Huyen Thanh Pham
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Huyen Thanh Pham has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Toan Thanh Dao
University of Transport and Communications
4 shared publications Toan Thanh Dao
Faculty of Electrical-Electronic Engineering, University of Transport and Communications, No. 3, Cau Giay Street, Lang Thuong Ward, Dong da District, Hanoi, Vietnam
3 shared publications- Bui Thanh Danh
Faculty of Mechanical Engineering, University of Transport and Communications, Vietnam
1 shared publication - Heisuke Sakai
School of Science and Engineering Kokushikan University 154–8515 Tokyo Japan
1 shared publication Loan Pham-Nguyen
School of Electronics and Telecommunications, Hanoi University of Science and Technology, No. 1, Dai Co Viet Street, Hai Ba Trung District, Hanoi 10000, Vietnam
1 shared publicationThang Vu Nguyen
Hanoi University of Science and Technology
1 shared publication
Latest Publications
- Open Access
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 14, 172256-172268
Measurement-Driven Verilog-A Modeling of a Non-Resonant Flexible PZT/PVDF Footstep Energy Harvester
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 14, 172256-172268
Open AccessMeasurement-Driven Verilog-A Modeling of a Non-Resonant Flexible PZT/PVDF Footstep Energy Harvester
- Open Access
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 14, 173822-173838
A Branch-Isolated 2S2P PZT–PDMS/SWCNT–N66 Piezoelectric Energy-Harvesting Module for Smart Transportation Sensors
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 14, 173822-173838
Open AccessA Branch-Isolated 2S2P PZT–PDMS/SWCNT–N66 Piezoelectric Energy-Harvesting Module for Smart Transportation Sensors
- Open Access
- 15 February 2025
- Published by University of Transport and Communications in Transport and Communications Science Journal
- Vol. 76 (2) , 187-197
Thiết kế IC khuếch đại thuật toán công suất thấp, độ ổn định nhiễu cao sử dụng công nghệ GPDK045
Thiết kế mạch tích hợp (IC) khuếch đại công suất thấp là một hướng nghiên cứu quan trọng trong kỹ thuật điện tử, đặc biệt là cho các thiết bị đeo, hệ thống thu thập dữ liệu và các ứng dụng thu thập năng lượng liên tục. Trong quá trình thiết kế vi mạch, một tập hợp các tệp được sử dụng trong ngành công nghiệp bán dẫn để mô hình hóa quy trình chế tạo, hỗ trợ các công cụ thiết kế IC, được gọi là bộ công cụ thiết kế quy trình (PDK). Có thể nói, PDK đóng vai trò quan trọng bậc nhất trong quá trình thiết kế; tới nay, PDK được phát triển bởi nhiều công ty và cải tiến từ kích thước vài trăm nanomet đến vài nanomet. Trong số đó, gpdk045 được sử dụng rộng rãi trong các nghiên cứu học thuật và công nghiệp. Chính vì vậy, chúng tôi sử dụng công nghệ 45 nm này để thiết kế vi mạch khuếch đại thuật toán công suất thấp, độ ổn định nhiễu cao. Kết quả mô phỏng cho thấy công suất tiêu thụ toàn mạch là 0,84 mW, hệ số nén đồng pha CMRR đạt 56,4 dB và hệ số loại trừ nhiễu nguồn PSRR đạt 126,4 dB ở tần số thấp dưới 1 kHz. Những kết quả này cho thấy Op-amp được đề xuất trong nghiên cứu này có thể được sử dụng để tạo ra các cảm biến tích cực cho việc thu thập năng lượng từ bước chân hoặc đo nhịp tim
- 15 February 2025
- Published by University of Transport and Communications in Transport and Communications Science Journal
- Vol. 76 (2) , 187-197
Open AccessThiết kế IC khuếch đại thuật toán công suất thấp, độ ổn định nhiễu cao sử dụng công nghệ GPDK045
Thiết kế mạch tích hợp (IC) khuếch đại công suất thấp là một hướng nghiên cứu quan trọng trong kỹ thuật điện tử, đặc biệt là cho các thiết bị đeo, hệ thống thu thập dữ liệu và các ứng dụng thu thập năng lượng liên tục. Trong quá trình thiết kế vi mạch, một tập hợp các tệp được sử dụng trong ngành công nghiệp bán dẫn để mô hình hóa quy trình chế tạo, hỗ trợ các công cụ thiết kế IC, được gọi là bộ công cụ thiết kế quy trình (PDK). Có thể nói, PDK đóng vai trò quan trọng bậc nhất trong quá trình thiết kế; tới nay, PDK được phát triển bởi nhiều công ty và cải tiến từ kích thước vài trăm nanomet đến vài nanomet. Trong số đó, gpdk045 được sử dụng rộng rãi trong các nghiên cứu học thuật và công nghiệp. Chính vì vậy, chúng tôi sử dụng công nghệ 45 nm này để thiết kế vi mạch khuếch đại thuật toán công suất thấp, độ ổn định nhiễu cao. Kết quả mô phỏng cho thấy công suất tiêu thụ toàn mạch là 0,84 mW, hệ số nén đồng pha CMRR đạt 56,4 dB và hệ số loại trừ nhiễu nguồn PSRR đạt 126,4 dB ở tần số thấp dưới 1 kHz. Những kết quả này cho thấy Op-amp được đề xuất trong nghiên cứu này có thể được sử dụng để tạo ra các cảm biến tích cực cho việc thu thập năng lượng từ bước chân hoặc đo nhịp tim
