Majid Rahimpour
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Majid Rahimpour has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
Kourosh Qaderi
Department of Water Science and Engineering, Faculty of Agriculture, Shahid Bahonar University of Kerman, Kerman, Iran
4 shared publications- Ali Tavakoli
Department of Applied Mathematics, University of Mazandaran, Babolsar, Iran
3 shared publications - Mahmoud Faghfour Maghrebi
Ferdowsi University of Mashhad
3 shared publications Mohamad Reza Madadi
Department of Water Science and Engineering, Faculty of Agriculture, University of Jiroft, Jiroft, Iran
3 shared publicationsMohammad Mehdi Ahmadi
Department of Water Science and Engineering, Faculty of Agriculture, Shahid Bahonar University of Kerman, Kerman, Iran
3 shared publications- Kourosh Qaderi
Department of Water Engineering, Shahid Bahonar University of Kerman, Kerman, Iran
2 shared publications
Latest Publications
- Open Access
- 13 January 2026
- Published by Springer Nature in Scientific Reports
- Vol. 16 (1)
New experimental configuration for investigation of debris accumulation effect on local scour at bridge pier and abutment
Debris accumulation around bridge piers and abutments threatens stability by intensifying scour and risking collapse. While the effects of debris on individual bridge components have been studied, the combined influence of debris in the presence of both pier and abutment remains underexplored. This study experimentally examines how debris shape, thickness, and pier-abutment distance affect local scour depth under clear-water conditions. Experiments were conducted in 8 m long, 0.8 m wide, and 0.6 m deep flume, filled with 15 cm of uniform sand (\({d}_{50}=0.83\) mm, \({\sigma }_{g}=1.5\)) and operated at a constant discharge of 30 l/s. Results showed that increasing the relative thickness of rectangular debris from 0.09 to 0.39 lead to a 41% increase in scour depth at the pier and 47% at the abutment. Reducing the pier-abutment distance from 0.2 to 0.1 caused an increase in scour depth by 21% and 16%, respectively. Thicker debris enhanced vortex intensity, resulting in deeper scouring. Among the tested shapes, rectangular debris caused the most significant scour, while triangular debris had the least effect. In all cases, maximum scour occurred at the abutment. These findings emphasize the practical significance of considering debris-structure interactions to improve bridge safety and resilience in engineering design.- 13 January 2026
- Published by Springer Nature in Scientific Reports
- Vol. 16 (1)
Open AccessNew experimental configuration for investigation of debris accumulation effect on local scour at bridge pier and abutment
Debris accumulation around bridge piers and abutments threatens stability by intensifying scour and risking collapse. While the effects of debris on individual bridge components have been studied, the combined influence of debris in the presence of both pier and abutment remains underexplored. This study experimentally examines how debris shape, thickness, and pier-abutment distance affect local scour depth under clear-water conditions. Experiments were conducted in 8 m long, 0.8 m wide, and 0.6 m deep flume, filled with 15 cm of uniform sand (\({d}_{50}=0.83\) mm, \({\sigma }_{g}=1.5\)) and operated at a constant discharge of 30 l/s. Results showed that increasing the relative thickness of rectangular debris from 0.09 to 0.39 lead to a 41% increase in scour depth at the pier and 47% at the abutment. Reducing the pier-abutment distance from 0.2 to 0.1 caused an increase in scour depth by 21% and 16%, respectively. Thicker debris enhanced vortex intensity, resulting in deeper scouring. Among the tested shapes, rectangular debris caused the most significant scour, while triangular debris had the least effect. In all cases, maximum scour occurred at the abutment. These findings emphasize the practical significance of considering debris-structure interactions to improve bridge safety and resilience in engineering design. - Open Access
Effects of Spatial Data Acquisition on Determination of a Gravel-Bed River Geomorphology
Bed irregularities of water bodies play a significant role in many hydraulic and river engineering experiments and models. Accurate measurement of river geomorphology requires great fieldwork effort. Optimizing the dataset size of measured points will reduce the time and costs involved. In this study, the geomorphology of a gravel bed river reach was measured using different spatial acquisition methods. Digital elevation models were created for each measurement method and the volumes of under/overestimation were calculated. The results show that the sampling methods had more effect on the accuracy of the interpolated geomorphology than the density of the measured points. By choosing an optimized sampling method, the measurement efforts decreased to less than 50%, with negligible errors of around 15 m3 and 10 m3 over and underestimation, respectively, in a water body area of around 2200 m2. These findings help to provide more accurate geomorphological data with less effort as inputs for experimental and numerical models to derive better results.
