in sufficient quantities, the studied leafy vegetables will significantly contribute to the nutritional needs of human health and the Nigerian population’s food security.
- 13 February 2023
- Published by MDPI AG in Sustainability
- Vol. 15 (4) , 3383
Open AccessInvestigation of the Nutrient Composition of Fluted Pumpkin (Telfairia occidentalis) under Herbicide Treatment
During the 2013 and 2014 harvest seasons, field and laboratory experiments were conducted in Nigeria’s inferred agroecological zone. The nutritive value of fluted pumpkin (Telfairia occidentalis) leaves was evaluated by measuring the levels of carbohydrate, protein, fat, ash, dietary fiber, and moisture content in Telfairia occidentalis using the standard analytical methods. The experiment was laid out in a randomized complete block design (RCBD) and repeated four times. Three separate applications of paraquat herbicide (non-selective) at rates of 100, 150, and 200 L ha−1 were applied to the treated plots. Comparative studies of the nutritive value of T. occidentalis were observed in the treatment and control plots. The effects of herbicides showed that the proximate composition of the T. occidentalis leaves of the treated plot was 70% carbohydrate, 29% protein, 1.8% fat, 1.7% dietary fiber, 7.9% ash, and 8.7% moisture. In contrast, the values of the control plots were 6.5% carbohydrate, 1.9% protein, 1.5% fat, 1.2% dietary fiber, 7.0% ash, and 7.9% moisture. The results show that paraquat herbicide spray increased moisture, protein, fat, carbohydrate, ash, and vegetable yields in the treated plot and that T. occidentalis leaves are rich in lipids, fiber, and protein. As a result, the control plot’s fiber, carbohydrate, protein, ash, and moisture content decreased drastically without using paraquat. These results demonstrate that herbicides can affect the nutritional yield of T. occidentalis by eliminating weeds alongside the main crops (T. occidentalis) in the agroecological zone of south-eastern Nigeria. Therefore, if consumed in sufficient quantities, the studied leafy vegetables will significantly contribute to the nutritional needs of human health and the Nigerian population’s food security.
- 1 September 2021
- Published by Ital Publication in Journal of Human, Earth, and Future
- Vol. 2 (3) , 258-268
Production of Biodiesel from a Novel Combination of Raphia Africana Kernel Oil and Turtle Shell (Centrochelys Sulcata) Heterogenous Catalyst
This work investigated the viability of a non-edible oil obtained from raphia africana in the production of biodiesel using a novel heterogeneous catalyst derived from turtle shells (Centrochelys sulcata). The study also proposed the use of acetone as co-solvent to enhance the solubility of the reacting mixtures. The turtle shells were calcined at 900oC for 3hr, impregnated in KOH to improve its activity and then supported with activated carbon produced from cassava peels to increase its surface area. The influences of KOH concentration, catalyst loading, catalyst/carbon mix ratio and concentration of acetone/methanol on the yield of biodiesel were investigated. The results obtained revealed that maximum biodiesel yield of 93% was obtained from the bio-oil at KOH concentration of 30% (w/w), catalyst loading of 6.5%, solvent/methanol ratio of 0.4 and catalyst/carbon weight ratio of 1.25. The activated carbon supported turtle shell catalyst has been found to possess very high catalytic activity converting bio-oil with high saturated fatty acid content to biodiesel with excellent fuel properties having low saturated fatty acids profile. Doi: 10.28991/HEF-2021-02-03-07 Full Text: PDF
- 1 September 2021
- Published by Ital Publication in Journal of Human, Earth, and Future
- Vol. 2 (3) , 258-268
Production of Biodiesel from a Novel Combination of Raphia Africana Kernel Oil and Turtle Shell (Centrochelys Sulcata) Heterogenous Catalyst
This work investigated the viability of a non-edible oil obtained from raphia africana in the production of biodiesel using a novel heterogeneous catalyst derived from turtle shells (Centrochelys sulcata). The study also proposed the use of acetone as co-solvent to enhance the solubility of the reacting mixtures. The turtle shells were calcined at 900oC for 3hr, impregnated in KOH to improve its activity and then supported with activated carbon produced from cassava peels to increase its surface area. The influences of KOH concentration, catalyst loading, catalyst/carbon mix ratio and concentration of acetone/methanol on the yield of biodiesel were investigated. The results obtained revealed that maximum biodiesel yield of 93% was obtained from the bio-oil at KOH concentration of 30% (w/w), catalyst loading of 6.5%, solvent/methanol ratio of 0.4 and catalyst/carbon weight ratio of 1.25. The activated carbon supported turtle shell catalyst has been found to possess very high catalytic activity converting bio-oil with high saturated fatty acid content to biodiesel with excellent fuel properties having low saturated fatty acids profile. Doi: 10.28991/HEF-2021-02-03-07 Full Text: PDF
