William R. Wampler
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
William R. Wampler has a total of 205 co-authors. Here are the top co-authors by number of shared publications:
- Dmitry L. Rudakov
University of California
9 shared publications - Tyler Abrams
General Atomics 1 , San Diego, California 92121
7 shared publications - Ezekial A. Unterberg
Oak Ridge National Laboratory (ORNL), Oak Ridge, TN (United States)
6 shared publications - Gyorgy Vizkelethy
Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States)
5 shared publications - Huiqian Wang
General Atomics 1 , P.O. Box 85608, San Diego, California 92186-5608
5 shared publications - Jerome Guterl
General Atomics, San Diego, CA 92121, United States of America
5 shared publications
Latest Publications
- Open Access
- 21 May 2026
- Published by Springer Nature in MRS Bulletin
- Vol. 51 (5) , 572-589
Point-defect kinetics in semiconductors: Experimental insights, modeling approaches, and applications
- 21 May 2026
- Published by Springer Nature in MRS Bulletin
- Vol. 51 (5) , 572-589
Open AccessPoint-defect kinetics in semiconductors: Experimental insights, modeling approaches, and applications
- 1 January 2026
- Published by IOP Publishing in Plasma Physics and Controlled Fusion
- Vol. 68 (1) , 015017
Analysis and modeling of tungsten emission and net erosion in the DIII-D divertor using updated atomic data
Tungsten (W) is one of the leading candidate materials for plasma-facing components. However, its main drawback is its high radiative efficiency; if W penetrates the plasma, it can lead to core degradation or even collapse. Since eroded tungsten tends to ionize in the sheath and redeposit promptly, the net erosion flux that escapes prompt redeposition can differ significantly from the gross erosion. This work presents a modeling framework to estimate net erosion and photon emission from W coatings exposed to the lower divertor of DIII-D using the DiMES material exposure probe. The approach couples RustBCA for sputtering yields with a Monte Carlo transport code (LPTMC) that models redeposition and W emission. Computation is carried out with new atomic data, based on R-matrix and Mons calculations, leading to lower ionization probabilities and a twofold increase in net erosion estimates compared to calculations done with OPEN-ADAS atomic data. The model results are benchmarked against experimental measurements, showing quantitative agreement for erosion, although the trends in W emission are reproduced only qualitatively. The model is also used to assess whether W II emission can serve as a direct measurement of the net erosion of W in the lower divertor of DIII-D. Simulations show that this is not valid if the electron pressure is above ∼ 120 Pa or if the toroidal length of the eroded material is smaller than the parallel-to-B distance traveled by impurity ions before steady-state conditions are reached. Finally, simulations suggest that when W is sputtered by carbon ions with high impact energies ( ≳ 300 eV) in DIII-D, W net erosion scales with W gross erosion and can be numerically approximated using W I flux alone as input.
- 1 January 2026
- Published by IOP Publishing in Plasma Physics and Controlled Fusion
- Vol. 68 (1) , 015017
Analysis and modeling of tungsten emission and net erosion in the DIII-D divertor using updated atomic data
Tungsten (W) is one of the leading candidate materials for plasma-facing components. However, its main drawback is its high radiative efficiency; if W penetrates the plasma, it can lead to core degradation or even collapse. Since eroded tungsten tends to ionize in the sheath and redeposit promptly, the net erosion flux that escapes prompt redeposition can differ significantly from the gross erosion. This work presents a modeling framework to estimate net erosion and photon emission from W coatings exposed to the lower divertor of DIII-D using the DiMES material exposure probe. The approach couples RustBCA for sputtering yields with a Monte Carlo transport code (LPTMC) that models redeposition and W emission. Computation is carried out with new atomic data, based on R-matrix and Mons calculations, leading to lower ionization probabilities and a twofold increase in net erosion estimates compared to calculations done with OPEN-ADAS atomic data. The model results are benchmarked against experimental measurements, showing quantitative agreement for erosion, although the trends in W emission are reproduced only qualitatively. The model is also used to assess whether W II emission can serve as a direct measurement of the net erosion of W in the lower divertor of DIII-D. Simulations show that this is not valid if the electron pressure is above ∼ 120 Pa or if the toroidal length of the eroded material is smaller than the parallel-to-B distance traveled by impurity ions before steady-state conditions are reached. Finally, simulations suggest that when W is sputtered by carbon ions with high impact energies ( ≳ 300 eV) in DIII-D, W net erosion scales with W gross erosion and can be numerically approximated using W I flux alone as input.
