Marcin Kujawa
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Marcin Kujawa has a total of 41 co-authors. Here are the top co-authors by number of shared publications:
Czesław Szymczak
7 shared publications- Łukasz Smakosz
Department of Structural Mechanics, Faculty of Civil and Environmental Engineering, Gdańsk University of Technology, ul. Gabriela Narutowicza 11/12, 80-233 Gdańsk, Poland
5 shared publications - Czesław Szymczak
Gdansk University of Technology
4 shared publications - Czesław Szymczak
Gdansk University of Technology
4 shared publications - Karol Winkelmann
Faculty of Civil and Environmental Engineering, Gdańsk University of Technology, Gdansk, Poland
4 shared publications - Victor A. Eremeyev
Department of Civil and Environmental Engineering and Architecture (DICAAR), University of Cagliari, Cagliari, Italy
4 shared publications
Latest Publications
- Open Access
- 4 June 2025
- Published by Elsevier in International Journal of Engineering Science
- Vol. 215
Creep failure mechanism in single-lap joints
- 4 June 2025
- Published by Elsevier in International Journal of Engineering Science
- Vol. 215
Open AccessCreep failure mechanism in single-lap joints
- Open Access
- 26 February 2025
- Published by Springer Nature in Scientific Reports
- Vol. 15 (1) , 1-17
Predicting creep failure life in adhesive-bonded single-lap joints using machine learning
Accurately predicting the creep failure life of adhesive joints, particularly single-lap adhesive joints (SLAJs), remains still a significant challenge, requiring substantial time and resources and the ability to predict the duration of creep failure in SLAJs is critical to ensuring structural integrity and reducing the failure of creep-prone adhesive joints. In this study, machine learning (ML) was used to identify the critical features that ultimately influence the durability of SLAJs due to creep. These key features were determined through correlation analysis and sequential feature selection. Multiple ML algorithms were employed to analyze complex relationships among key features and predict creep failure life. Finally, the results of the analysis highlight the importance of features such as SLAJ creep strain, adhesive tensile strength (UTS), SLAJ creep stress, adhesive surface area (A), and Young’s modulus (E). Of the ML models tested, the random forest (RF) model was the most effective in predicting creep failure life. Moreover, the accuracy of the predictions made by the proposed ML model, using original code written in Python, has been verified in experimental tests. All datasets generated and analyzed during the current study, along with the code, are available in the repository accompanying the paper.
- 26 February 2025
- Published by Springer Nature in Scientific Reports
- Vol. 15 (1) , 1-17
Open AccessPredicting creep failure life in adhesive-bonded single-lap joints using machine learning
Accurately predicting the creep failure life of adhesive joints, particularly single-lap adhesive joints (SLAJs), remains still a significant challenge, requiring substantial time and resources and the ability to predict the duration of creep failure in SLAJs is critical to ensuring structural integrity and reducing the failure of creep-prone adhesive joints. In this study, machine learning (ML) was used to identify the critical features that ultimately influence the durability of SLAJs due to creep. These key features were determined through correlation analysis and sequential feature selection. Multiple ML algorithms were employed to analyze complex relationships among key features and predict creep failure life. Finally, the results of the analysis highlight the importance of features such as SLAJ creep strain, adhesive tensile strength (UTS), SLAJ creep stress, adhesive surface area (A), and Young’s modulus (E). Of the ML models tested, the random forest (RF) model was the most effective in predicting creep failure life. Moreover, the accuracy of the predictions made by the proposed ML model, using original code written in Python, has been verified in experimental tests. All datasets generated and analyzed during the current study, along with the code, are available in the repository accompanying the paper.