- Open Access
- 1 August 2021
- Published by Elsevier in Environmental Challenges
- Vol. 4
Value added cassava waste management and environmental sustainability in Nigeria: A review
- 1 August 2021
- Published by Elsevier in Environmental Challenges
- Vol. 4
Open AccessValue added cassava waste management and environmental sustainability in Nigeria: A review
- Open Access
- 2 April 2016
- Published by University of Nigeria in Nigerian Journal of Technology
- Vol. 35 (2) , 329
BIOELECTRICITY PRODUCTION FROM CASSAVA MILL EFFLUENTS USING MICROBIAL FUEL CELL TECHNOLOGY
BIOELECTRICITY PRODUCTION FROM CASSAVA MILL EFFLUENTS USING MICROBIAL FUEL CELL TECHNOLOGY
- 2 April 2016
- Published by University of Nigeria in Nigerian Journal of Technology
- Vol. 35 (2) , 329
Open AccessBIOELECTRICITY PRODUCTION FROM CASSAVA MILL EFFLUENTS USING MICROBIAL FUEL CELL TECHNOLOGY
BIOELECTRICITY PRODUCTION FROM CASSAVA MILL EFFLUENTS USING MICROBIAL FUEL CELL TECHNOLOGY
- Open Access
- 1 January 2016
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Journal of Ecological Engineering
- Vol. 17 (2) , 52-58
APPLICATION OF CASSAVA PEELS ACTIVATED CARBON IN THE TREATMENT OF OIL REFINERY WASTEWATER – A COMPARATIVE ANALYSIS
A comparative analysis of the efficiency of activated carbon produced from fermented cassava peels (CPB), unfermented cassava peels (CPA) and commercial grade activated carbon (CAC) in the treatment of refinery wastewater was carried out. CPB was found to be 8% and 18% more efficient when...
- 1 January 2016
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Journal of Ecological Engineering
- Vol. 17 (2) , 52-58
Open AccessAPPLICATION OF CASSAVA PEELS ACTIVATED CARBON IN THE TREATMENT OF OIL REFINERY WASTEWATER – A COMPARATIVE ANALYSIS
A comparative analysis of the efficiency of activated carbon produced from fermented cassava peels (CPB), unfermented cassava peels (CPA) and commercial grade activated carbon (CAC) in the treatment of refinery wastewater was carried out. CPB was found to be 8% and 18% more efficient when...
- Open Access
- 10 January 2015
- Published by Sciencedomain International in British Journal of Applied Science & Technology
- Vol. 6 (2) , 164-171
Effects of Cassava Wastewater on the Quality of Receiving Water Body Intended for Fish Farming
Aim: The goal of the study is to determine the suitability of a pond into which cassava mill wastewater is discharged for fish farming. The pond which is located adjacent the Faculty of Engineering of the Delta State University, Oleh Campus is currently being proposed for acquisition by the Faculty for the project. Methodology: A total of 13 physicochemical parameters were analysed from samples collected at four different points around the pond. The parameters investigated were pH, CN, BOD, COD, DO, turbidity, conductivity, hardness, Pb2+, Hg2+ and Fe2+. The TSS, TDS, DO, total hardness were determined by the UV absorption spectrophotometer at 220 and the metal ions at 420nm respectively; while the Winkler’s titrimetric method was used to determine the COD and BOD. The pH, conductivity and turbidity were determined using the pH meter, conductivity meter and turbidity meter respectively. Results: The average cyanide content at the discharge point over the four weeks experimental period was 39.0±1.69 with a highly significant effect (p=0.042) and the lowest value of 3.8±0.01 mg/l was recorded 10 metres downstream of the discharge point. The COD, BOD, TDS and TSS at the discharge point were 1236±0.63 mg/l, 430.7±0.53 mg/l, 975±0.90 mg/l and 4030±9.26 mg/l respectively; while the Pb2+ and Hg2+ were higher at the sample point close to a refuse dump. Values recorded for all the tested parameters were far higher than that recommended for water bodies suitable for fish farming. Conclusion: The pond cannot be used for the intended project at its present form, it could be considered for use however, if all sources of pollution are stopped with proper remediation.