- Open Access
- 1 September 2025
- Published by Office of Scientific and Technical Information (OSTI)
Stoichiometric determination in thin films: a study of BaTiO3
- 1 September 2025
- Published by Office of Scientific and Technical Information (OSTI)
Open AccessStoichiometric determination in thin films: a study of BaTiO3
- Open Access
- 25 November 2024
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 136 (20)
Statistical analysis of displacement damage in small devices from neutron and ion irradiation
Modern semiconductor devices, such as gate-all-around nanosheet field-effect transistors (GAA NS FETs), are smaller than displacement damage cascades from fission neutrons. In this regime, device failure may occur through low-probability single events, rather than by parametric degradation previously seen in larger devices. Here, we present a statistical model that predicts the probability of a damage event in a small device and the probability distribution of the magnitude, i.e., number of displacements within the device, from each event. The model is developed first for neutron irradiation and then for energetic ion irradiation. The model is consistent with results from recent experiments in which lithium-ion irradiation produced stepwise increases in subthreshold current in GAA NS FETs.
- 25 November 2024
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 136 (20)
Open AccessStatistical analysis of displacement damage in small devices from neutron and ion irradiation
Modern semiconductor devices, such as gate-all-around nanosheet field-effect transistors (GAA NS FETs), are smaller than displacement damage cascades from fission neutrons. In this regime, device failure may occur through low-probability single events, rather than by parametric degradation previously seen in larger devices. Here, we present a statistical model that predicts the probability of a damage event in a small device and the probability distribution of the magnitude, i.e., number of displacements within the device, from each event. The model is developed first for neutron irradiation and then for energetic ion irradiation. The model is consistent with results from recent experiments in which lithium-ion irradiation produced stepwise increases in subthreshold current in GAA NS FETs.
- Open Access
- 1 October 2024
- Published by Office of Scientific and Technical Information (OSTI)
Sandia National Laboratories Boundary Physics Research at DIII-D
- 1 October 2024
- Published by Office of Scientific and Technical Information (OSTI)
Open AccessSandia National Laboratories Boundary Physics Research at DIII-D
- Open Access
- 1 December 2023
- Published by IOP Publishing in Materials Research Express
- Vol. 10 (12) , 126503
Recent DIII-D progress toward validating models of tungsten erosion, re-deposition, and migration for application to next-step fusion devices
Fundamental mechanisms governing the erosion and prompt re-deposition of tungsten impurities in tokamak divertors are identified and analyzed to inform the lifetime of tungsten plasma-facing components in ITER and other future devices. Various experiments conducted at DIII-D to benchmark predictive models are presented, leveraging the DiMES removable sample exposure probe capability and the Metal Rings Campaign, in which toroidally symmetric rows of tungsten-coated tiles were installed in the DIII-D divertor. In tokamak divertors, the width of the electric sheath is of the order of the main ion Larmor radius, and a vast majority of sputtered tungsten impurities are typically ionized within the sheath. Therefore, W prompt redeposition is mainly governed by the ratio of the characteristic ionization mean-free path of neutral tungsten to the width of the sheath. In-situ monitoring of the prompt redeposition of tungsten impurities in divertors is demonstrated via the use of WII/WI line ratios and the ionizations/photon (S/XB) method in L-mode discharges. Even with this relatively limited set of emission measurements, net erosion measurements were found to be a consistent upper bound to an analytic scaling based on the ratio of the W ionization length, λ iz , and the width of the magnetic sheath rather than the ratio of λ iz and the W+ gyro-radius. In the far-scrape-off layer (SOL) of the ITER divertor, however, it is calculated that the measurement of photon emissions associated with the ionization of tungsten impurities up to W 5 + may be required. Finally, W deposition patterns on DiMES collector probes, interpreted via DIVIMP-WallDYN modelling, reveal the key roles of progressive W erosion/re-deposition staps and E × B drifts in regulating long-range high-Z material migration.
