Shiwei Zhang

To solve the multi-objective and multi-scheme problems in the construction resource allocation plan, the organization and procurement of materials and mechanical equipment are considered. The optimal solution of construction resource allocation decision is obtained by rational allocation of labor and other subjective factors, and other additional costs horizontal data comparison. In this paper, the data in resource allocation are quantified and compared. The coupling weighted model is proposed based on the traditional weighted grey target model. The quantitative results of each module are obtained by using the two methods of Analytic Hierarchy Process (AHP) and Criteria Importance Error Intercrieria Correlation (CRITIC). The improved method of scoring all modules and making a comprehensive evaluation is used. Finally, the Lagrange multiplier method is used for coupling. On this basis, based on the coupled weighting model, the feasibility and application rationality of the optimization method are proved with examples. This method provides theoretical reference and practical support for the final choice of resource allocation.

A 2D axi-symmetric theoretical model of dielectric porous media in intermittent microwave (IMW) thermal process was developed, and the electromagnetic energy, multiphase transport, phase change, large deformation, and glass transition were taken into consideration. From the simulation results, the mass was mainly carried by the liquid water, and the heat was mainly carried by liquid water and solid. The diffusion was the dominant mechanism of the mass transport during the whole process, whereas for the heat transport, the convection dominated the heat transport near the surface areas during the heating stage. The von Mises stress reached local maxima at different locations at different stages, and all were lower than the fracture stress. A material treated by a longer intermittent cycle length with the same pulse ratio (PR) tended to trigger the phenomena of overheat and fracture due to the more intense fluctuation of moisture content, temperature, deformation, and von Mises stress. The model can be extended to simulate the intermittent radio frequency (IRF) process on the basis of which one can select a suitable energy source for a specific process.

Knudsen force generated by thermally driven gas flow in a microscale structure has been used for gas detection and has shown immeasurable potential in the field of microelectromechanical system (MEMS) gas sensors due to its novel sensing characteristics. In this article, the performances of three kinds of Knudsen force gas sensors with improved isosceles triangular shuttle arm structures were studied. In the first design, the top side and right side lengths were equal; in the second, the top side and bottom side lengths were equal; and for the third, the bottom side and right side lengths were equal. A detailed investigation including gas flow, thermal characteristics, Knudsen force, and coupling effects between the shuttle-heater pairs was conducted using the direct simulation Monte Carlo (DSMC) method and the main mechanisms for gas flow presented were almost the same in this work. However, the second design returned the highest Knudsen force performance. The value increased by 42.9% (P = 387 Pa) compared to the Knudsen force of the original square shuttle arm. The results also demonstrate that the coupling effects become weak toward the right with an increase in the number of shuttle-heater pairs.

A Knudsen pump operates under the thermal transpiration effect or the thermal edge effect on the micro-scale. Due to the uneven temperature distribution of the walls in the channel axis direction or the constant temperature of the tips on the walls, directional thermally-induced flow is generated. In this paper the Direct Simulation Monte Carlo (DSMC) method is applied for N₂–O₂ gas mixtures in the ratios of 4:1, 1:1, and 1:4 with different Knudsen numbers in a classic rectangular Knudsen pump to study the flow characteristics of the gas mixtures in the pump. The results show that the changing in the gas physical properties does not affect the distribution of the velocity field, temperature fields, or other fields in the Knudsen pump. The thermal creep effect is related to the molecular mass of the gas. Even in N₂ and O₂ gas mixtures with similar molecular masses, N₂ can be also found to have a stronger thermal creep effect. Moreover, the lighter molecular weight gas (N₂) can effectively promote the motion of the heavier gas (O₂).

Aiming at improving the food quality during microwave process, this article mainly focused on the numerical simulation of shape effect, which was evaluated by microwave power absorption capability and temperature distribution uniformity in a single sample heated in a domestic microwave oven. This article only took the electromagnetic field and heat conduction in solid into consideration. The Maxwell equations were used to calculate the distribution of microwave electromagnetic field distribution in the microwave cavity and samples; then the electromagnetic energy was coupled as the heat source in the heat conduction process in samples. Quantitatively, the power absorption capability and temperature distribution uniformity were, respectively, described by power absorption efficiency (PAE) and the statistical variation of coefficient (COV). In addition, we defined the comprehensive evaluation coefficient (CEC) to describe the usability of a specific sample. In accordance with volume or the wave numbers and penetration numbers in the radial and axial directions of samples, they can be classified into different groups. And according to the PAE, COV, and CEC value and the specific need of microwave process, an optimal sample shape and orientation could be decided.

In this article, we have proposed and demonstrated two new approaches to implement microwave photonic filter with tunable multi-passband based on reflective fiber Mach-Zehnder interferometer and cascaded fiber Mach-Zehnder interferometers and dispersive medium. The proposed MPF has simple structure and is easy to implement, also the experimental results show good tunability and switch performances.

The working principle of the refractive-type fiber optic liquid level sensor is analyzed in detail based on the light refraction principle. The optic path models are developed in consideration of common simplification and the residual liquid film on the glass tube wall. The calculating formulae for the model are derived, constraint conditions are obtained, influencing factors are discussed, and the scopes and skills of application are analyzed through instance simulations. The research results are useful in directing the correct usage of the fiber optic liquid level sensor, especially in special cases, such as those involving viscous liquid in the glass tube monitoring.

The solvent vapor phase drying process is one of the most important processes during the production and maintenance for large oil‐immersed power transformer. In this paper, the working principle, system composition, and technological process of mobile solvent vapor phase drying (MVPD) equipment for transformer are introduced in detail. On the basis of necessary simplification and assumption for MVPD equipment and process, a heat and mass transfer mathematical model including 40 mathematical equations is established, which represents completely thermodynamics laws of phase change and transport process of solvent, water, and air in MVPD technological processes and describes in detail the quantitative relationship among important physical quantities such as temperature, pressure, and flux in key equipment units and process. Taking a practical field drying process of 500 KV/750 MVA power transformer as an example, the simulation calculation of a complete technological process is carried out by programming with MATLAB software and some relation curves of key process parameters changing with time are obtained such as body temperature, tank pressure, and water yield. The change trend of theoretical simulation results is very consistent with the actual production record data which verifies the correctness of mathematical model established.

To determine the mechanism of energy consumption in hot air drying, we simulate the interior heat and mass transfer processes that occur during the hot air drying for a single corn grain. The simulations are based on a 3D solid model. The 3D real body model is obtained by scanning the corn kernels with a high-precision medical CT machine. The CT images are then edited by MIMICS and ANSYS software to reconstruct the three-dimensional real body model of a corn kernel. The Fourier heat conduction equation, the Fick diffusion equation, the heat transfer coefficient, and the mass diffusion coefficient are chosen as the governing equations of the theoretical dry model. The calculation software, COMSOL Multiphysics, is used to complete the simulation calculation. The influence of air temperature and velocity on the heat and mass transfer processes is discussed. Results show that mass transfer dominates during the hot air drying of corn grains. Air temperature and velocity are chosen primarily in consideration of mass transfer effects. A low velocity leads to less energy consumption.