- 10 January 2015
- Published by Sciencedomain International in British Journal of Applied Science & Technology
- Vol. 6 (2) , 164-171
Open AccessEffects of Cassava Wastewater on the Quality of Receiving Water Body Intended for Fish Farming
Aim: The goal of the study is to determine the suitability of a pond into which cassava mill wastewater is discharged for fish farming. The pond which is located adjacent the Faculty of Engineering of the Delta State University, Oleh Campus is currently being proposed for acquisition by the Faculty for the project. Methodology: A total of 13 physicochemical parameters were analysed from samples collected at four different points around the pond. The parameters investigated were pH, CN, BOD, COD, DO, turbidity, conductivity, hardness, Pb2+, Hg2+ and Fe2+. The TSS, TDS, DO, total hardness were determined by the UV absorption spectrophotometer at 220 and the metal ions at 420nm respectively; while the Winkler’s titrimetric method was used to determine the COD and BOD. The pH, conductivity and turbidity were determined using the pH meter, conductivity meter and turbidity meter respectively. Results: The average cyanide content at the discharge point over the four weeks experimental period was 39.0±1.69 with a highly significant effect (p=0.042) and the lowest value of 3.8±0.01 mg/l was recorded 10 metres downstream of the discharge point. The COD, BOD, TDS and TSS at the discharge point were 1236±0.63 mg/l, 430.7±0.53 mg/l, 975±0.90 mg/l and 4030±9.26 mg/l respectively; while the Pb2+ and Hg2+ were higher at the sample point close to a refuse dump. Values recorded for all the tested parameters were far higher than that recommended for water bodies suitable for fish farming. Conclusion: The pond cannot be used for the intended project at its present form, it could be considered for use however, if all sources of pollution are stopped with proper remediation.
- Open Access
- 1 January 2015
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Journal of Ecological Engineering
- Vol. 16 (3) , 1-13
KINETIC MODELLING AND HALF LIFE STUDY OF ADSORPTIVE BIOREMEDIATION OF SOIL ARTIFICIALLY CONTAMINATED WITH BONNY LIGHT CRUDE OIL
- 1 January 2015
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Journal of Ecological Engineering
- Vol. 16 (3) , 1-13
Open AccessKINETIC MODELLING AND HALF LIFE STUDY OF ADSORPTIVE BIOREMEDIATION OF SOIL ARTIFICIALLY CONTAMINATED WITH BONNY LIGHT CRUDE OIL
- Open Access
- 10 January 2014
- Published by Sciencedomain International in British Journal of Applied Science & Technology
- Vol. 4 (5) , 808-822
Photocatalytic Degradation of Chlorobenzene in Aqueous Solutions–Comparison of Tio2 with Periwinkle and Snail Shells’ Powder as Photo Catalyst
Aim: The goal of the study is to determine the efficiency of periwinkle shell powder and snail shell powder – two locally prepared photocatalysts in comparison with TiO2 in the treatment of wastewater polluted with chlorobenzene. Place and Duration of Study: The present study was conducted between January and October 2011 at the Department of Chemical Engineering, University of Benin-Nigeria as part of a Master of Engineering Degree research project. Methodology: The obtained periwinkle (PSA) and snail (SSA) shells were crushed to powder, sieved and then analysed for the functional group (especially the transition metals) using Fourier Transform Infra-red (FTIR) analysis. The catalytic activity of the unmodified PSA, SSA as well as their modification with H2O2 were then compared with commercial grade TiO2 (Degussa P25) for the degradation of chlorobenzene in wastewater both under laboratory condition (dark) and solar irradiation using sets of special boron-silica glass reactors. UV/VIS spectrophotometer model T70 installed with printer was used for the determination of chlorobenzene concentration while BET surface area of the catalysts was determined by means of nitrogen adsorption/desorption isotherm. Results: The result show that the photocatalytic activity of pure PSA and SSA were very poor when compared with TiO2. However, PSA and SSA modified with H2O2 showed greater promise as their degradation efficiency increased by 87.98% and 41.72% respectively. Conclusion: PSA and SSA cannot be used as photocatalyst for the degradation of organic pollutants in aqueous solution without being modified or doped with appropriate metal or non metal dopants.