- 15 February 2025
- Published by Elsevier in International Journal of Adhesion and Adhesives
- Vol. 139
Impact of thermal and humidity conditions on structural epoxy adhesives during medium-term exposure
- 15 February 2025
- Published by Elsevier in International Journal of Adhesion and Adhesives
- Vol. 139
Impact of thermal and humidity conditions on structural epoxy adhesives during medium-term exposure
- 6 January 2025
- Published by Elsevier in Structures
- Vol. 71
Mechanical performance investigations of a post-tensioned inter-module connection in steel buildings
- 6 January 2025
- Published by Elsevier in Structures
- Vol. 71
Mechanical performance investigations of a post-tensioned inter-module connection in steel buildings
- Open Access
- 12 September 2024
- Published by Polish Academy of Sciences Chancellery in Bulletin Of The Polish Academy Of Sciences-Technical Sciences
- Vol. 73 (1) , 151678
Random field-based simulational identification of potential levels of material imperfections of adhesive-bonded joints
Recently, structural adhesives have become significant in the shaping of structural elements, especially in thin-walled structures, where they replace or supplement traditional connection methods. However, adhesive-bonded joints are highly susceptible to internal structural imperfections due to their application technique and the nature of the adhesive. These material inconsistencies impact the strength parameters and the mechanical behavior of the entire connection. This study proposes a simplified method for the probabilistic numerical modeling of structural imperfections in an adhesive layer. The adhesive is modeled as an uncorrelated random field with weakened elements representing structural imperfections randomly scattered throughout its entire volume. The percentage of these imperfections (in relation to the total volume) is adopted as a random variable. By conducting experimental tests on dogbone specimens of a selected adhesive and comparing them to adequate numerical tests with varying volumes of weakened elements, the determination of the representative imperfection volume of the investigated adhesive became possible. Based on these tests, the calibration of the probability density function to describe the volume of the imperfections may be performed. Furthermore, the application of the random model for an adhesive-bonded single lap joint is shown to be viable. Finally, the calculation of a probability-based mechanical response (in this case, the normal force at critical elongation) of the single lap joint with structural imperfections is performed, and its resultant reliability is assessed and evaluated.
- 12 September 2024
- Published by Polish Academy of Sciences Chancellery in Bulletin Of The Polish Academy Of Sciences-Technical Sciences
- Vol. 73 (1) , 151678
Open AccessRandom field-based simulational identification of potential levels of material imperfections of adhesive-bonded joints
Recently, structural adhesives have become significant in the shaping of structural elements, especially in thin-walled structures, where they replace or supplement traditional connection methods. However, adhesive-bonded joints are highly susceptible to internal structural imperfections due to their application technique and the nature of the adhesive. These material inconsistencies impact the strength parameters and the mechanical behavior of the entire connection. This study proposes a simplified method for the probabilistic numerical modeling of structural imperfections in an adhesive layer. The adhesive is modeled as an uncorrelated random field with weakened elements representing structural imperfections randomly scattered throughout its entire volume. The percentage of these imperfections (in relation to the total volume) is adopted as a random variable. By conducting experimental tests on dogbone specimens of a selected adhesive and comparing them to adequate numerical tests with varying volumes of weakened elements, the determination of the representative imperfection volume of the investigated adhesive became possible. Based on these tests, the calibration of the probability density function to describe the volume of the imperfections may be performed. Furthermore, the application of the random model for an adhesive-bonded single lap joint is shown to be viable. Finally, the calculation of a probability-based mechanical response (in this case, the normal force at critical elongation) of the single lap joint with structural imperfections is performed, and its resultant reliability is assessed and evaluated.
- Open Access
- 8 August 2024
- Published by Springer Nature in Research Square
In-Plane Quasi-Static Cyclic Testing of Rc Frames Retrofitted With Rigid/Dissipating Steel Haunches
This research assessed the reliability of haunch retrofitting technique for seismic upgrade of critically damaged frames. Two 1:3 reduced scale two-story RC frames were taken under considered, which were tested previously till the near collapse state. The haunches are employed to strengthen the joint shear strength of the badly damaged joints, which are indicative of old, non-seismic, or defective joints. Damaged concrete was replaced with new high-strength concrete, and haunch-retrofitting technique was adopted to strengthen beam-column connections, in order to avoid shear hinging at joints under lateral loads. The retrofitted frames were tested through quasi-static cyclic loads in a displacement-control condition for multiple-levels of roof drifts. In order to assess the following seismic response factors: stiffness, strength, ductility, and response modification factors—lateral force-displacement capacity curves were created and examined. Hysteretic responses of tested models were analyzed to quantify hysteretic damping. The seismic performance assessment of the retrofitted frames was conducted utilizing a code-based static force approach in multiple seismic zones. The rigid haunches contributed to the over strength factor while the dissipating haunch has major contribution in energy dissipation of the retrofitted frames.
