Ricardo Martins
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Ricardo Martins has a total of 48 co-authors. Here are the top co-authors by number of shared publications:
- Jorge Leandro
Chair of Hydromechanics and Hydraulic Engineering, Faculty IV School of Science and Technology, University of Siegen, Paul-Bonatz-Str. 9–11, 57068 Siegen, Germany
12 shared publications - Slobodan Djordjević
University of Exeter
9 shared publications - Jan Jacob Keizer
GeoBioTec, Department of Environment and Planning, University of Aveiro, Portugal
8 shared publications - Jjoão Luis Mendes Pedroso De Lima
MARE—Marine and Environmental Sciences Centre, ARNET—Aquatic Research Network, Department of Civil Engineering, Faculty of Sciences and Technology, University of Coimbra, Rua Luís Reis Santos, Pólo II—Universidade de Coimbra, 3030-788 Coimbra, Portugal
8 shared publications - Jorge Manuel Guieiro Pereira Isidoro
Institute of Engineering, University of Algarve (UAlg)/Centre for Marine and Environmental Research (CIMA)
7 shared publications - Matteo Rubinato
Centre for Agroecology, Water and Resilience, Ryton Gardens, Wolston Lane, Ryton-on-Dunsmore, Coventry University, Coventry CV8 3LG, UK
5 shared publications
Latest Publications
- 26 September 2026
- Published by Taylor & Francis in Urban Water Journal
- p. 1-14
Influence of invert channel height and floor slope on the hydraulic performance of manholes
1. Urban flooding has significant socio-economic consequences worldwide (Butcher et al. 2023). A lack of hydraulic capacity within drainage systems increases the risk of combined sewer overflows. M...
- 26 September 2026
- Published by Taylor & Francis in Urban Water Journal
- p. 1-14
Influence of invert channel height and floor slope on the hydraulic performance of manholes
1. Urban flooding has significant socio-economic consequences worldwide (Butcher et al. 2023). A lack of hydraulic capacity within drainage systems increases the risk of combined sewer overflows. M...
- Open Access
- 20 January 2025
- Published by Copernicus GmbH
Estimating open channel surface flow velocities under low luminosity conditions, using fluorescent quinine-based tracing techniques and UAS imagery
This study discusses the application of innovative fluorescent quinine-based tracer techniques to estimate surface flow velocities under low luminosity conditions. Quinine is known for its luminescent properties when exposed to ultraviolet A (UVA) light. This research involves fieldwork measurements conducted in open channels with varying hydraulic characteristics. The application of quinine solutions in liquid and solid (ice cubes) states into the water flow allows the recording of the movement of the tracers. This movement is registered by tracking the leading edge of the liquid tracer plume or solid particles over specific time intervals. An Unmanned Aerial System (UAS) equipped with a camera was used to record the movement of the tracers in the channels. To benchmark the performance of the quinine-based tracers, flowmeter-based velocity maps and a thermal tracer technique were employed in the experiments. Results indicated that both liquid and solid quinine solution tracers successfully estimated open channel surface flow velocities under low luminosity conditions. The quinine solid tracer can be used as a dual (fluorescent-thermal) tracer and, despite its smaller volume used in the experiments compared to the liquid tracer, the solid form was easier to track. This was attributed to the conservation of a higher quinine concentration for longer periods of time in the solid tracers, resulting in a higher contrast easier to identify. On the other hand, the liquid tracer faded earlier due to diffusion in the turbulent flow. Nonetheless, the main advantage of using the liquid over the solid tracer was its easier availability for the experiments. This study highlights the applicability and reliability of quinine-based tracers in estimating surface flow velocities, in low luminosity conditions. The use of the UAS in the measurements’ set-up facilitated and enhanced data collection, contributing to the accuracy of the results. The observational approach allowed for capturing the inherent luminescent properties of quinine when exposed to UVA light using minimal tracer quantities.