- 10 January 2014
- Published by Sciencedomain International in British Journal of Applied Science & Technology
- Vol. 4 (5) , 808-822
Open AccessPhotocatalytic Degradation of Chlorobenzene in Aqueous Solutions–Comparison of Tio2 with Periwinkle and Snail Shells’ Powder as Photo Catalyst
Aim: The goal of the study is to determine the efficiency of periwinkle shell powder and snail shell powder – two locally prepared photocatalysts in comparison with TiO2 in the treatment of wastewater polluted with chlorobenzene. Place and Duration of Study: The present study was conducted between January and October 2011 at the Department of Chemical Engineering, University of Benin-Nigeria as part of a Master of Engineering Degree research project. Methodology: The obtained periwinkle (PSA) and snail (SSA) shells were crushed to powder, sieved and then analysed for the functional group (especially the transition metals) using Fourier Transform Infra-red (FTIR) analysis. The catalytic activity of the unmodified PSA, SSA as well as their modification with H2O2 were then compared with commercial grade TiO2 (Degussa P25) for the degradation of chlorobenzene in wastewater both under laboratory condition (dark) and solar irradiation using sets of special boron-silica glass reactors. UV/VIS spectrophotometer model T70 installed with printer was used for the determination of chlorobenzene concentration while BET surface area of the catalysts was determined by means of nitrogen adsorption/desorption isotherm. Results: The result show that the photocatalytic activity of pure PSA and SSA were very poor when compared with TiO2. However, PSA and SSA modified with H2O2 showed greater promise as their degradation efficiency increased by 87.98% and 41.72% respectively. Conclusion: PSA and SSA cannot be used as photocatalyst for the degradation of organic pollutants in aqueous solution without being modified or doped with appropriate metal or non metal dopants.
- Open Access
- 10 January 2012
- Published by Sciencedomain International in British Biotechnology Journal
- Vol. 2 (4) , 257-268
Effects of Starch Fermentation on the Shelf-Life of Cassava Starch Based Adhesive
The effects of natural fermentation on the stability or shelf life of adhesives produced from starch of two cassava varieties (Manihot utilissima and Manihot palmate) were studied. It was observed that the HCN content of the Manihot utilissima reduced from 35.74±0.11 mg/kg for unfermented starch sample to 6.93±0.25 mg/kg after 5 days of fermentation (p = 0.037), while the sample’s pH increased from 4.60±0.05 to 6.89±00 respectively. However, the reduction in HCN concentration and corresponding increase in pH for manihot palmate were only marginal, as the concentration of HCN in the starch reduced from 2.49±0.12 to 0.89±0.26 while the pH increased from 6.02±0.04 to 6.35±0.05 after five days of fermentation. The viscosity test conducted at room temperature for a period of 30 days to determine the stability or shelf of the produced adhesives show that adhesives produced from unfermented Manihot utilissima starch sample as well as samples of that cassava variety fermented for only 1 day have longer shelf-life as exemplified by the relative stable low viscosity of the adhesive over the 30 days test period with a highly significant effect, (p = 0.018). The drying time of Manihot utilissima was significantly high at 7.1±0.01 minutes (p = 0.041) and remained relatively stable for the 30 days storage time. The results therefore show that the higher the cassava starch acidity the lower its viscosity, the higher its drying time and the longer its shelf-life.