- 8 August 2024
- Published by Springer Nature in Research Square
Open AccessIn-Plane Quasi-Static Cyclic Testing of Rc Frames Retrofitted With Rigid/Dissipating Steel Haunches
This research assessed the reliability of haunch retrofitting technique for seismic upgrade of critically damaged frames. Two 1:3 reduced scale two-story RC frames were taken under considered, which were tested previously till the near collapse state. The haunches are employed to strengthen the joint shear strength of the badly damaged joints, which are indicative of old, non-seismic, or defective joints. Damaged concrete was replaced with new high-strength concrete, and haunch-retrofitting technique was adopted to strengthen beam-column connections, in order to avoid shear hinging at joints under lateral loads. The retrofitted frames were tested through quasi-static cyclic loads in a displacement-control condition for multiple-levels of roof drifts. In order to assess the following seismic response factors: stiffness, strength, ductility, and response modification factors—lateral force-displacement capacity curves were created and examined. Hysteretic responses of tested models were analyzed to quantify hysteretic damping. The seismic performance assessment of the retrofitted frames was conducted utilizing a code-based static force approach in multiple seismic zones. The rigid haunches contributed to the over strength factor while the dissipating haunch has major contribution in energy dissipation of the retrofitted frames.
- 14 February 2023
- Published by Springer Nature
- p. 449-462
The Idea of Using Adhesive Bonds in Shaping of Cold-formed Thin-walled Beam-columns
- 14 February 2023
- Published by Springer Nature
- p. 449-462
The Idea of Using Adhesive Bonds in Shaping of Cold-formed Thin-walled Beam-columns
- Open Access
- 1 January 2020
- Published by Elsevier in Engineering Failure Analysis
- Vol. 107
Finite element modelling of a historic church structure in the context of a masonry damage analysis
- 1 January 2020
- Published by Elsevier in Engineering Failure Analysis
- Vol. 107
Open AccessFinite element modelling of a historic church structure in the context of a masonry damage analysis
- 15 November 2019
- Published by Taylor & Francis in International Journal of Architectural Heritage
- Vol. 15 (10) , 1439-1456
On the Current State of Dovetail Wall-corner Joints in Wooden Greek Catholic Churches in Polish Subcarpathia with Structural and Sensitivity Analyses
This paper describes the current condition of some dovetail joints which form the wall corners of two Greek Catholic churches of wooden construction in Polish Subcarpathia. It also gives the historical background of the sacral architecture of that region. The two structures, which represent the same type of log corner joints are situated in Chotylub and Cewków. The buildings were examined e.g. for damage, wood moisture content, out-of-plane deviations and changes in the geometry of the walls. The study is based on in-situ examination and structural analysis of the joints. Finite element simulations of the statics of joints built of old, and mixture of old and new, wood are performed in order to show how the change of material properties affects their structural behaviour. Also, a sensitivity analysis is performed to describe the effect on potential repairs that combining old damp wood with new and dry joint members might have.
- 15 November 2019
- Published by Taylor & Francis in International Journal of Architectural Heritage
- Vol. 15 (10) , 1439-1456
On the Current State of Dovetail Wall-corner Joints in Wooden Greek Catholic Churches in Polish Subcarpathia with Structural and Sensitivity Analyses
This paper describes the current condition of some dovetail joints which form the wall corners of two Greek Catholic churches of wooden construction in Polish Subcarpathia. It also gives the historical background of the sacral architecture of that region. The two structures, which represent the same type of log corner joints are situated in Chotylub and Cewków. The buildings were examined e.g. for damage, wood moisture content, out-of-plane deviations and changes in the geometry of the walls. The study is based on in-situ examination and structural analysis of the joints. Finite element simulations of the statics of joints built of old, and mixture of old and new, wood are performed in order to show how the change of material properties affects their structural behaviour. Also, a sensitivity analysis is performed to describe the effect on potential repairs that combining old damp wood with new and dry joint members might have.