Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Jia Fu has a total of 52 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Dual-Anchor-Constrained Temperature Compensation Model for Laser Tracker Tooling Metrology Incorporating Multi-Material Thermal Expansion Mismatch

    by Dong Han, Weihui Lin, Hongyang Wei, Shilong Zhang, Wei Zhang, Jia Fu

    To address coordinate drift at reference points during laser tracker measurements of large-scale assembly jigs, caused by thermal expansion mismatches among multiple materials, anchor point limitations, and non-uniform temperature fields, by developing a dual-anchor-constrained temperature compensation model and a corresponding procedure for revising measurement point coordinates and input parameters. The model unifies the temperature compensation plate, the main frame, and the foundation into a displacement transfer relationship, using plate-frame and frame-foundation anchor points along with layered temperature differences to compute reference point thermal displacements hierarchically. Simulations and field measurements are conducted under uniform heating, longitudinal/transverse temperature gradients, and local heat source disturbances, comparing the proposed method with uncompensated, uniform-expansion, and single-anchor compensation approaches. The proposed method reduces the root-meansquare error (RMSE) from 0.342 mm to 0.070 mm, the maximum deviation from 0.686 mm to 0.141 mm, and the key-point spacing error to within 0.083 mm. Repeatability standard deviation is lowered to 0.004 mm. The method maintains stability with 7-9 sensors and under minor anchor point disturbances. This work provides a feasible temperature drift correction scheme for online inspection, periodic re-measurement, and high-precision transfer of assembly references in large-scale assembly jigs.

  • Open Access

    Constitutive Analysis and Hot Processing Maps of As-Cast ZM6 Magnesium Alloys

    by Hong Zhang, Jia Fu

    The constitutive analysis model and hot processing map of the ZM6 alloy across various deformation conditions were investigated during hot compression experiments. True stress-strain curves within 300–450 °C and 0.0001–0.1 s−1 were obtained from compression tests on a Gleeble-1500 platform. The results showed that higher strain rates (e.g., 0.1 s−1) induced pronounced work hardening, whereas high temperatures (300–400 °C) combined with low strain rates (10−4 s−1) promoted conditions conducive to dynamic recrystallization (DRX), leading to a softening tendency of steady-state flow stress. Additionally, a modified strain-compensated constitutive model was built for flow stress prediction. Material constants were plotted as fifth-order polynomial functions of strain (0.025–0.80) for precise stress predictions. The derived activation energy (Q = 182.38 kJ/mol) falls within the typical range for Mg-RE alloys. Leave-one-temperature-out cross-validation showed average AARE values of 7.2–9.8%, demonstrating the model’s interpolation capability and its sensitivity to extrapolation. Cross-validation within the training dataset showed reasonable consistency between experimental and predicted stresses (R > 0.997, AARE < 4.35%). Using the dynamic materials model, hot processing maps identified safe deformation zones and instability zones of the ZM6 alloy. Flow instability was observed at strain rates >0.01 s−1, particularly at low temperatures (300–350 °C). Optimal processing windows appeared in high-energy dissipation (η > 30%) regions, e.g., 400–450 °C/10−4–10−3 s−1. Optical microscopy confirmed that at high temperatures (≥400 °C) and low strain rates (≤0.001 s−1), a uniform, fine-grained, fully recrystallized structure can be obtained, whereas low temperatures (350 °C) and high strain rates (0.1 s−1) produce coarse elongated grains with limited DRX, consistent with the instability regime predicted by the processing maps. Under intermediate conditions (e.g., 400 °C, 0.01 s−1), a bimodal grain distribution indicates incomplete recrystallization. Although EBSD analysis was not performed in this study, the optical microstructures directly validate the predicted safe and unstable windows. Together, all these findings provide preliminary model-based guidance for optimizing hot working parameters to balance microstructural stability and processing efficiency.

  • PEDOT-based thermoelectric composites: Preparation, mechanism and applications

    by Jia Fu, Shilong Zhang, Lirong Liang, Chunyu Du, Zhenqiang Ye, Guangming Chen


  • Open Access

    Microstructure Evolution and Mechanical Properties of As-Cast and As-Compressed ZM6 Magnesium Alloys during the Two-Stage Aging Treatment Process

    by Jia Fu, Su Chen

    In the present study, different solid solution and aging processes of as-cast and as-compressed ZM6 (Mg2.6Nd0.4Zn0.4Zr) alloy were designed, and the microstructure and precipitation strengthening mechanisms were discussed. After the pre-aging treatment, a large amount of G.P. zones formed in the α-Mg matrix over the course of the subsequent secondary G.P. prescription, where the fine and dispersed Mg12(Nd,Zn) phases were precipitated at the grain boundaries. The pre-aging and secondary aging processes resulted in the Mg12(Nd,Zn) phase becoming globular, preventing grain boundary sliding and decreasing grain boundary diffusion. Meanwhile, precipitation phase â″(Mg3Nd) demonstrated a coherent relationship with the α-Mg matrix after the pre-aging process, and after the secondary aging phase, Mg12Nd increases and became semi-coherent in the matrix. Compared to an as-cast ZM6 alloy, the yield strength of the as-compressed ZM6 alloy increased sharply due to an increase in the yield strength that was proportional to the particle spacing, where the dislocation bypassed the second phase particle. Compared to the single-stage aging process, the two-stage aging process greatly improved the mechanical properties of both the as-cast and as-compressed ZM6 alloys. The difference between the as-cast and as-compressed states is that an as-compressed ZM6 alloy with more dislocations and twins has more dispersed precipitates in the G.P. zones after secondary aging, meaning that it is greatly strengthened after the two-stage aging treatment process.


