Chris Saunders
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Chris Saunders has a total of 31 co-authors. Here are the top co-authors by number of shared publications:
- John Milton Fielke
STEM, University of South Australia, Mawson Lakes Campus, Adelaide, SA 5095, Australia
16 shared publications - Mustafa Ucgul
Faculty of Science and Engineering, Southern Cross University, Lismore, NSW 2084, Australia
12 shared publications - Jack M. A. Desbiolles
CSTEM, University of South Australia, Adelaide, SA 5000, Australia
4 shared publications - Ali Khosravani
UniSA STEM, University of South Australia, Mawson Lakes, SA 5095, Australia
2 shared publications G. Shahgoli
2 shared publicationsGholamhossein Shahgoli
2 shared publications
Latest Publications
- Open Access
- 26 May 2025
- Published by Elsevier in Soil and Tillage Research
- Vol. 253
Pilot study into the performance of inclusion plates used in deep ripping
- 26 May 2025
- Published by Elsevier in Soil and Tillage Research
- Vol. 253
Open AccessPilot study into the performance of inclusion plates used in deep ripping
- Open Access
- 13 January 2023
- Published by MDPI AG in Agriculture
- Vol. 13 (1) , 206
Prediction of Single Disc Seeding System Forces, Using a Semi-Analytical and Discrete Element Method (DEM)
There is a rising interest amongst Australian farmers to use disc seeders due to their ability to operate in high residue conditions and at higher speeds, commonly in the range of 12 to 15 km h−1. This paper reports on developing an analytical and discrete element method (DEM) force prediction model suited to a rotating flat disc blade operating at different sweep and tilt angles. To validate the models, field experiments were carried out with a flat disc blade at two tilt angles of 0 and 20° and four sweep angles of 6, 26, 45 and 90° in sandy soil. An analytical approach was developed following an experimental investigation that showed that only the forward portion of the disc blade is actively involved in generating soil failure, while the magnitude of this active portion of the soil-disc interface varied with sweep angle. The predicted active proportions correlated well with the experimental observations. As applying different sweep angles affects the direction of soil movement relative to the disc face, the directions of the friction and resultant forces at different sweep and tilt angles were determined. The equation of soil acceleration force was adapted to account for different sweep angles. Results showed that the predicted force fits relatively well with the measured data at 90, 45 and 26° sweep angle, while the low correlation between predicted and measured force at 6° sweep angle was due to the scrubbing reaction force not accounted for in the model. Results also showed that a better coefficient of determination (R2 = 0.93) was obtained between DEM vs. test results compared to the analytical model predictions (R2 = 0.86), particularly for predicting side forces. It was found from the study that both the developed analytical approach and DEM model enabled the prediction of soil forces at different sweep and tilt angles acting on a flat disc blade, which can assist in optimising disc design to lower the specific resistance.
- 13 January 2023
- Published by MDPI AG in Agriculture
- Vol. 13 (1) , 206
Open AccessPrediction of Single Disc Seeding System Forces, Using a Semi-Analytical and Discrete Element Method (DEM)
There is a rising interest amongst Australian farmers to use disc seeders due to their ability to operate in high residue conditions and at higher speeds, commonly in the range of 12 to 15 km h−1. This paper reports on developing an analytical and discrete element method (DEM) force prediction model suited to a rotating flat disc blade operating at different sweep and tilt angles. To validate the models, field experiments were carried out with a flat disc blade at two tilt angles of 0 and 20° and four sweep angles of 6, 26, 45 and 90° in sandy soil. An analytical approach was developed following an experimental investigation that showed that only the forward portion of the disc blade is actively involved in generating soil failure, while the magnitude of this active portion of the soil-disc interface varied with sweep angle. The predicted active proportions correlated well with the experimental observations. As applying different sweep angles affects the direction of soil movement relative to the disc face, the directions of the friction and resultant forces at different sweep and tilt angles were determined. The equation of soil acceleration force was adapted to account for different sweep angles. Results showed that the predicted force fits relatively well with the measured data at 90, 45 and 26° sweep angle, while the low correlation between predicted and measured force at 6° sweep angle was due to the scrubbing reaction force not accounted for in the model. Results also showed that a better coefficient of determination (R2 = 0.93) was obtained between DEM vs. test results compared to the analytical model predictions (R2 = 0.86), particularly for predicting side forces. It was found from the study that both the developed analytical approach and DEM model enabled the prediction of soil forces at different sweep and tilt angles acting on a flat disc blade, which can assist in optimising disc design to lower the specific resistance.