- 20 January 2025
- Published by Copernicus GmbH
Open AccessEstimating open channel surface flow velocities under low luminosity conditions, using fluorescent quinine-based tracing techniques and UAS imagery
This study discusses the application of innovative fluorescent quinine-based tracer techniques to estimate surface flow velocities under low luminosity conditions. Quinine is known for its luminescent properties when exposed to ultraviolet A (UVA) light. This research involves fieldwork measurements conducted in open channels with varying hydraulic characteristics. The application of quinine solutions in liquid and solid (ice cubes) states into the water flow allows the recording of the movement of the tracers. This movement is registered by tracking the leading edge of the liquid tracer plume or solid particles over specific time intervals. An Unmanned Aerial System (UAS) equipped with a camera was used to record the movement of the tracers in the channels. To benchmark the performance of the quinine-based tracers, flowmeter-based velocity maps and a thermal tracer technique were employed in the experiments. Results indicated that both liquid and solid quinine solution tracers successfully estimated open channel surface flow velocities under low luminosity conditions. The quinine solid tracer can be used as a dual (fluorescent-thermal) tracer and, despite its smaller volume used in the experiments compared to the liquid tracer, the solid form was easier to track. This was attributed to the conservation of a higher quinine concentration for longer periods of time in the solid tracers, resulting in a higher contrast easier to identify. On the other hand, the liquid tracer faded earlier due to diffusion in the turbulent flow. Nonetheless, the main advantage of using the liquid over the solid tracer was its easier availability for the experiments. This study highlights the applicability and reliability of quinine-based tracers in estimating surface flow velocities, in low luminosity conditions. The use of the UAS in the measurements’ set-up facilitated and enhanced data collection, contributing to the accuracy of the results. The observational approach allowed for capturing the inherent luminescent properties of quinine when exposed to UVA light using minimal tracer quantities.
- Open Access
- 16 September 2024
- Published by Elsevier in Journal of Hydrology
- Vol. 643
High spatiotemporal resolution free surface detection using cost-effective video equipment and computer vision techniques in nearly stationary flow along a transparent wall in the laboratory
- 16 September 2024
- Published by Elsevier in Journal of Hydrology
- Vol. 643
Open AccessHigh spatiotemporal resolution free surface detection using cost-effective video equipment and computer vision techniques in nearly stationary flow along a transparent wall in the laboratory
- 30 September 2023
- Published by Elsevier in Flow Measurement and Instrumentation
- Vol. 94
Design and characterisation of customised-roughness beds for open-channel flow experiments
- 30 September 2023
- Published by Elsevier in Flow Measurement and Instrumentation
- Vol. 94
Design and characterisation of customised-roughness beds for open-channel flow experiments
- Open Access
- 19 May 2023
- Published by Elsevier in Hydrology Research
- Vol. 54 (6) , 782-795
Fluorescent quinine-based tracking techniques for measurement of open-channel surface flow velocities under low luminosity conditions using a UAS
- 19 May 2023
- Published by Elsevier in Hydrology Research
- Vol. 54 (6) , 782-795
Open AccessFluorescent quinine-based tracking techniques for measurement of open-channel surface flow velocities under low luminosity conditions using a UAS
- Open Access
- 15 May 2023
- Published by Copernicus GmbH
Estimating sheet flow velocities using quinine as a fluorescent tracer in low luminosity conditions: laboratory and field experiments
This study presents a technique based on the use of quinine as a fluorescent tracer, to estimate sheet flow velocities over various surface coverings (e.g., bare; mulched; vegetated; paved) in low luminosity conditions (e.g., night; twilight; shielded environments). Quinine glows when exposed to UVA light and in the concentrations used is not harmful to the environment. Experimental work was conducted for studying sheet flows in the i) laboratory (using a soil flume), over bare and mulched surfaces, and ii) field, over vegetated and paved surfaces. Flow velocities were estimated based on the injection of a quinine solution into the water flow. In these experiments, dye and thermal tracer techniques were used as a benchmark for assessing the performance of the quinine tracer. Optical and infrared cameras were used to record the movement of the tracers’ plumes in the flow. The surface velocity of the flow was estimated by tracking the tracers’ plumes leading-edge and calculating their travel distance over a certain time lapse. Overall, the visibility of the quinine tracer was better in comparison to the dye tracer. However, under some circumstances, lower than the visibility of the thermal tracer. Nonetheless, the results show that all three tracers yielded similar estimations of the flow velocities. Therefore, when exposed to UVA light the quinine tracer can be useful to estimate sheet flow velocities over a wide variety of soil and urban surfaces in low luminosity conditions. Despite some inherent limitations of this technique (e.g., invisible under bright light conditions or heavy mulched/vegetated cover; need of a UVA lamp), its main advantage is the high visibility of the quinine fluorescent tracer under UVA light for fade light conditions (e.g., night; twilight; shielded environments such as close conduits), which creates new opportunities for tracer-based surface flow velocity measurements in surface hydrology studies.