- 1 December 2023
- Published by IOP Publishing in Materials Research Express
- Vol. 10 (12) , 126503
Open AccessRecent DIII-D progress toward validating models of tungsten erosion, re-deposition, and migration for application to next-step fusion devices
Fundamental mechanisms governing the erosion and prompt re-deposition of tungsten impurities in tokamak divertors are identified and analyzed to inform the lifetime of tungsten plasma-facing components in ITER and other future devices. Various experiments conducted at DIII-D to benchmark predictive models are presented, leveraging the DiMES removable sample exposure probe capability and the Metal Rings Campaign, in which toroidally symmetric rows of tungsten-coated tiles were installed in the DIII-D divertor. In tokamak divertors, the width of the electric sheath is of the order of the main ion Larmor radius, and a vast majority of sputtered tungsten impurities are typically ionized within the sheath. Therefore, W prompt redeposition is mainly governed by the ratio of the characteristic ionization mean-free path of neutral tungsten to the width of the sheath. In-situ monitoring of the prompt redeposition of tungsten impurities in divertors is demonstrated via the use of WII/WI line ratios and the ionizations/photon (S/XB) method in L-mode discharges. Even with this relatively limited set of emission measurements, net erosion measurements were found to be a consistent upper bound to an analytic scaling based on the ratio of the W ionization length, λ iz , and the width of the magnetic sheath rather than the ratio of λ iz and the W+ gyro-radius. In the far-scrape-off layer (SOL) of the ITER divertor, however, it is calculated that the measurement of photon emissions associated with the ionization of tungsten impurities up to W 5 + may be required. Finally, W deposition patterns on DiMES collector probes, interpreted via DIVIMP-WallDYN modelling, reveal the key roles of progressive W erosion/re-deposition staps and E × B drifts in regulating long-range high-Z material migration.
- Open Access
- 24 August 2023
- Published by IOP Publishing in Nuclear Fusion
- Vol. 63 (10) , 106004
In-situ coating of silicon-rich films on tokamak plasma-facing components with real-time Si material injection
Experiments have been conducted in the DIII-D tokamak to explore the in-situ growth of silicon-rich layers as a potential technique for real-time replenishment of surface coatings on plasma-facing components (PFCs) during steady-state long-pulse reactor operation. Silicon (Si) pellets of 1 mm diameter were injected into low- and high-confinement (L-mode and H-mode) plasma discharges with densities ranging from 3.9– 7.5 × 10 19 m−3 and input powers ranging from 5.5 to 9 MW. The small Si pellets were delivered with the impurity granule injector at frequencies ranging from 4 to 16 Hz corresponding to mass flow rates of 5–19 mg s−1 (1– 4.2 × 10 20 Si s−1) at cumulative amounts of up to 34 mg of Si per five-second discharge. Graphite samples were exposed to the scrape-off layer and private flux region plasmas through the divertor material evaluation system to evaluate the Si deposition on the divertor targets. The Si II emission at the sample correlates with silicon injection and suggests net surface Si-deposition in measurable amounts. Post-mortem analysis showed Si-rich coatings containing silicon oxides, of which SiO2 is the dominant component. No evidence of SiC was found, which is attributed to low divertor surface temperatures. The in-situ and ex-situ analysis found that Si-rich coatings of at least 0.4–1.2 nm thickness have been deposited at 0.4–0.7 nm s−1. The technique is estimated to coat a surface area of at least 0.94 m2 on the outer divertor. These results demonstrate the potential of using real-time material injection to form Si-enriched layers on divertor PFCs during reactor operation.
- 24 August 2023
- Published by IOP Publishing in Nuclear Fusion
- Vol. 63 (10) , 106004
Open AccessIn-situ coating of silicon-rich films on tokamak plasma-facing components with real-time Si material injection
Experiments have been conducted in the DIII-D tokamak to explore the in-situ growth of silicon-rich layers as a potential technique for real-time replenishment of surface coatings on plasma-facing components (PFCs) during steady-state long-pulse reactor operation. Silicon (Si) pellets of 1 mm diameter were injected into low- and high-confinement (L-mode and H-mode) plasma discharges with densities ranging from 3.9– 7.5 × 10 19 m−3 and input powers ranging from 5.5 to 9 MW. The small Si pellets were delivered with the impurity granule injector at frequencies ranging from 4 to 16 Hz corresponding to mass flow rates of 5–19 mg s−1 (1– 4.2 × 10 20 Si s−1) at cumulative amounts of up to 34 mg of Si per five-second discharge. Graphite samples were exposed to the scrape-off layer and private flux region plasmas through the divertor material evaluation system to evaluate the Si deposition on the divertor targets. The Si II emission at the sample correlates with silicon injection and suggests net surface Si-deposition in measurable amounts. Post-mortem analysis showed Si-rich coatings containing silicon oxides, of which SiO2 is the dominant component. No evidence of SiC was found, which is attributed to low divertor surface temperatures. The in-situ and ex-situ analysis found that Si-rich coatings of at least 0.4–1.2 nm thickness have been deposited at 0.4–0.7 nm s−1. The technique is estimated to coat a surface area of at least 0.94 m2 on the outer divertor. These results demonstrate the potential of using real-time material injection to form Si-enriched layers on divertor PFCs during reactor operation.