Open AccessEffects of Spatial Data Acquisition on Determination of a Gravel-Bed River Geomorphology
Bed irregularities of water bodies play a significant role in many hydraulic and river engineering experiments and models. Accurate measurement of river geomorphology requires great fieldwork effort. Optimizing the dataset size of measured points will reduce the time and costs involved. In this study, the geomorphology of a gravel bed river reach was measured using different spatial acquisition methods. Digital elevation models were created for each measurement method and the volumes of under/overestimation were calculated. The results show that the sampling methods had more effect on the accuracy of the interpolated geomorphology than the density of the measured points. By choosing an optimized sampling method, the measurement efforts decreased to less than 50%, with negligible errors of around 15 m3 and 10 m3 over and underestimation, respectively, in a water body area of around 2200 m2. These findings help to provide more accurate geomorphological data with less effort as inputs for experimental and numerical models to derive better results.
- Open Access
Experimental Study Demonstrating a Cost-Effective Approach for Generating 3D-Enhanced Models of Sediment Flushing Cones Using Model-Based SFM Photogrammetry
Accurate measurements of sediment flushing cone geometry (SFCG) are essential for determining sediment removal efficiency in reservoirs. SFCG measurements are related to the point-to-point height that affects bathymetry accuracy, and they are used to develop a digital elevation model (DEM). Conventional bathymetry monitoring techniques require a longer time for data processing and output data with insufficient accuracy despite being inexpensive and simple. In the current research, a close-range photogrammetric method called the structure from motion (SFM) method was investigated to determine the SFCG in an experimental study. The regular geometric shape of a cube was used to verify the SFM. Additionally, measurements between model control points (MCPs) on the flushed sediment bed were compared with those from the SFM method. The results indicated that the calculated SFM values were consistent with the measured values. To determine the SFCG, two sets of images were captured with 70% average overlapping before and after the completion of each test. After processing and post-processing via the SFM tool AgiSoft Metashape, a georeferenced 3D model was achieved. The accuracy of the surveyed data in terms of the dimensions, cross-sections, and temporal developments of the sediment flushing cone was investigated to verify the SFM method. Finally, the results revealed good agreement ( and average error of 0.03–0.74 mm) between the DEMs created by the SFM method and the actual model.Open AccessExperimental Study Demonstrating a Cost-Effective Approach for Generating 3D-Enhanced Models of Sediment Flushing Cones Using Model-Based SFM Photogrammetry
Accurate measurements of sediment flushing cone geometry (SFCG) are essential for determining sediment removal efficiency in reservoirs. SFCG measurements are related to the point-to-point height that affects bathymetry accuracy, and they are used to develop a digital elevation model (DEM). Conventional bathymetry monitoring techniques require a longer time for data processing and output data with insufficient accuracy despite being inexpensive and simple. In the current research, a close-range photogrammetric method called the structure from motion (SFM) method was investigated to determine the SFCG in an experimental study. The regular geometric shape of a cube was used to verify the SFM. Additionally, measurements between model control points (MCPs) on the flushed sediment bed were compared with those from the SFM method. The results indicated that the calculated SFM values were consistent with the measured values. To determine the SFCG, two sets of images were captured with 70% average overlapping before and after the completion of each test. After processing and post-processing via the SFM tool AgiSoft Metashape, a georeferenced 3D model was achieved. The accuracy of the surveyed data in terms of the dimensions, cross-sections, and temporal developments of the sediment flushing cone was investigated to verify the SFM method. Finally, the results revealed good agreement ( and average error of 0.03–0.74 mm) between the DEMs created by the SFM method and the actual model. - 20 February 2020
- Published by Taylor & Francis in Marine Georesources & Geotechnology
- Vol. 39 (4) , 459-470
Scour at side by side pier and abutment with debris accumulation
This is the first attempt to study the effect of debris on the scour at side by side pier and abutment. A large set of experimental tests was carried out at the hydraulic laboratory of Shahid Bahonar University of Kerman, in a tilting flume with 10 m length, 0.8 m width and 0.5 m depth. Effect of debris shape, thickness, position, length, and the distance between abutment and pier was investigated. Results revealed that the main factor in deepening and developing of scour hole is the distance between pier and abutment, lp, by increasing the distance, the scour depth primarily increases and then decreases to eventually reach the scour depth at single pier. The observations indicated the significant effect of debris on dimensions of scour hole, for example, increasing the debris thickness and length increased the maximum scour depth up to 30 and 8%, respectively. Based on the measured data, some improvements were made on the existing equations and a set of new relations was presented to estimate the side by side pier and abutment scour depth.