  • Calculation of lattice vibrational and thermal properties of cadmium sulfide nanocrystal and growth preference of cadmium sulfide powder during microwave‐hydrothermal process

    by Jia Fu, Su Chen, Xing Liu

    CdS nanocrystal is investigated by first‐principles calculations and experiments. Based on phonon spectra, the wurtzite CdS structure is thermodynamically stable. Debye temperature, specific heat capacity and thermal expansion coefficient are calculated to be 221.51 K, 47.68 J·mol−1·K−1 and 1.95×10−4 K−1, respectively. Band gaps of CdS single crystal and monolayer CdS supercell calculated by GGA–mBJ function are 2.74 eV and 2.38 eV. CdS powder is synthesized by microwave‐hydrothermal process (140 °C + 15 min), with particle size ranging from 50 to 1000 nm. HRTEM shows the nanocrystal distance of 6.676 Å between the (0001) crystal faces and growth preference along the [002] direction. The band gap of CdS thin film evaluated by UV–Vis absorption spectra is 2.41 eV, close to 2.38 eV of monolayer supercell, which provides theoretical basis for CdS doping to improve photoanode performance of piezoelectric semiconductors.


  • Open Access

    Microstructure Evolution and Mechanical Properties of X6CrNiMoVNb11-2 Stainless Steel after Heat Treatment

    by Jia Fu, Chaoqi Xia

    X6CrNiMoVNb11-2 supermartensitic stainless steel, a special type of stainless steel, is commonly used in the production of gas turbine discs in liquid rocket engines and compressor disks in aero engines. By optimizing the parameters of the heat-treatment process, its mechanical properties are specially adjusted to meet the performance requirement in that particular practical application during the advanced composite casting-rolling forming process. The relationship between the microstructure and mechanical properties after quenching from 1040 °C and tempering at 300–670 °C was studied, where the yield strength, tensile strength, elongation and impact toughness under different cooling conditions are obtained by means of mechanical property tests. A certain amount of high-density nanophase precipitation is found in the martensite phase transformation through the heat treatment involved in the quenching and tempering processes, where M23C6 carbides are dispersed in lamellar martensite, with the close-packed Ni3Mo and Ni3Nb phases of high-density co-lattice nanocrystalline precipitation created during the tempering process. The ideal process parameters are to quench at 1040 °C in an oil-cooling medium and to temper at 650 °C by air-cooling; final hardness is averaged about 313 HV, with an elongation of 17.9%, the cross-area reduction ratio is 52%, and the impact toughness is about 65 J, respectively. Moreover, the tempered hardness equation, considering various tempering temperatures, is precisely fitted. This investigation helps us to better understand the strengthening mechanism and performance controlling scheme of martensite stainless steel during the cast-rolling forming process in future applications.


  • Open Access

    Research on microstructure evolution and mechanical properties of steering shaft teeth after pre-heat treatment and carburizing-quenching processes

    by Yishuai Zhang, Tao Wang, Jia Fu, Hongxing Sun, Jiqiang Li, Hua Liu

    The influence of pre-heat treatment and carburizing quenching on microstructure and properties in steering gear is studied. The CCT curve and TTT curve of 20CrMnTiH are calculated by JMatPro software. According to the phase transformation theory of undercooled austenite, the pre-heat treatment process is designed and the carburizing and quenching experiments are carried out in a gas carburizing furnace. Results show that the undercooled austenite begins to transform at 814.1 °C and shows unstable at 650 °C, at which the phase transformation speed is the fastest; By controlling the cooling rate of our designed air cooling system, transformation temperature and transformation time during the undercooled austenite transformation, the metallographic structure of axle teeth after pre-heat treatment can reach grade 1, with the brinell hardness distribution is 159HB-166HB and the hardness difference less than 7HB. After carburizing and quenching the carbide grade in the gear surface can reach to grade 1. The acicular martensite and retained austenite can also reach to grade 3. In the surface of the gear the hardness is 704HV. With the request of the engineering technical standard of 0.7mm-0.9mm, the effective hardened layer depth is about 0.85 mm. This research provides a technical basis for the fatherly research on distortion characteristics.


  • Open Access

    Calculation of lattice vibrational and thermal properties of CdS nanocrystal and growth preference of CdS power during microwave-hydrothermal process

    by Jia Fu, Su Chen, Xing Liu

    The lattice vibration and thermal properties of CdS by first-principles calculations based on density functional theory are especially investigated. The results of phonon spectra show that CdS is thermodynamically stable. Combined with the concept of irreducible representation, the contribution of atoms in CdS to Raman and infrared is analyzed, that is: A1 and E1 participate in Raman vibration, and A1, E1 and E2 participate in infrared vibration. The electronic band structure and optical properties such as dielectric constant, refractive index, reflectivity are determined theoretically using DFT method. The thermal properties of CdS show that Debye temperature, isochoric specific heat capacity and coefficient of thermal expansion increase with the increase of temperature, and then tend to equilibrium. The equilibrium values are 353.13 K, 23.86 cal/cell.K and 1.04×10-4 K-1, respectively. For comparison. piezoelectric semiconductor material CdS power is synthesized by microwave hydrothermal process (temperature at 140°C + time about 15min), with particle size ranges from 50nm to 1000nm. The HRTEM imagine of CdS are experimentally studied to understand the crystal structure, with the growth preference along the plane (1000) and nanocrystal distance of 6.76 Å. This study is of great significance and provides theoretical guidance for further designing CdS matrix composite materials and to improve photoanode performance through doping of CdS and quantum dots co-sensitization.