Rabindra Pahari
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Rabindra Pahari has a total of 77 co-authors. Here are the top co-authors by number of shared publications:
Ralph Skomski
Department of Physics and Astronomy, University of Nebraska 1 , Lincoln, Nebraska 68588, USA
8 shared publications- Balamurugan Balasubramanian
Nebraska Center for Materials and Nanoscience and Department of Physics and Astronomy, University of Nebraska, Lincoln, Nebraska 68588, USA
6 shared publications Shah R. Valloppilly
Nebraska Center for Materials and Nanoscience, University of Nebraska, Lincoln, Nebraska 68588, USA
5 shared publications- Ahsan Ullah
Department of Physics and Astronomy and Nebraska Center for Materials and Nanoscience, University of Nebraska, Lincoln, Nebraska 68588, USA
4 shared publications - David J. Sellmyer
Nebraska Center for Materials and Nanoscience, University of Nebraska, Lincoln, Nebraska 68588, USA
4 shared publications - Lanping Yue
Nebraska Center for Materials and Nanoscience, University of Nebraska 1 , Lincoln, Nebraska 68588, USA
4 shared publications
Latest Publications
- 29 July 2022
- Published by American Physical Society (APS) in Physical Review Materials
- Vol. 6 (7) , 074206
Room temperature spin-orbit torque efficiency in sputtered low-temperature superconductor δ -TaN
In the course of searching for promising topological materials for applications in future topological electronics, we evaluated spin-orbit torques (SOTs) in high-quality sputtered δ-TaN/ devices through spin-torque ferromagnetic resonance (ST-FMR) and spin pumping measurements. From the ST-FMR characterization we observed a significant linewidth modulation in the magnetic layer attributed to the charge-to-spin conversion generated from the δ-TaN layer. Remarkably, the spin-torque efficiency determined from ST-FMR and spin pumping measurements is as large as 0.034 and 0.031, respectively. These values are over two times larger than for α-Ta, but almost five times lower than for β-Ta, which can be attributed to the low room temperature electrical resistivity in δ-TaN. A large spin diffusion length of at least is estimated, which is comparable to the spin diffusion length in pure Ta. Comprehensive experimental analysis, together with density functional theory calculations, indicates that the origin of the pronounced SOT effect in δ-TaN can be mostly related to a significant contribution from the Berry curvature associated with the presence of a topically nontrivial electronic band structure in the vicinity of the Fermi level (). Through additional detailed theoretical analysis, we also found that an isostructural allotrope of the superconducting δ-TaN phase, the simple hexagonal structure θ-TaN, has larger Berry curvature, and that, together with expected reasonable charge conductivity, it can also be a promising candidate for exploring a generation of spin-orbit torque magnetic random access memory as cheap, temperature stable, and highly efficient spin current source.- 29 July 2022
- Published by American Physical Society (APS) in Physical Review Materials
- Vol. 6 (7) , 074206
Room temperature spin-orbit torque efficiency in sputtered low-temperature superconductor δ -TaN
In the course of searching for promising topological materials for applications in future topological electronics, we evaluated spin-orbit torques (SOTs) in high-quality sputtered δ-TaN/ devices through spin-torque ferromagnetic resonance (ST-FMR) and spin pumping measurements. From the ST-FMR characterization we observed a significant linewidth modulation in the magnetic layer attributed to the charge-to-spin conversion generated from the δ-TaN layer. Remarkably, the spin-torque efficiency determined from ST-FMR and spin pumping measurements is as large as 0.034 and 0.031, respectively. These values are over two times larger than for α-Ta, but almost five times lower than for β-Ta, which can be attributed to the low room temperature electrical resistivity in δ-TaN. A large spin diffusion length of at least is estimated, which is comparable to the spin diffusion length in pure Ta. Comprehensive experimental analysis, together with density functional theory calculations, indicates that the origin of the pronounced SOT effect in δ-TaN can be mostly related to a significant contribution from the Berry curvature associated with the presence of a topically nontrivial electronic band structure in the vicinity of the Fermi level (). Through additional detailed theoretical analysis, we also found that an isostructural allotrope of the superconducting δ-TaN phase, the simple hexagonal structure θ-TaN, has larger Berry curvature, and that, together with expected reasonable charge conductivity, it can also be a promising candidate for exploring a generation of spin-orbit torque magnetic random access memory as cheap, temperature stable, and highly efficient spin current source.- Open Access
- 11 May 2022
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 131 (18)
Magnetic moments and spin structure in single-phase B20 Co1+xSi1−x (x = 0.043)
Neutron powder diffraction (NPD) and x-ray magnetic circular dichroism (XMCD) spectroscopy are employed to investigate the magnetism and spin structure in single-phase B20 Co1.043Si0.957. The magnetic contributions to the NPD data measured in zero fields are consistent with the helical order among the allowed spin structures derived from group theory. The magnitude of the magnetic moment is (0.3 ± 0.1)μB/Co according to NPD, while the surface magnetization probed by XMCD at 3 kOe is (0.18–0.31)μB/Co. Both values are substantially larger than the bulk magnetization of 0.11μB/Co determined from magnetometry at 70 kOe and 2 K. These experimental data indicate the formation of a helical spin phase and the associated conical states in high magnetic fields.