- 15 May 2023
- Published by Copernicus GmbH
Open AccessEstimating sheet flow velocities using quinine as a fluorescent tracer in low luminosity conditions: laboratory and field experiments
This study presents a technique based on the use of quinine as a fluorescent tracer, to estimate sheet flow velocities over various surface coverings (e.g., bare; mulched; vegetated; paved) in low luminosity conditions (e.g., night; twilight; shielded environments). Quinine glows when exposed to UVA light and in the concentrations used is not harmful to the environment. Experimental work was conducted for studying sheet flows in the i) laboratory (using a soil flume), over bare and mulched surfaces, and ii) field, over vegetated and paved surfaces. Flow velocities were estimated based on the injection of a quinine solution into the water flow. In these experiments, dye and thermal tracer techniques were used as a benchmark for assessing the performance of the quinine tracer. Optical and infrared cameras were used to record the movement of the tracers’ plumes in the flow. The surface velocity of the flow was estimated by tracking the tracers’ plumes leading-edge and calculating their travel distance over a certain time lapse. Overall, the visibility of the quinine tracer was better in comparison to the dye tracer. However, under some circumstances, lower than the visibility of the thermal tracer. Nonetheless, the results show that all three tracers yielded similar estimations of the flow velocities. Therefore, when exposed to UVA light the quinine tracer can be useful to estimate sheet flow velocities over a wide variety of soil and urban surfaces in low luminosity conditions. Despite some inherent limitations of this technique (e.g., invisible under bright light conditions or heavy mulched/vegetated cover; need of a UVA lamp), its main advantage is the high visibility of the quinine fluorescent tracer under UVA light for fade light conditions (e.g., night; twilight; shielded environments such as close conduits), which creates new opportunities for tracer-based surface flow velocity measurements in surface hydrology studies.
- Open Access
Estimating Sheet Flow Velocities Using Quinine as a Fluorescent Tracer: Bare, Mulched, Vegetated and Paved Surfaces
When direct flow velocity measurements are not feasible, the use of tracers can be a valuable tool. In the present study, both laboratory and field experiments were conducted to evaluate the applicability of quinine as a fluorescent tracer for estimating mean sheet flow velocities in different ambient light and surface morphology conditions. Quinine excels in low-light conditions when exposed to UVA light. This tracer was compared with dye and thermal tracers, all in liquid form. In these tracing techniques the tracers were injected into the flow, after which surface velocity was estimated by tracking the leading edge of the tracer plumes and applying a correction factor to calculate the mean velocity (in a water column). The visibility of the tracers was evaluated by measuring the relative luminance and contrast ratio of the quinine and dye tracer plumes. Results show that the quinine tracer can be used to estimate sheet flow velocities over a wide variety of soil and urban surfaces; it has better visibility in comparison to the dye tracer but, in some conditions, lower visibility than the thermal tracer. Although quinine is invisible under bright ambient light conditions, this tracer technique requires low-cost experimental setup and is useful in low-light conditions (e.g., night; twilight; shielded environments).
