Lanxin Sun
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Lanxin Sun has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Qun Zheng
College of Power and Energy Engineering, Harbin Engineering University, Harbin 150001, China
4 shared publications Yijin Li
Harbin Engineering University, Harbin 150001, China
3 shared publicationsLinjun Chen
1 shared publicationMingcong Luo
Harbin Engineering University, Harbin 150001, China
1 shared publication- Mingcong Luo
Harbin Engineering University, Harbin, Heilongjiang, China
1 shared publication Rakesh Bhargava
Foster Wheeler USA Corporation
1 shared publication
Latest Publications
- 1 February 2021
- Published by Elsevier in Chemical Engineering Science
- Vol. 230, 116185
Numerical simulation of single and two-phase flow across 90° vertical elbows
- 1 February 2021
- Published by Elsevier in Chemical Engineering Science
- Vol. 230, 116185
Numerical simulation of single and two-phase flow across 90° vertical elbows
- 1 May 2019
- Published by Elsevier in Journal of Wind Engineering and Industrial Aerodynamics
- Vol. 188, 90-101
Aerodynamic analysis of a step adjustment method for blade pitch of a VAWT
- 1 May 2019
- Published by Elsevier in Journal of Wind Engineering and Industrial Aerodynamics
- Vol. 188, 90-101
Aerodynamic analysis of a step adjustment method for blade pitch of a VAWT
- 30 November 2012
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 135 (1) , 012002
Numerical Simulation of a Complete Gas Turbine Engine With Wet Compression
In this paper, a thorough flow simulation of a small turbojet engine has been carried out to predict the engine performance as a result of water injected at the compressor inlet. Wet compression will not only change compressor performance characteristic map, but also has effects on both the combustor and the turbine sections. The match between the turbojet engine components, that is the compressor, combustor and turbine, will shift to a new operating point. In this paper, we present a steady-state numerical simulation of the entire gas turbine with wet compression in order to evaluate the effects on the gas turbine performance. Compared with the dry case, the results of wet cases show increased values of compressor compression ratios, turbine expansion ratios, intake mass flowrates, and engine thrusts including a decreased amount of specific fuel consumption. The wet compression reduces NOx production in the combustor, which is also simulated and with results presented. The study also indicates that the water mass flow rate and droplet diameter are key factors impacting the engine performance.
- 30 November 2012
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 135 (1) , 012002
Numerical Simulation of a Complete Gas Turbine Engine With Wet Compression
In this paper, a thorough flow simulation of a small turbojet engine has been carried out to predict the engine performance as a result of water injected at the compressor inlet. Wet compression will not only change compressor performance characteristic map, but also has effects on both the combustor and the turbine sections. The match between the turbojet engine components, that is the compressor, combustor and turbine, will shift to a new operating point. In this paper, we present a steady-state numerical simulation of the entire gas turbine with wet compression in order to evaluate the effects on the gas turbine performance. Compared with the dry case, the results of wet cases show increased values of compressor compression ratios, turbine expansion ratios, intake mass flowrates, and engine thrusts including a decreased amount of specific fuel consumption. The wet compression reduces NOx production in the combustor, which is also simulated and with results presented. The study also indicates that the water mass flow rate and droplet diameter are key factors impacting the engine performance.
- 7 April 2011
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 133 (8) , 082001
On the Behavior of Water Droplets When Moving Onto Blade Surface in a Wet Compression Transonic Compressor
The process of wet compression in an axial compressor is an intricate two-phase flow involving not only heat and mass transfer processes but also droplet breakup and even formation of discontinuous water film on the blade surface and then breaking into droplets. In this paper, the droplet-wall interactions are analyzed using the theory of spray wall impingement through two computational models for an isolated transonic compressor rotor (NASA rotor 37). Model 1, representing spread phenomenon, assumes that all droplets impacting on the blade are trapped in the water film and subsequently released from its trailing edge and enter the wake region with an equivalent mass flow but bigger in diameter and smaller in number. Whereas, the model 2, representing splashing phenomenon, assumes that upon impacting on the blade, the droplets will breakup into many smaller ones. The three-dimensional flow simulation results of these two models are analyzed and compared in this paper.