- 16 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 70 (4) , 469-477
Transient Photocurrent From High-Voltage Vertical GaN Diodes Irradiated With Electrons: Experiments and Simulations
Radiation-hard high-voltage vertical GaN p-n diodes are being developed for use in power electronics subjected to ionizing radiation. We present a comparison of the measured and simulated photocurrent response of diodes exposed to ionizing irradiation with 70 keV and 20 MeV electrons at dose rates in the range of 1.4x10 7 - 5.0x10 8 rad(GaN)/s. The simulations correctly predict the trend in measured steady-state photocurrent and agree with experimental results within a factor of 2. Furthermore, simulations of the transient photocurrent response to dose rates with uniform and non-uniform ionization depth profiles uncover the physical processes involved that cannot be otherwise experimentally observed due to orders of magnitude larger RC time constant of the test circuit. The simulations were performed using an Exploratory Physics Development code developed at Sandia National Laboratories. The code offers the capability to include defect physics under more general conditions, not included in commercially available software packages, extending the applicability of the simulations to different types of radiation environments.
- 16 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 70 (4) , 469-477
Transient Photocurrent From High-Voltage Vertical GaN Diodes Irradiated With Electrons: Experiments and Simulations
Radiation-hard high-voltage vertical GaN p-n diodes are being developed for use in power electronics subjected to ionizing radiation. We present a comparison of the measured and simulated photocurrent response of diodes exposed to ionizing irradiation with 70 keV and 20 MeV electrons at dose rates in the range of 1.4x10 7 - 5.0x10 8 rad(GaN)/s. The simulations correctly predict the trend in measured steady-state photocurrent and agree with experimental results within a factor of 2. Furthermore, simulations of the transient photocurrent response to dose rates with uniform and non-uniform ionization depth profiles uncover the physical processes involved that cannot be otherwise experimentally observed due to orders of magnitude larger RC time constant of the test circuit. The simulations were performed using an Exploratory Physics Development code developed at Sandia National Laboratories. The code offers the capability to include defect physics under more general conditions, not included in commercially available software packages, extending the applicability of the simulations to different types of radiation environments.
- Open Access
- 6 December 2022
- Published by IOP Publishing in Nuclear Fusion
- Vol. 63 (1) , 016012
Misalignment of magnetic field in DIII-D assessed by post-mortem analysis of divertor targets
We assess the toroidal magnetic field B t asymmetry in DIII-D due to a misalignment of the toroidal field coils with respect to the poloidal magnetic field coils and vacuum vessel. The peak-to-peak variation of the divertor strike point (SP) radius is measured to be 1 cm, with an n = 1 toroidal pattern. We use the centre of a narrow carbon deposition band on tungsten-coated divertor tiles just inside the outer strike point (OSP) as a proxy for the divertor SP location. The band occurred in a series of reverse B t discharges with the OSP positioned on the divertor inserts due to strong E × B drift transport of C from the inner to the outer SP through the private flux region. The variation in band radius (and hence the magnetic SP) is a (4.89 ± 0.31) mm shift toward (310 ± 4)° toroidal direction. These measurements agree well with previous measurements of the 3D magnetic field distribution (Luxon 2003 Nucl. Fusion 43 1813), simulations performed by the mafot field line integration code, and recent Langmuir probe measurements in the small-angle-slot (SAS) divertor (Watkins et al 2019 Nucl. Mater. Energy 18 46). Comparison of these measurements in the SAS divertor also indicates that there is the possibility of a tilt (in conjunction with the shift) of the B t coil field of (0.04 ± 0.07)° towards the toroidal angle of (215 ± 25)°. Previous measurements suggested a field misalignment of (4.6 ± 0.3) mm in the 270° toroidal direction, and a tilt of (0.06 ± 0.02)° toward the 114° toroidal direction, which is similar to the results reported here. These studies will be important for better understanding the radial variation of the toroidal strike line in DIII-D, for designing the new generation of SAS divertor, and for developing an understanding of the impact of error fields on tokamaks with tightly baffled slot divertors.