- Open Access
- 17 May 2023
- Published by MDPI AG in Micromachines
- Vol. 14 (5) , 1058
A High-Reliability Piezoelectric Tile Transducer for Converting Bridge Vibration to Electrical Energy for Smart Transportation
Piezoelectric energy transducers offer great potential for converting the vibrations of pedestrian footsteps or cars moving on a bridge or road into electricity. However, existing piezoelectric energy-harvesting transducers are limited by their poor durability. In this paper, to enhance this durability, a piezoelectric energy transducer with a flexible piezoelectric sensor is fabricated in a tile protype with indirect touch points and a protective spring. The electrical output of the proposed transducer is examined as a function of pressure, frequency, displacement, and load resistance. The maximum output voltage and maximum output power obtained were 6.8 V and 4.5 mW, respectively, at a pressure of 70 kPa, a displacement of 2.5 mm, and a load resistance of 15 kΩ. The designed structure limits the risk of destroying the piezoelectric sensor during operation. The harvesting tile transducer can work properly even after 1000 cycles. Furthermore, to demonstrate its practical applications, the tile was placed on the floor of an overpass and a walking tunnel. Consequently, it was observed that the electrical energy harvested from the pedestrian footsteps could power an LED light fixture. The findings suggest that the proposed tile offers promise with respect to harvesting energy produced during transportation.
- 17 May 2023
- Published by MDPI AG in Micromachines
- Vol. 14 (5) , 1058
Open AccessA High-Reliability Piezoelectric Tile Transducer for Converting Bridge Vibration to Electrical Energy for Smart Transportation
Piezoelectric energy transducers offer great potential for converting the vibrations of pedestrian footsteps or cars moving on a bridge or road into electricity. However, existing piezoelectric energy-harvesting transducers are limited by their poor durability. In this paper, to enhance this durability, a piezoelectric energy transducer with a flexible piezoelectric sensor is fabricated in a tile protype with indirect touch points and a protective spring. The electrical output of the proposed transducer is examined as a function of pressure, frequency, displacement, and load resistance. The maximum output voltage and maximum output power obtained were 6.8 V and 4.5 mW, respectively, at a pressure of 70 kPa, a displacement of 2.5 mm, and a load resistance of 15 kΩ. The designed structure limits the risk of destroying the piezoelectric sensor during operation. The harvesting tile transducer can work properly even after 1000 cycles. Furthermore, to demonstrate its practical applications, the tile was placed on the floor of an overpass and a walking tunnel. Consequently, it was observed that the electrical energy harvested from the pedestrian footsteps could power an LED light fixture. The findings suggest that the proposed tile offers promise with respect to harvesting energy produced during transportation.
- 1 October 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 121-126
A low power complementary organic double-edge triggered D flip-flop with variable threshold voltage transistors
Some organic double-edge triggered D flip-flops were designed with modeled organic thin-film transistors (OTFTs) and evaluated. The simulation results indicated that the circuit power consumption could be saved 20 times with the appropriate structure composing N-channel switches and TG-based MUX 2:1. In order to reduce consumption energy more deeply, the balance in the charge mobility of each transistor type needs to be set in complementary circuits. One of effective ways is varying the threshold voltage of either P-type or N-type transistors. In this work, the threshold voltage of the P-type elements have been tuned from -4.4 to 4.6 V to determine the optimal value for minimizing power dissipation of the circuit and maximizing its performance. At the optimal Vth, p of -0.9 V, the circuit parameters are rise time, fall time, delay clock-to-Q and power dissipation of 57 ns, 8 ns, 52 ns, and 835 nW, respectively, at the supply voltage of 10 V and the clock pulse frequency of 1 kHz.