- 11 May 2022
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 131 (18)
Open AccessMagnetic moments and spin structure in single-phase B20 Co1+xSi1−x (x = 0.043)
Neutron powder diffraction (NPD) and x-ray magnetic circular dichroism (XMCD) spectroscopy are employed to investigate the magnetism and spin structure in single-phase B20 Co1.043Si0.957. The magnetic contributions to the NPD data measured in zero fields are consistent with the helical order among the allowed spin structures derived from group theory. The magnitude of the magnetic moment is (0.3 ± 0.1)μB/Co according to NPD, while the surface magnetization probed by XMCD at 3 kOe is (0.18–0.31)μB/Co. Both values are substantially larger than the bulk magnetization of 0.11μB/Co determined from magnetometry at 70 kOe and 2 K. These experimental data indicate the formation of a helical spin phase and the associated conical states in high magnetic fields.
- 29 December 2021
- Published by American Physical Society (APS) in Physical Review Materials
- Vol. 5 (12) , 124418
Peripheral chiral spin textures and topological Hall effect in CoSi nanomagnets
The spin structure and transport behavior of B20-ordered CoSi nanomagnets are investigated experimentally and by theoretical calculations. B20 materials are of interest in spin electronics because their noncentrosymmetric crystal structure favors noncoplanar spin structures that yield a contribution to the Hall effect. However, stoichiometric bulk CoSi is nonmagnetic, and combining magnetic order at and above room temperature with small feature sizes has remained a general challenge. Our CoSi nanoclusters have an average size of 11.6 nm and a magnetic ordering temperature of 330 K. First-principle calculations and x-ray circular dichroism experiments show that the magnetic moment is predominantly confined to the shells of the clusters. The CoSi nanocluster ensemble exhibits a topological Hall effect, which is explained by an analytical model and by micromagnetic simulations on the basis of competing Dzyaloshinskii-Moriya and intra- and intercluster exchange interactions. The topological Hall effect is caused by formation of chiral spin textures in the shells of the clusters, which exhibit fractional skyrmion number and are therefore termed as paraskyrmions (closely related to skyrmion spin structures). This research shows how nanostructuring of a chiral atomic structure can create a spin-textured material with a topological Hall effect and a magnetic ordering temperature above room temperature.
- 29 December 2021
- Published by American Physical Society (APS) in Physical Review Materials
- Vol. 5 (12) , 124418
Peripheral chiral spin textures and topological Hall effect in CoSi nanomagnets
The spin structure and transport behavior of B20-ordered CoSi nanomagnets are investigated experimentally and by theoretical calculations. B20 materials are of interest in spin electronics because their noncentrosymmetric crystal structure favors noncoplanar spin structures that yield a contribution to the Hall effect. However, stoichiometric bulk CoSi is nonmagnetic, and combining magnetic order at and above room temperature with small feature sizes has remained a general challenge. Our CoSi nanoclusters have an average size of 11.6 nm and a magnetic ordering temperature of 330 K. First-principle calculations and x-ray circular dichroism experiments show that the magnetic moment is predominantly confined to the shells of the clusters. The CoSi nanocluster ensemble exhibits a topological Hall effect, which is explained by an analytical model and by micromagnetic simulations on the basis of competing Dzyaloshinskii-Moriya and intra- and intercluster exchange interactions. The topological Hall effect is caused by formation of chiral spin textures in the shells of the clusters, which exhibit fractional skyrmion number and are therefore termed as paraskyrmions (closely related to skyrmion spin structures). This research shows how nanostructuring of a chiral atomic structure can create a spin-textured material with a topological Hall effect and a magnetic ordering temperature above room temperature.