- 20 February 2020
- Published by Taylor & Francis in Marine Georesources & Geotechnology
- Vol. 39 (4) , 459-470
Scour at side by side pier and abutment with debris accumulation
This is the first attempt to study the effect of debris on the scour at side by side pier and abutment. A large set of experimental tests was carried out at the hydraulic laboratory of Shahid Bahonar University of Kerman, in a tilting flume with 10 m length, 0.8 m width and 0.5 m depth. Effect of debris shape, thickness, position, length, and the distance between abutment and pier was investigated. Results revealed that the main factor in deepening and developing of scour hole is the distance between pier and abutment, lp, by increasing the distance, the scour depth primarily increases and then decreases to eventually reach the scour depth at single pier. The observations indicated the significant effect of debris on dimensions of scour hole, for example, increasing the debris thickness and length increased the maximum scour depth up to 30 and 8%, respectively. Based on the measured data, some improvements were made on the existing equations and a set of new relations was presented to estimate the side by side pier and abutment scour depth.
- Open Access
- 29 October 2019
- Published by Academy of Science of South Africa in Water SA
- Vol. 45 (4 October) , 685-690
Assessment of straight and meandering furrow irrigation strategies under different inflow rates
This paper reports the effect of straight furrow (SF) and meandering furrow (MF) irrigation strategies, as well as inflow rate, on infiltration and hydraulic parameters including advance time, recession time, and runoff hydrograph. The performance of SF and MF irrigation in terms of runoff ratio, deep percolation, and application efficiency was evaluated in 6 furrow fields at Shahid Bahonar University of Kerman, Iran. The required data were collected from the farm, consisting of free drainage furrows with length 70 m, top width 0.8 m, depth 0.25 m, and slope 0.2%. The advance and recession times were significantly longer in MF than SF irrigation. The infiltration was estimated by Lewis-Kostiakov equation. The infiltration coefficients were calculated: The values of k were higher and of a were lower in MF furrows than in SF furrows. The average runoff ratio and application efficiency for the SF irrigation events were 50.53% and 49.07%, respectively, while those of the MF irrigation events were 7.04% and 52.94%, respectively. Based on the results, the velocity of water advance in MF irrigation is decreased and, thus, the runoff, erosion losses, mass of fertilizer lost and surface water contamination were reduced. Using a lower inflow rate and appropriate irrigation time leads to better management outcomes in irrigation systems.
- 29 October 2019
- Published by Academy of Science of South Africa in Water SA
- Vol. 45 (4 October) , 685-690
Open AccessAssessment of straight and meandering furrow irrigation strategies under different inflow rates
This paper reports the effect of straight furrow (SF) and meandering furrow (MF) irrigation strategies, as well as inflow rate, on infiltration and hydraulic parameters including advance time, recession time, and runoff hydrograph. The performance of SF and MF irrigation in terms of runoff ratio, deep percolation, and application efficiency was evaluated in 6 furrow fields at Shahid Bahonar University of Kerman, Iran. The required data were collected from the farm, consisting of free drainage furrows with length 70 m, top width 0.8 m, depth 0.25 m, and slope 0.2%. The advance and recession times were significantly longer in MF than SF irrigation. The infiltration was estimated by Lewis-Kostiakov equation. The infiltration coefficients were calculated: The values of k were higher and of a were lower in MF furrows than in SF furrows. The average runoff ratio and application efficiency for the SF irrigation events were 50.53% and 49.07%, respectively, while those of the MF irrigation events were 7.04% and 52.94%, respectively. Based on the results, the velocity of water advance in MF irrigation is decreased and, thus, the runoff, erosion losses, mass of fertilizer lost and surface water contamination were reduced. Using a lower inflow rate and appropriate irrigation time leads to better management outcomes in irrigation systems.