Open AccessEstimating Sheet Flow Velocities Using Quinine as a Fluorescent Tracer: Bare, Mulched, Vegetated and Paved Surfaces
When direct flow velocity measurements are not feasible, the use of tracers can be a valuable tool. In the present study, both laboratory and field experiments were conducted to evaluate the applicability of quinine as a fluorescent tracer for estimating mean sheet flow velocities in different ambient light and surface morphology conditions. Quinine excels in low-light conditions when exposed to UVA light. This tracer was compared with dye and thermal tracers, all in liquid form. In these tracing techniques the tracers were injected into the flow, after which surface velocity was estimated by tracking the leading edge of the tracer plumes and applying a correction factor to calculate the mean velocity (in a water column). The visibility of the tracers was evaluated by measuring the relative luminance and contrast ratio of the quinine and dye tracer plumes. Results show that the quinine tracer can be used to estimate sheet flow velocities over a wide variety of soil and urban surfaces; it has better visibility in comparison to the dye tracer but, in some conditions, lower visibility than the thermal tracer. Although quinine is invisible under bright ambient light conditions, this tracer technique requires low-cost experimental setup and is useful in low-light conditions (e.g., night; twilight; shielded environments).
- Open Access
- 28 March 2022
- Published by Copernicus GmbH
Wildfire ash mobilization by run-on under controlled laboratory conditions: Qualitative analysis
Globally, high erosion rates are being triggered by extreme rainfall/runoff events. Ashes and char, by-product of devastating wildfires are the first particles mobilized and depleted. The contribution of the ash/char layer to the overall erosion process is still unestablished especially since separating ash and char fraction from litter, soil and eroded sediments is far from trivial. To address this knowledge gap, ASHMOB project (CENTRO-01-0145-FEDER-029351) is studying the mobilization of wildfire ash by wind and water erosion under controlled laboratory conditions as well as field conditions. The present study aims at contributing to the current knowledge on the physical process behind the mobilization of ashes and char when subject to runoff. This research is the second phase of the physical experiments on the mobilization by water of wildfire ash and char, performed at the Laboratory of Hydraulics, Water Resources and Environment of the University of Coimbra. To characterize ash erosion, a multi-channel flume was used (i.e., 5 parallel equal channels), which runs 5 replicate run-on events with exactly the same hydraulic conditions. To collect the full sample, a cart with trays moved at an established and controlled pace under the flumes, allowing the collection of water, ashes and sediments, thus characterising both hydrographs and ash yields for all event and replicate. Temporal resolution was fixed at 20 seconds per tray. Six major variables were tested: (1) Ash depth; (2) Type of burnt vegetation; (3) Ash layer length; (4) Ash particle size; (5) Slope. Preliminary results show that: (1) Smaller ash depths require lower flows to be mobilised by; (2) Pinus pinaster and Eucalyptus globulus have a different behaviour from Arbutus unedo ashes as the former tend to be transported more as a "aggregated block or chunk", possibly due to buoyancy, and the latter more like sediments; It was also observed that a higher number of large particles of char tend to provide a somewhat larger protection to the finer ashes than having little or no large particles of char; (3) a longer, in the flow direction, layer of Arbutus unedo ashes has little to no impact in the mobilisation process, whereas for the other vegetations, a longer layer implies less transport relative to the initial amount of ashes; (4) smaller particle sizes, when left without the "protection" of larger char particles are transported more easily; (5) Slope has a large impact on the transport of ashes, especially when considering the same bed roughness.
