HTHailong Tang

Hailong Tang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Hailong Tang has a total of 30 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Multifidelity Simulation Research on the Low Reynolds Number Effect on the Engine Performance at Different Altitudes

    by Zihao Jia, Hailong Tang, Donghai Jin, Min Chen, Shulei Li, Xiaoheng Liu

    With the rapid development of unmanned aerial vehicles, the effect of the low Reynolds number on gas turbine performance and high-altitude endurance has received extensive attention. However, the existing three-dimensional component modeling cannot meet the design requirements of the whole engine level, and the accuracy and physical principles of the existing engine empirical correction cannot be guaranteed. Through the study of a single-shaft turbojet engine, this paper adopts a versatile and accurate coupling method, which combines the volume method and the full coupling method and conducts multifidelity simulation research on the zero-dimensional engine model and the three-dimensional component model. Then, based on the high-altitude test data, under typical operating conditions, compared with the existing empirical correction method in gasturb, the accuracy of the engine inlet flow, fuel flow, thrust, and exhaust gas temperature predicted by the volume-based fully coupled method is improved by 6.2%, 7.9%, 4.7%, and 11.4%, respectively. Next, as the flight altitude rises from 0 km to 21 km, the Reynolds number reduces, the working lines approach the surge lines, and the maximum mass flow rate and the efficiency of the engine components gradually decrease. In addition, in the flow field of the components, the thickness of the boundary layer increases, the shock wave intensity decreases, and the position moves forward. The core innovation of this article is that it provides a creative multifidelity evaluation method for gas turbines to effectively solve the problems of insufficient accuracy of the existing empirical correction methods and the inability of the component design to meet the gas turbine requirements in the study of the low Reynolds number effect at different altitudes, which significantly strengthens the connection among the component internal flow field information extraction, the component characteristics analysis, and the gas turbine performance matching. Moreover, it is conducive to the scientific design of the advanced unmanned aerial vehicles' power.


  • Laser-induced breakdown spectroscopy for quantitative and qualitative analysis of the ash fusion temperatures of coal in power plants

    by Wenhao Zhang, Zhuang Zhuo, Peng Lu, Jingqi Lu, Tengfei Sun, Jing Tang, Hailong Tang, Tao Zhou, Li Li

    The prediction of coal fusion characteristics and determination of slagging behaviour are of great significance to the operation of thermal power plants. The traditional method needs a long time to measure coal ash fusion temperatures (AFTs) by heating the coal ash cone. The purpose of this work is to predict the coal AFTs directly from coal rather than coal ash using Laser-Induced Breakdown Spectroscopy (LIBS). On the premise that ash content, volatile matter, fixed carbon and moisture are known on the air-dry base state, these four parameters are added into the model as generalized spectral (GS) variables to improve the accuracy of coal AFT prediction, in which the R2 of softening temperature (ST) and hemisphere temperature (HT) reached 0.9958 and 0.9856, the root-mean-square of cross-validation (RMSECV) reached 4.88 °C and 9.11 °C, and the root-mean-square of prediction (RMSEP) reached 8.15 °C and 11.3 °C, respectively. The trend relationships between the AFTs and the intensities (or ratio) of the spectral lines corresponding to individual elements of the LIBS spectrum were analysed. Then the variation trend of coal AFTs with specific element content (or ratio) is deduced qualitatively. We demonstrated that the model and scheme developed in this work can be applied in a real-time guiding role in the actual production process of the power plant.


  • Open Access

    Multi-state data-driven gas path analysis method

    by Shanxuan Tang, Hailong Tang, Min Chen


  • Open Access

    Research on Simulation and Performance Optimization of Mach 4 Civil Aircraft Propulsion Concept