- 1 October 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 121-126
A low power complementary organic double-edge triggered D flip-flop with variable threshold voltage transistors
Some organic double-edge triggered D flip-flops were designed with modeled organic thin-film transistors (OTFTs) and evaluated. The simulation results indicated that the circuit power consumption could be saved 20 times with the appropriate structure composing N-channel switches and TG-based MUX 2:1. In order to reduce consumption energy more deeply, the balance in the charge mobility of each transistor type needs to be set in complementary circuits. One of effective ways is varying the threshold voltage of either P-type or N-type transistors. In this work, the threshold voltage of the P-type elements have been tuned from -4.4 to 4.6 V to determine the optimal value for minimizing power dissipation of the circuit and maximizing its performance. At the optimal Vth, p of -0.9 V, the circuit parameters are rise time, fall time, delay clock-to-Q and power dissipation of 57 ns, 8 ns, 52 ns, and 835 nW, respectively, at the supply voltage of 10 V and the clock pulse frequency of 1 kHz.
- 12 November 2016
- Published by Springer Nature
- p. 452-459
Performance Evaluation of SAR ADC with Organic Semiconductor
- 12 November 2016
- Published by Springer Nature
- p. 452-459
Performance Evaluation of SAR ADC with Organic Semiconductor
- Open Access
- 15 March 2016
- Published by Wiley in Active and Passive Electronic Components
- Vol. 2016, 1-11
Design and Simulation of a 6-Bit Successive-Approximation ADC Using Modeled Organic Thin-Film Transistors
We have demonstrated a method for using proper models of pentacene P-channel and fullerene N-channel thin-film transistors (TFTs) in order to design and simulate organic integrated circuits. Initially, the transistors were fabricated, and we measured their main physical and electrical parameters. Then, these organic TFTs (OTFTs) were modeled with support of an organic process design kit (OPDK) added in Cadence. The key specifications of the modeled elements were extracted from measured data, whereas the fitting ones were elected to replicate experimental curves. The simulating process proves that frequency responses of the TFTs cover all biosignal frequency ranges; hence, it is reasonable to deploy the elements to design integrated circuits used in biomedical applications. Complying with complementary rules, the organic circuits work properly, including logic gates, flip-flops, comparators, and analog-to-digital converters (ADCs) as well. The proposed successive-approximation-register (SAR) ADC consumes a power of 883.7 µW and achieves an ENOB of 5.05 bits, a SNR of 32.17 dB at a supply voltage of 10 V, and a sampling frequency of about 2 KHz.
- 15 March 2016
- Published by Wiley in Active and Passive Electronic Components
- Vol. 2016, 1-11
Open AccessDesign and Simulation of a 6-Bit Successive-Approximation ADC Using Modeled Organic Thin-Film Transistors
We have demonstrated a method for using proper models of pentacene P-channel and fullerene N-channel thin-film transistors (TFTs) in order to design and simulate organic integrated circuits. Initially, the transistors were fabricated, and we measured their main physical and electrical parameters. Then, these organic TFTs (OTFTs) were modeled with support of an organic process design kit (OPDK) added in Cadence. The key specifications of the modeled elements were extracted from measured data, whereas the fitting ones were elected to replicate experimental curves. The simulating process proves that frequency responses of the TFTs cover all biosignal frequency ranges; hence, it is reasonable to deploy the elements to design integrated circuits used in biomedical applications. Complying with complementary rules, the organic circuits work properly, including logic gates, flip-flops, comparators, and analog-to-digital converters (ADCs) as well. The proposed successive-approximation-register (SAR) ADC consumes a power of 883.7 µW and achieves an ENOB of 5.05 bits, a SNR of 32.17 dB at a supply voltage of 10 V, and a sampling frequency of about 2 KHz.
- 1 October 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 21621020,p. 383-386
Reduction of operating voltage in organic transistor and CMOS circuit utilizing high-k dielectric
Employment of high-k dielectric is one of the most important strategies to reduce operating voltage of an integrated circuit. This paper demonstrates experiments on organic FET and CMOS circuit where the dielectric layer was constructed of P(VDF-TrFE) and PS polymer dielectric. The dielectric constant of compound dielectric increased about three times in comparison with that of pristine PS. This contributes into lowering the operating voltage transistor circuit. The experimental results indicated that high-k dielectric of P(VDF-TrFE) and PS may be suitable for flexible low-power organic electronics.
- 1 October 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 21621020,p. 383-386
Reduction of operating voltage in organic transistor and CMOS circuit utilizing high-k dielectric
Employment of high-k dielectric is one of the most important strategies to reduce operating voltage of an integrated circuit. This paper demonstrates experiments on organic FET and CMOS circuit where the dielectric layer was constructed of P(VDF-TrFE) and PS polymer dielectric. The dielectric constant of compound dielectric increased about three times in comparison with that of pristine PS. This contributes into lowering the operating voltage transistor circuit. The experimental results indicated that high-k dielectric of P(VDF-TrFE) and PS may be suitable for flexible low-power organic electronics.