- 28 March 2022
- Published by Copernicus GmbH
Open AccessWildfire ash mobilization by run-on under controlled laboratory conditions: Qualitative analysis
Globally, high erosion rates are being triggered by extreme rainfall/runoff events. Ashes and char, by-product of devastating wildfires are the first particles mobilized and depleted. The contribution of the ash/char layer to the overall erosion process is still unestablished especially since separating ash and char fraction from litter, soil and eroded sediments is far from trivial. To address this knowledge gap, ASHMOB project (CENTRO-01-0145-FEDER-029351) is studying the mobilization of wildfire ash by wind and water erosion under controlled laboratory conditions as well as field conditions. The present study aims at contributing to the current knowledge on the physical process behind the mobilization of ashes and char when subject to runoff. This research is the second phase of the physical experiments on the mobilization by water of wildfire ash and char, performed at the Laboratory of Hydraulics, Water Resources and Environment of the University of Coimbra. To characterize ash erosion, a multi-channel flume was used (i.e., 5 parallel equal channels), which runs 5 replicate run-on events with exactly the same hydraulic conditions. To collect the full sample, a cart with trays moved at an established and controlled pace under the flumes, allowing the collection of water, ashes and sediments, thus characterising both hydrographs and ash yields for all event and replicate. Temporal resolution was fixed at 20 seconds per tray. Six major variables were tested: (1) Ash depth; (2) Type of burnt vegetation; (3) Ash layer length; (4) Ash particle size; (5) Slope. Preliminary results show that: (1) Smaller ash depths require lower flows to be mobilised by; (2) Pinus pinaster and Eucalyptus globulus have a different behaviour from Arbutus unedo ashes as the former tend to be transported more as a "aggregated block or chunk", possibly due to buoyancy, and the latter more like sediments; It was also observed that a higher number of large particles of char tend to provide a somewhat larger protection to the finer ashes than having little or no large particles of char; (3) a longer, in the flow direction, layer of Arbutus unedo ashes has little to no impact in the mobilisation process, whereas for the other vegetations, a longer layer implies less transport relative to the initial amount of ashes; (4) smaller particle sizes, when left without the "protection" of larger char particles are transported more easily; (5) Slope has a large impact on the transport of ashes, especially when considering the same bed roughness.
- Open Access
- 28 March 2022
- Published by Copernicus GmbH
A lysimeter study of nutrient mobilization from wildfire and factory ashes by overland flow and soil leaching
Wildfires are documented to affect physical, chemical and biological properties of topsoil. Besides through the direct heating-induced impacts, wildfires can also affect topsoil properties indirectly through the ash layer deposited on the soil surface immediately after fire. These indirect ash effects are less well understood, because of the marked dynamics in ash loads with time-since-fire due to mobilization by wind and water erosion. Therefore, we took advantage of a lysimeter study - a controlled experiment under field conditions - into the mobilization of ashes by overland flow, to address the ash impacts on topsoil nutrient contents. The lysimeter study involved a total of 15 lysimeters with a surface area of 50 cm by 120 cm and at a slope angle of approximately 10°. The lysimeters were equally and randomly distributed over five treatments. Four treatments involved the application of two types of ash at a rate of 500 g.m-2 on a 2-3cm-thick layer of soil (in fact, sediments from the Mondego river), while the fifth, control treatment did not. One ash type consisted of black ashes collected in a 2020 burnt mature pine plantation in north-central Portugal, while the white ashes were obtained from a paper mill factory. In turn, two treatments per ash type involved the presence vs. absence of a 10cm-wide strip of 1cm-diameter PVC bars with a density of 1000 bars per m-2, mimicking a riparian vegetation zone and, assess its effectiveness to retain eroded ashes preventing them from entering streams. The lysimeter experiment ran for 7 weeks, starting on September 6 (ash application) and ending on 22 October 2021, covering the period that typically corresponds to the initial phase of the post-fire window-of-disturbance in the study region. At the end of the experiment, the upper 2cm of the soil were sampled at 3 locations within each lysimeter, in its middle and halfway its upper and lower halves. This was done after removing the remaining ashes on the soil surface. All soil samples were analysed for their contents of available Phosphorus (Pav) and total Nitrogen (TN) but, at this moment, only the Pav analyses have been concluded. The preliminary Pav results revealed a much smaller enrichment by the black than white ashes. The median Pav contents were 4.6 microgram per gram of soil for the control lysimeters as opposed to 5.6 and 9.2 microgram per gram of soil for the lysimeters with black and white ashes, respectively. This difference in enrichment could be linked to the differences in Pav content of the two ash types, being 1.9 and 1.0 microgram per gram of the white and black ash, respectively. Furthermore, the Pav enrichment was not affected by the presence/absence of the simulated riparian zone at the bottom of the lysimeters, as the differences in Pav contents of the lysimeters with and without these zones amounted to 0.1 microgram Pav per gram of soil in the case of both the black and the white ashes.