- Open Access
- 13 January 2023
- Published by MDPI AG in Agriculture
- Vol. 13 (1) , 202
Prediction of Single Disc Seeding System Forces, Using a Semi-Analytical and Discrete Element Method (DEM) Considering Rotation Effects
Disc seeders are commonly used in no-till farming systems, and their performance evaluation generally rely on expensive and time-consuming field experiments. Mathematical models can help speed up force-related evaluations and improve the understanding of soil-disc interactions, to assist the performance optimisation processes. Previous analytical force prediction models of disc blades have not accounted for the free rotation aspect of the disc blade. This paper develops an analytical force prediction model from the wide blade failure theory adapted to suit rotating flat disc blades operating at different sweep and tilt angles and compares predictions with Discrete Element Method (DEM) simulations. To validate the two models, experiments were performed on a remoulded sandy soil condition using a rotating flat disc set at two tilt angles of 0 and 20 and four sweep angles of 6, 26, 45 and 90° the 3-dimensional force components of draught, vertical and side forces were measured. Results showed a higher coefficient of determination (R2 = 0.95) was obtained with analytical model predictions compared to DEM predictions (R2 = 0.85) for their agreement with the test results. It was found that both the developed analytical approach and the DEM model can be used to predict tillage forces at different sweep and tilt angles acting on a rotating flat disc blade.- 13 January 2023
- Published by MDPI AG in Agriculture
- Vol. 13 (1) , 202
Open AccessPrediction of Single Disc Seeding System Forces, Using a Semi-Analytical and Discrete Element Method (DEM) Considering Rotation Effects
Disc seeders are commonly used in no-till farming systems, and their performance evaluation generally rely on expensive and time-consuming field experiments. Mathematical models can help speed up force-related evaluations and improve the understanding of soil-disc interactions, to assist the performance optimisation processes. Previous analytical force prediction models of disc blades have not accounted for the free rotation aspect of the disc blade. This paper develops an analytical force prediction model from the wide blade failure theory adapted to suit rotating flat disc blades operating at different sweep and tilt angles and compares predictions with Discrete Element Method (DEM) simulations. To validate the two models, experiments were performed on a remoulded sandy soil condition using a rotating flat disc set at two tilt angles of 0 and 20 and four sweep angles of 6, 26, 45 and 90° the 3-dimensional force components of draught, vertical and side forces were measured. Results showed a higher coefficient of determination (R2 = 0.95) was obtained with analytical model predictions compared to DEM predictions (R2 = 0.85) for their agreement with the test results. It was found that both the developed analytical approach and the DEM model can be used to predict tillage forces at different sweep and tilt angles acting on a rotating flat disc blade. - 1 August 2018
- Published by Elsevier in Computers and Electronics in Agriculture
- Vol. 151, 1-10
Analyzing the mixing performance of a rotary spader using digital image processing and discrete element modelling (DEM)
- 1 August 2018
- Published by Elsevier in Computers and Electronics in Agriculture
- Vol. 151, 1-10
Analyzing the mixing performance of a rotary spader using digital image processing and discrete element modelling (DEM)
- 1 May 2018
- Published by Elsevier in Biosystems Engineering
- Vol. 169, 199-208
Comparison of the discrete element and finite element methods to model the interaction of soil and tool cutting edge
- 1 May 2018
- Published by Elsevier in Biosystems Engineering
- Vol. 169, 199-208
Comparison of the discrete element and finite element methods to model the interaction of soil and tool cutting edge
- 1 August 2017
- Published by Elsevier in Biosystems Engineering
- Vol. 160, 140-153
Discrete element modelling of top soil burial using a full scale mouldboard plough under field conditions
- 1 August 2017
- Published by Elsevier in Biosystems Engineering
- Vol. 160, 140-153
Discrete element modelling of top soil burial using a full scale mouldboard plough under field conditions
- 1 March 2017
- Published by Elsevier in Biosystems Engineering
- Vol. 155, 44-54
Discrete element modelling of tillage forces and soil movement of a one-third scale mouldboard plough
- 1 March 2017
- Published by Elsevier in Biosystems Engineering
- Vol. 155, 44-54
Discrete element modelling of tillage forces and soil movement of a one-third scale mouldboard plough