    by Min Chen, Zihao Jia, Hailong Tang, Yi Xiao, Yonghang Yang, Feijia Yin

    Supersonic civil aircraft is of a promising area in the development of future civil transport, and aircraft propulsion system is one of the key issues which determine the success of the aircraft. To get a good conceptual design and performance investigation of the supersonic civil aircraft engine, in this article, a fast, versatile as well as trust-worthy numerical simulation platform was established to analyze the Mach 4 turbine-based combined cycle (TBCC) engine concept so as to be applied to the supersonic civil aircraft. First, a quick and accurate task requirement analysis module was newly established to analyze the mission requirement of the Mach 4 supersonic civil aircraft. Second, the TBCC engine performance simulation model was briefly presented and the number of engines on the supersonic civil aircraft was analyzed, considering single engine inoperative. Third, the Stone model and the DLR method were investigated to estimate the engine jet noise and the NOx emission of the Mach 4 supersonic civil aircraft. Finally, a multiobjective optimization tool made up of a response surface method and a genetic algorithm was developed to optimize the design parameters and the control law of the TBCC engine, in order to make the Mach 4 supersonic civil aircraft engine with better performance, lower noise, and lower emissions. The uniqueness of the developed analysis tool lies in that it affords a numerical simulation platform capable of investigating the task requirement analysis module of the supersonic civil aircraft, engine jet noise prediction model, and the NOx emission prediction model, as well as a multiobjective performance optimization tool, which is beneficial for the conceptual design and performance research of Mach 4 supersonic civil aircraft’s propulsion system.


  • Open Access

    Performance Analysis of a Three-Stream Adaptive Cycle Engine during Throttling

    by Min Chen, Jiyuan Zhang, Hailong Tang

    One advantage of the adaptive cycle engine (ACE) is its ability of throttling with constant airflow by the combined control of variable geometries, resulting in an improvement of spillage drag. However, the improvement is achieved at risk of a complex technical solution and control. This article investigates the selection scheme of variable geometries and engine configuration. It focuses on the performance of a three-stream ACE during throttling, whose configuration and control schedule are simpler than other types of ACEs. Five variable geometries are selected from seven available options through comparison analysis. The uninstalled thrust decreases from 100% to 60.36% during the subsonic throttling and to 59.81% during the supersonic throttling. Benefitting from the decreased spillage drag, the installed performance of the three-stream ACE is improved to some degree during throttling. This improvement is less than the result of a three-bypass ACE, whose configuration and control schedule are more complex. Thus, the three-stream ACE is a compromise design considering the technical risk and variable cycle characteristic, which is a better platform to verify the component technology and control schedule for the further research on a more complex type of ACE.


  • An Approach for Optimal Measurements Selection on Gas Turbine Engine Fault Diagnosis

    by Min Chen, Liang Quan Hu, Hailong Tang

    Gas path fault diagnosis plays an important role in guaranteeing safe, reliable and cost-effective operation for gas turbine engines. Measurements selection is among the most critical issues for diagnostic method implementation. In this paper, an integration approach for optimal measurements selection, which combines finger print diagrams analysis, health parameters correlation analysis, performance estimation uncertainty index analysis and fault cases validation based on genetic algorithm, has been proposed and applied to assess the health condition of a two-spool split flow turbofan in test bed. First, mathematical description of an engine gas path fault diagnosis process was given and the influence coefficient matrix was also calculated based on a well calibrated nonlinear engine performance simulation model. Second, the number of combination candidates was reduced from 782 to 256 and three measurements were picked out using the finger print diagrams analysis and the health parameters correlation analysis. Then, the number of the combination candidates was further narrowed down to 13 using the performance estimation uncertainty index analysis. A nonlinear genetic algorithm fault diagnosis method was applied to test the diagnostic ability of the remaining measurement candidates. Finally, an optimal measurement combination was worked out which demonstrated the effectiveness of the integration approach. This integration approach for optimal measurements selection is also applicable to other type of gas turbine engines.


  • Turbine-based combined cycle propulsion system integration concept design

    by Min Chen, Hailong Tang, Kun Zhang, Ouyang Hui, Yanjun Wang

    One of the most critical challenges for turbine-based combined cycle propulsion systems utilized in hypersonic civil aircrafts (Mach 0 to Mach 5) lies in guaranteeing the propulsion system to operate efficiently and stably along a very wide operating range. This has resulted in a need to investigate the matching restraints between the inlet and turbine-based combined cycle engine and nozzle from the integration point of view at the early stage of design. To get a good understanding of this integration concept design process, in this article, several basic design principles were first put forward. Next, a fast, versatile and trusted modular analysis tool for this concept design was developed and implemented. Third, several issues on this concept were analyzed including the design issues, the mechanisms of the variable geometries as well as the control schedules. Finally, a solution for the turbine-based combined cycle propulsion system was carried out and discussed. The results show that at least 11 total variables were required to be adopted in the variable cycle propulsion system to meet the basic mission requirements for Mach 5 civil airplane. How to guarantee these variable geometries function efficiently and reliably along the wide flight regime is one of the most critical technology challenges to make this concept feasible. The uniqueness of the developed analysis tool lies in that it affords a platform capable of investigating the design constraints and the matching relationships between the various propulsion components along a wide operating range, which is beneficial to predict the potential critical technological barriers at the early design stage.