- 28 March 2022
- Published by Copernicus GmbH
Open AccessA lysimeter study of nutrient mobilization from wildfire and factory ashes by overland flow and soil leaching
Wildfires are documented to affect physical, chemical and biological properties of topsoil. Besides through the direct heating-induced impacts, wildfires can also affect topsoil properties indirectly through the ash layer deposited on the soil surface immediately after fire. These indirect ash effects are less well understood, because of the marked dynamics in ash loads with time-since-fire due to mobilization by wind and water erosion. Therefore, we took advantage of a lysimeter study - a controlled experiment under field conditions - into the mobilization of ashes by overland flow, to address the ash impacts on topsoil nutrient contents. The lysimeter study involved a total of 15 lysimeters with a surface area of 50 cm by 120 cm and at a slope angle of approximately 10°. The lysimeters were equally and randomly distributed over five treatments. Four treatments involved the application of two types of ash at a rate of 500 g.m-2 on a 2-3cm-thick layer of soil (in fact, sediments from the Mondego river), while the fifth, control treatment did not. One ash type consisted of black ashes collected in a 2020 burnt mature pine plantation in north-central Portugal, while the white ashes were obtained from a paper mill factory. In turn, two treatments per ash type involved the presence vs. absence of a 10cm-wide strip of 1cm-diameter PVC bars with a density of 1000 bars per m-2, mimicking a riparian vegetation zone and, assess its effectiveness to retain eroded ashes preventing them from entering streams. The lysimeter experiment ran for 7 weeks, starting on September 6 (ash application) and ending on 22 October 2021, covering the period that typically corresponds to the initial phase of the post-fire window-of-disturbance in the study region. At the end of the experiment, the upper 2cm of the soil were sampled at 3 locations within each lysimeter, in its middle and halfway its upper and lower halves. This was done after removing the remaining ashes on the soil surface. All soil samples were analysed for their contents of available Phosphorus (Pav) and total Nitrogen (TN) but, at this moment, only the Pav analyses have been concluded. The preliminary Pav results revealed a much smaller enrichment by the black than white ashes. The median Pav contents were 4.6 microgram per gram of soil for the control lysimeters as opposed to 5.6 and 9.2 microgram per gram of soil for the lysimeters with black and white ashes, respectively. This difference in enrichment could be linked to the differences in Pav content of the two ash types, being 1.9 and 1.0 microgram per gram of the white and black ash, respectively. Furthermore, the Pav enrichment was not affected by the presence/absence of the simulated riparian zone at the bottom of the lysimeters, as the differences in Pav contents of the lysimeters with and without these zones amounted to 0.1 microgram Pav per gram of soil in the case of both the black and the white ashes.