- 1 January 2017
- Published by American Society of Agricultural and Biological Engineers (ASABE) in Applied Engineering in Agriculture
- Vol. 33 (5) , 695-701
Reducing the Integrated Harrington Seed Destructor Power Requirements through Chaff Fraction Optimization
Abstract.: : Mechanical weed seed destruction during harvest is an effective method of reducing viable weed seed inputs to the seedbank. The commercialized Integrated Harrington Seed Destructor (iHSD) was developed for destroying weed seeds contained in the chaff residue exiting the harvester. Considered state-of-the-art in harvest weed seed control (HWSC), weed seed destruction is achieved without crop residue loss (burning or removal) and therefore, the iHSD is well suited to use in conservation cropping systems. However, as the iHSD is powered directly by the harvester its power draw impacts harvester performance. The objectives of this study were to determine the iHSD mill power requirements for effective weed seed destruction and to identify opportunities for decreasing these requirements. Using a torque-arm arrangement, the power requirements of an iHSD mill test rig powered by a PTO drive were measured. Wheat chaff containing a known amount of annual ryegrass () seed was passed through decreasing aperture sized sieves to obtain chaff size and seed distributions. The standard power demand to process chaff was ~54 kW, restricting the use of this system to large capacity harvesters. It was found that annual ryegrass seeds were concentrated in the chaff fraction passing through a 3 mm sieve. The power demand for processing this refined fraction was reduced by approximately a third to ~36kW. Efficient mechanical means to refine the chaff fraction to focus on the weed seed portion should be investigated. Keywords: Agricultural engineering, Conservation cropping, Efficiency, Harvest weed seed control, Herbicide resistance, Mechanical weed seed destruction,
- 1 January 2017
- Published by American Society of Agricultural and Biological Engineers (ASABE) in Applied Engineering in Agriculture
- Vol. 33 (5) , 695-701
Reducing the Integrated Harrington Seed Destructor Power Requirements through Chaff Fraction Optimization
Abstract.: : Mechanical weed seed destruction during harvest is an effective method of reducing viable weed seed inputs to the seedbank. The commercialized Integrated Harrington Seed Destructor (iHSD) was developed for destroying weed seeds contained in the chaff residue exiting the harvester. Considered state-of-the-art in harvest weed seed control (HWSC), weed seed destruction is achieved without crop residue loss (burning or removal) and therefore, the iHSD is well suited to use in conservation cropping systems. However, as the iHSD is powered directly by the harvester its power draw impacts harvester performance. The objectives of this study were to determine the iHSD mill power requirements for effective weed seed destruction and to identify opportunities for decreasing these requirements. Using a torque-arm arrangement, the power requirements of an iHSD mill test rig powered by a PTO drive were measured. Wheat chaff containing a known amount of annual ryegrass () seed was passed through decreasing aperture sized sieves to obtain chaff size and seed distributions. The standard power demand to process chaff was ~54 kW, restricting the use of this system to large capacity harvesters. It was found that annual ryegrass seeds were concentrated in the chaff fraction passing through a 3 mm sieve. The power demand for processing this refined fraction was reduced by approximately a third to ~36kW. Efficient mechanical means to refine the chaff fraction to focus on the weed seed portion should be investigated. Keywords: Agricultural engineering, Conservation cropping, Efficiency, Harvest weed seed control, Herbicide resistance, Mechanical weed seed destruction,
- Open Access
- 1 September 2015
- Published by Elsevier in Information Processing in Agriculture
- Vol. 2 (2) , 130-141
Defining the effect of sweep tillage tool cutting edge geometry on tillage forces using 3D discrete element modelling
- 1 September 2015
- Published by Elsevier in Information Processing in Agriculture
- Vol. 2 (2) , 130-141
Open AccessDefining the effect of sweep tillage tool cutting edge geometry on tillage forces using 3D discrete element modelling
- 1 May 2015
- Published by Elsevier in Biosystems Engineering
- Vol. 133, 56-63
A Mastercurve to predict annual ryegrass (Lolium rigidum) seed devitalisation when exposed to multiple single sided impacts
- 1 May 2015
- Published by Elsevier in Biosystems Engineering
- Vol. 133, 56-63
A Mastercurve to predict annual ryegrass (Lolium rigidum) seed devitalisation when exposed to multiple single sided impacts