- 15 July 2019
- Published by Taylor & Francis in Marine Georesources & Geotechnology
- Vol. 38 (8) , 911-922
The performance of collars on scour reduction at tandem piers aligned with different skew angles
Local scouring is a leading cause of bridge collapses. To protect bridges against local scouring, different countermeasures have been proposed and tested in the literature. In this study, the performance of collars was evaluated for scour reduction at two tandem piers aligned with four skew angles ( ) of with respect to flow direction. For this purpose, long duration tests were conducted with uniform sediments under clear-water conditions with flow intensities close to the threshold of sediment motion. The results showed that increasing the skew angle increased the scour depth, while the performance of collars for scour reduction decreased. The maximum and minimum scour depths occurred at skew angles of and respectively, around both the piers with and without collars. Analysis of the results indicated that the maximum scour depth at the upstream pier shifted to the downstream pier from and for the tandem piers with and without collars, respectively. In addition, as the skew angle increased, the equilibrium time of scour increased. Moreover, the performance of collars for scour reduction around the piers decreased over time.- 15 July 2019
- Published by Taylor & Francis in Marine Georesources & Geotechnology
- Vol. 38 (8) , 911-922
The performance of collars on scour reduction at tandem piers aligned with different skew angles
Local scouring is a leading cause of bridge collapses. To protect bridges against local scouring, different countermeasures have been proposed and tested in the literature. In this study, the performance of collars was evaluated for scour reduction at two tandem piers aligned with four skew angles ( ) of with respect to flow direction. For this purpose, long duration tests were conducted with uniform sediments under clear-water conditions with flow intensities close to the threshold of sediment motion. The results showed that increasing the skew angle increased the scour depth, while the performance of collars for scour reduction decreased. The maximum and minimum scour depths occurred at skew angles of and respectively, around both the piers with and without collars. Analysis of the results indicated that the maximum scour depth at the upstream pier shifted to the downstream pier from and for the tandem piers with and without collars, respectively. In addition, as the skew angle increased, the equilibrium time of scour increased. Moreover, the performance of collars for scour reduction around the piers decreased over time.- 6 June 2019
- Published by Springer Nature in Journal of Hydrodynamics
- Vol. 31 (5) , 986-998
Impacts of vegetation over bedforms on flow characteristics in gravel-bed rivers
- 6 June 2019
- Published by Springer Nature in Journal of Hydrodynamics
- Vol. 31 (5) , 986-998
Impacts of vegetation over bedforms on flow characteristics in gravel-bed rivers
- Open Access
- 1 January 2019
- Vol. 6 (1) , 25-31
Series and parallel pipelines system solutions using Regula Falsi method scripted in Mathematica
- 1 January 2019
- Vol. 6 (1) , 25-31
Open AccessSeries and parallel pipelines system solutions using Regula Falsi method scripted in Mathematica
- 13 July 2017
- Published by Springer Nature in Water Resources Management
- Vol. 31 (14) , 4633-4647
Improving the Pressurized Flushing Efficiency in Reservoirs: an Experimental Study
- 13 July 2017
- Published by Springer Nature in Water Resources Management
- Vol. 31 (14) , 4633-4647
Improving the Pressurized Flushing Efficiency in Reservoirs: an Experimental Study
- Open Access
- 14 June 2017
- Published by Elsevier in KSCE Journal of Civil Engineering
- Vol. 22 (4) , 1496-1505
Effect of Debris on Piers Group Scour: An Experimental Study
- 14 June 2017
- Published by Elsevier in KSCE Journal of Civil Engineering
- Vol. 22 (4) , 1496-1505
Open AccessEffect of Debris on Piers Group Scour: An Experimental Study