- Open Access
- 28 March 2022
- Published by Copernicus GmbH
Mobilization of black and white ashes by overland flow and their retention by riparian vegetation - preliminary results from a lysimeter experiment
Wildfires are now widely documented to produce strong to extreme runoff and erosion responses during the so-called window-of-disturbance. However, the role of wildfire ash in post-fire runoff generation and especially the contribution of wildfire ash to post-fire erosion rates are still poorly studied. The same applies for the effectiveness of erosion control measures to reduce ash mobilization by runoff. To address these knowledge gaps, we carried out a lysimeter experiment in which overland flow and the associated transport of sediments and ashes was compared for five treatments. Four treatments involved the application of black ash from a wildfire or white ash from a paper pulp factory, both with and without a simulated riparian strip at the bottom of the slope, while the fifth treatment was the control without ash as well as without the riparian strip. Each of the five treatments was applied to three randomly selected lysimeters. The lysimeters had a surface area of 50 cm by 120 cm, a slope angle of approximately 10 degrees and were topped up with a 2-3cm-thick layer of soil (in fact, sediments from the Mondego river) over a sand and a gravel layer. Overland flow was collected at the bottom of the lysimeters and diverted into a tank using a garden hose. The experiment started on 6 September 2021 with the application of the ash at a rate of 500 g m-2 and ended on 22 October 2021, coinciding with the initial phase of the post-fire window-of-disturbance in the study region. During this 7-week period, overland flow was measured at a total of five occasions following significant rainfall events and, whenever possible, samples collected for laboratory analysis of their concentration of total suspended sediment (TSS) and their organic matter fractions. The preliminary results for the lysimeters without riparian strip suggested that the two types of ashes played contrasting roles in overland flow generation. The average amount of overland flow over the 7-week period was higher for the lysimeters with white ashes than for the control lysimeters (36.0 vs. 31.2 l), while the opposite was true for the lysimeters with black ashes (26.8 l). These differences in overland flow were associated with differences in TSS concentrations that were the opposite, averaging 11.7 and 20.4 g l-1 over the entire study period in the case of the lysimeters with white and black ashes, respectively. The overall TSS concentrations also suggested a marked role for the riparian strips but only in the case of the black ashes, dropping to 15.3 g l-1. In the case of the white ashes, the overall TSS concentrations were the same with as without the riparian strips.
- 28 March 2022
- Published by Copernicus GmbH
Open AccessMobilization of black and white ashes by overland flow and their retention by riparian vegetation - preliminary results from a lysimeter experiment
Wildfires are now widely documented to produce strong to extreme runoff and erosion responses during the so-called window-of-disturbance. However, the role of wildfire ash in post-fire runoff generation and especially the contribution of wildfire ash to post-fire erosion rates are still poorly studied. The same applies for the effectiveness of erosion control measures to reduce ash mobilization by runoff. To address these knowledge gaps, we carried out a lysimeter experiment in which overland flow and the associated transport of sediments and ashes was compared for five treatments. Four treatments involved the application of black ash from a wildfire or white ash from a paper pulp factory, both with and without a simulated riparian strip at the bottom of the slope, while the fifth treatment was the control without ash as well as without the riparian strip. Each of the five treatments was applied to three randomly selected lysimeters. The lysimeters had a surface area of 50 cm by 120 cm, a slope angle of approximately 10 degrees and were topped up with a 2-3cm-thick layer of soil (in fact, sediments from the Mondego river) over a sand and a gravel layer. Overland flow was collected at the bottom of the lysimeters and diverted into a tank using a garden hose. The experiment started on 6 September 2021 with the application of the ash at a rate of 500 g m-2 and ended on 22 October 2021, coinciding with the initial phase of the post-fire window-of-disturbance in the study region. During this 7-week period, overland flow was measured at a total of five occasions following significant rainfall events and, whenever possible, samples collected for laboratory analysis of their concentration of total suspended sediment (TSS) and their organic matter fractions. The preliminary results for the lysimeters without riparian strip suggested that the two types of ashes played contrasting roles in overland flow generation. The average amount of overland flow over the 7-week period was higher for the lysimeters with white ashes than for the control lysimeters (36.0 vs. 31.2 l), while the opposite was true for the lysimeters with black ashes (26.8 l). These differences in overland flow were associated with differences in TSS concentrations that were the opposite, averaging 11.7 and 20.4 g l-1 over the entire study period in the case of the lysimeters with white and black ashes, respectively. The overall TSS concentrations also suggested a marked role for the riparian strips but only in the case of the black ashes, dropping to 15.3 g l-1. In the case of the white ashes, the overall TSS concentrations were the same with as without the riparian strips.