- 6 December 2022
- Published by IOP Publishing in Nuclear Fusion
- Vol. 63 (1) , 016012
Open AccessMisalignment of magnetic field in DIII-D assessed by post-mortem analysis of divertor targets
We assess the toroidal magnetic field B t asymmetry in DIII-D due to a misalignment of the toroidal field coils with respect to the poloidal magnetic field coils and vacuum vessel. The peak-to-peak variation of the divertor strike point (SP) radius is measured to be 1 cm, with an n = 1 toroidal pattern. We use the centre of a narrow carbon deposition band on tungsten-coated divertor tiles just inside the outer strike point (OSP) as a proxy for the divertor SP location. The band occurred in a series of reverse B t discharges with the OSP positioned on the divertor inserts due to strong E × B drift transport of C from the inner to the outer SP through the private flux region. The variation in band radius (and hence the magnetic SP) is a (4.89 ± 0.31) mm shift toward (310 ± 4)° toroidal direction. These measurements agree well with previous measurements of the 3D magnetic field distribution (Luxon 2003 Nucl. Fusion 43 1813), simulations performed by the mafot field line integration code, and recent Langmuir probe measurements in the small-angle-slot (SAS) divertor (Watkins et al 2019 Nucl. Mater. Energy 18 46). Comparison of these measurements in the SAS divertor also indicates that there is the possibility of a tilt (in conjunction with the shift) of the B t coil field of (0.04 ± 0.07)° towards the toroidal angle of (215 ± 25)°. Previous measurements suggested a field misalignment of (4.6 ± 0.3) mm in the 270° toroidal direction, and a tilt of (0.06 ± 0.02)° toward the 114° toroidal direction, which is similar to the results reported here. These studies will be important for better understanding the radial variation of the toroidal strike line in DIII-D, for designing the new generation of SAS divertor, and for developing an understanding of the impact of error fields on tokamaks with tightly baffled slot divertors.
- Open Access
- 1 September 2022
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 132 (9) , 095702
Carrier capture and emission by substitutional carbon impurities in GaN vertical diodes
A model was developed for the operation of a GaN pn junction vertical diode which includes rate equations for carrier capture and thermally activated emission by substitutional carbon impurities and carrier generation by ionizing radiation. The model was used to simulate the effect of ionizing radiation on the charge state of carbon. These simulations predict that with no applied bias, carbon is negatively charged in the n-doped layer, thereby compensating n-doping as experimentally observed in diodes grown by metal-organic chemical vapor deposition. With reverse bias, carbon remains negative in the depletion region, i.e., compensation persists in the absence of ionization but is neutralized by exposure to ionizing radiation. This increases charge density in the depletion region, decreases the depletion width, and increases the capacitance. The predicted increase in capacitance was experimentally observed using a pulsed 70 keV electron beam as the source of ionization. In additional confirming experiments, the carbon charge-state conversion was accomplished by photoionization using sub-bandgap light or by the capture of holes under forward bias.
- 1 September 2022
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 132 (9) , 095702
Open AccessCarrier capture and emission by substitutional carbon impurities in GaN vertical diodes
A model was developed for the operation of a GaN pn junction vertical diode which includes rate equations for carrier capture and thermally activated emission by substitutional carbon impurities and carrier generation by ionizing radiation. The model was used to simulate the effect of ionizing radiation on the charge state of carbon. These simulations predict that with no applied bias, carbon is negatively charged in the n-doped layer, thereby compensating n-doping as experimentally observed in diodes grown by metal-organic chemical vapor deposition. With reverse bias, carbon remains negative in the depletion region, i.e., compensation persists in the absence of ionization but is neutralized by exposure to ionizing radiation. This increases charge density in the depletion region, decreases the depletion width, and increases the capacitance. The predicted increase in capacitance was experimentally observed using a pulsed 70 keV electron beam as the source of ionization. In additional confirming experiments, the carbon charge-state conversion was accomplished by photoionization using sub-bandgap light or by the capture of holes under forward bias.