- 7 April 2011
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 133 (8) , 082001
On the Behavior of Water Droplets When Moving Onto Blade Surface in a Wet Compression Transonic Compressor
The process of wet compression in an axial compressor is an intricate two-phase flow involving not only heat and mass transfer processes but also droplet breakup and even formation of discontinuous water film on the blade surface and then breaking into droplets. In this paper, the droplet-wall interactions are analyzed using the theory of spray wall impingement through two computational models for an isolated transonic compressor rotor (NASA rotor 37). Model 1, representing spread phenomenon, assumes that all droplets impacting on the blade are trapped in the water film and subsequently released from its trailing edge and enter the wake region with an equivalent mass flow but bigger in diameter and smaller in number. Whereas, the model 2, representing splashing phenomenon, assumes that upon impacting on the blade, the droplets will breakup into many smaller ones. The three-dimensional flow simulation results of these two models are analyzed and compared in this paper.
- 28 February 2011
- Published by Wiley in Journal of Turbomachinery
- Vol. 133 (3) , 031026
Understanding Effects of Wet Compression on Separated Flow Behavior in an Axial Compressor Stage Using CFD Analysis
The effects of wet compression on the flow field within a compressor stage, particularly in the presence of the separated flow region, are not fully understood. Numerical simulations of 3D compressible separated flows within a wet compression compressor stage are carried out using a computational fluid dynamics (CFD) program. Numerical computations of flow fields in a compressor cascade with wet compression assume that a separated region exist in the corner of the rotor blade suction surface and hub surface in the case of dry compression. Under different operating conditions and with wet compression, this study presents the changes in the extent of separated region on the flow channel surfaces, compression efficiency, pressure ratio and specific compression work, etc. Also, effects of factors such as droplet size, droplet temperature, and injected water flow rate on the compressor stage performance and flow field within compressor stage passage have been investigated. The results show that wet compression could weaken and eliminate the flow separation and then the efficiency and pressure ratio maintain a high level.
- 28 February 2011
- Published by Wiley in Journal of Turbomachinery
- Vol. 133 (3) , 031026
Understanding Effects of Wet Compression on Separated Flow Behavior in an Axial Compressor Stage Using CFD Analysis
The effects of wet compression on the flow field within a compressor stage, particularly in the presence of the separated flow region, are not fully understood. Numerical simulations of 3D compressible separated flows within a wet compression compressor stage are carried out using a computational fluid dynamics (CFD) program. Numerical computations of flow fields in a compressor cascade with wet compression assume that a separated region exist in the corner of the rotor blade suction surface and hub surface in the case of dry compression. Under different operating conditions and with wet compression, this study presents the changes in the extent of separated region on the flow channel surfaces, compression efficiency, pressure ratio and specific compression work, etc. Also, effects of factors such as droplet size, droplet temperature, and injected water flow rate on the compressor stage performance and flow field within compressor stage passage have been investigated. The results show that wet compression could weaken and eliminate the flow separation and then the efficiency and pressure ratio maintain a high level.
- 1 January 2009
- Published by ASME International
- p. 623-629
The Effect of Partial Admission on Multistage Radial Inflow Industrial Steam Turbine
Aerodynamic performances of a partial admission multistage radial inflow turbine are investigated with numerical simulation. A three-dimensional unsteady Reynolds-averaged Navier–Stokes solver closed by Baldwin-Lomax model is applied for the computations. The flow field features of the first stages with partial admission are analyzed and discussed. Detailed flow patterns of the partial admission radial turbine impeller are presented here in this paper.
- 1 January 2009
- Published by ASME International
- p. 623-629
The Effect of Partial Admission on Multistage Radial Inflow Industrial Steam Turbine
Aerodynamic performances of a partial admission multistage radial inflow turbine are investigated with numerical simulation. A three-dimensional unsteady Reynolds-averaged Navier–Stokes solver closed by Baldwin-Lomax model is applied for the computations. The flow field features of the first stages with partial admission are analyzed and discussed. Detailed flow patterns of the partial admission radial turbine impeller are presented here in this paper.