- 10 January 2012
- Published by Sciencedomain International in British Biotechnology Journal
- Vol. 2 (4) , 257-268
Open AccessEffects of Starch Fermentation on the Shelf-Life of Cassava Starch Based Adhesive
The effects of natural fermentation on the stability or shelf life of adhesives produced from starch of two cassava varieties (Manihot utilissima and Manihot palmate) were studied. It was observed that the HCN content of the Manihot utilissima reduced from 35.74±0.11 mg/kg for unfermented starch sample to 6.93±0.25 mg/kg after 5 days of fermentation (p = 0.037), while the sample’s pH increased from 4.60±0.05 to 6.89±00 respectively. However, the reduction in HCN concentration and corresponding increase in pH for manihot palmate were only marginal, as the concentration of HCN in the starch reduced from 2.49±0.12 to 0.89±0.26 while the pH increased from 6.02±0.04 to 6.35±0.05 after five days of fermentation. The viscosity test conducted at room temperature for a period of 30 days to determine the stability or shelf of the produced adhesives show that adhesives produced from unfermented Manihot utilissima starch sample as well as samples of that cassava variety fermented for only 1 day have longer shelf-life as exemplified by the relative stable low viscosity of the adhesive over the 30 days test period with a highly significant effect, (p = 0.018). The drying time of Manihot utilissima was significantly high at 7.1±0.01 minutes (p = 0.041) and remained relatively stable for the 30 days storage time. The results therefore show that the higher the cassava starch acidity the lower its viscosity, the higher its drying time and the longer its shelf-life.
- Open Access
- 1 February 2002
- Published by African Journals Online (AJOL) in Global Journal of Engineering Research
- Vol. 1 (2) , 81-88
ADAPTATION OF NATURAL GAS FOR MOTOR FUELS IN NIGERIA TRANSPORT SYSTEM
In recent years, as a result of limiting reserve of crude oil and the clamour for the deregulation of the petroleum sector of the nation's economy, there is need to look beyond liquid fuel (gasoline, diesel) as vehicular fuels. The viability of adapting natural gas for motor fuels had been presented. Natural gas as automobile fuel has a multiple of advantages over liquid fuel. These include high octane number, less negative effects on engine parts, low toxicity of effluents. (i.e. low CO, NOX, and lead emissions.) Experiences of other countries that are presently using natural gas as automobile fuel are reviewed along with the efforts put in place by Nigeria through the Nigerian Gas Company (NGC) Limited to experiment the project. The need of government through the NGC to be fully involved in the planning and execution of a retrofit plan to optimize pipeline network and supply service of natural gas to refueling and refilling stations is also emphasized. The public on the other hand requires enlightenment on the need to convert their vehicles to gas/gasoline powered, and incentives given for patronizing natural gas filling stations. A cohesive interplay of both national and corporate interests in policy formulation and implementation will harness effective distribution and utilization of natural gas within the Nigeria socio-economic sector. Key words: Gas, Fuel, Automobile, Technology, Project. [Global Jnl Engineering Res. Vol.1(2) 2002: 81-88]
- 1 February 2002
- Published by African Journals Online (AJOL) in Global Journal of Engineering Research
- Vol. 1 (2) , 81-88
Open AccessADAPTATION OF NATURAL GAS FOR MOTOR FUELS IN NIGERIA TRANSPORT SYSTEM
In recent years, as a result of limiting reserve of crude oil and the clamour for the deregulation of the petroleum sector of the nation's economy, there is need to look beyond liquid fuel (gasoline, diesel) as vehicular fuels. The viability of adapting natural gas for motor fuels had been presented. Natural gas as automobile fuel has a multiple of advantages over liquid fuel. These include high octane number, less negative effects on engine parts, low toxicity of effluents. (i.e. low CO, NOX, and lead emissions.) Experiences of other countries that are presently using natural gas as automobile fuel are reviewed along with the efforts put in place by Nigeria through the Nigerian Gas Company (NGC) Limited to experiment the project. The need of government through the NGC to be fully involved in the planning and execution of a retrofit plan to optimize pipeline network and supply service of natural gas to refueling and refilling stations is also emphasized. The public on the other hand requires enlightenment on the need to convert their vehicles to gas/gasoline powered, and incentives given for patronizing natural gas filling stations. A cohesive interplay of both national and corporate interests in policy formulation and implementation will harness effective distribution and utilization of natural gas within the Nigeria socio-economic sector. Key words: Gas, Fuel, Automobile, Technology, Project. [Global Jnl Engineering Res. Vol.1(2) 2002: 81-88]