- 1 November 2021
- Published by Elsevier in Journal of Magnetism and Magnetic Materials
- Vol. 537
Magnetism and topological Hall effect in antiferromagnetic Ru2MnSn-based Heusler compounds
- 1 November 2021
- Published by Elsevier in Journal of Magnetism and Magnetic Materials
- Vol. 537
Magnetism and topological Hall effect in antiferromagnetic Ru2MnSn-based Heusler compounds
- 5 February 2021
- Published by American Physical Society (APS) in Physical Review Materials
- Vol. 5 (2) , 024402
Magnetic and electron transport properties of nanomagnetsMagnetotransport and ferromagnetism in thin films of nanoclusters are investigated experimentally and theoretically. The nanoclusters are fabricated by an inert-gas condensation-type cluster-deposition method and have an average size of 11.3 nm. Unlike the bulk that exhibits a very weak net magnetic moment only below 10 K, the nanoclusters exhibit room-temperature ferromagnetism with a substantial saturation magnetization. Key features of the system are its closeness to the Stoner transition, magnetic moments induced by spin polarization starting from surface atoms, and nonuniaxial anisotropy associated with the orthorhombic crystal structure of . A method is introduced to determine the effective anisotropy using the experimental magnetization data of this complex system and its relationship with the two lowest-order nonuniaxial anisotropy constants. On decreasing temperature from 300 K, the nanoclusters show electron-transport properties unusual for a ferromagnetic metal, including an increase of Hall resistivity and a nonmonotonic change of negative magnetoresistance with a peak at around 100 K. The underlying physics is explained on the basis of the large polarization of surface spins and variation in the degree of their misalignments due to temperature-dependent effective anisotropy.- 5 February 2021
- Published by American Physical Society (APS) in Physical Review Materials
- Vol. 5 (2) , 024402
Magnetic and electron transport properties of nanomagnetsMagnetotransport and ferromagnetism in thin films of nanoclusters are investigated experimentally and theoretically. The nanoclusters are fabricated by an inert-gas condensation-type cluster-deposition method and have an average size of 11.3 nm. Unlike the bulk that exhibits a very weak net magnetic moment only below 10 K, the nanoclusters exhibit room-temperature ferromagnetism with a substantial saturation magnetization. Key features of the system are its closeness to the Stoner transition, magnetic moments induced by spin polarization starting from surface atoms, and nonuniaxial anisotropy associated with the orthorhombic crystal structure of . A method is introduced to determine the effective anisotropy using the experimental magnetization data of this complex system and its relationship with the two lowest-order nonuniaxial anisotropy constants. On decreasing temperature from 300 K, the nanoclusters show electron-transport properties unusual for a ferromagnetic metal, including an increase of Hall resistivity and a nonmonotonic change of negative magnetoresistance with a peak at around 100 K. The underlying physics is explained on the basis of the large polarization of surface spins and variation in the degree of their misalignments due to temperature-dependent effective anisotropy.- 6 February 2020
- Published by American Physical Society (APS) in Physical Review Letters
- Vol. 124 (5) , 057201
Chiral Magnetism and High-Temperature Skyrmions in B20-Ordered Co-Si
Magnets with chiral crystal structures and helical spin structures have recently attracted much attention as potential spin-electronics materials, but their relatively low magnetic-ordering temperatures are a disadvantage. While cobalt has long been recognized as an element that promotes high-temperature magnetic ordering, most Co-rich alloys are achiral and exhibit collinear rather than helimagnetic order. Crystallographically, the B20-ordered compound CoSi is an exception due to its chiral structure, but it does not exhibit any kind of magnetic order. Here, we use nonequilibrium processing to produce B20-ordered with a maximum Co solubility of . Above a critical excess-Co content (), the alloys are magnetically ordered, and for , a critical temperature is obtained, the highest among all B20-type magnets. The crystal structure of the alloy supports spin spirals caused by Dzyaloshinskii-Moriya interactions, and from magnetic measurements we estimate that the spirals have a periodicity of about 17 nm. Our density-functional calculations explain the combination of high magnetic-ordering temperature and short periodicity in terms of a quantum phase transition where excess-cobalt spins are coupled through the host matrix.- 6 February 2020
- Published by American Physical Society (APS) in Physical Review Letters
- Vol. 124 (5) , 057201
Chiral Magnetism and High-Temperature Skyrmions in B20-Ordered Co-Si
Magnets with chiral crystal structures and helical spin structures have recently attracted much attention as potential spin-electronics materials, but their relatively low magnetic-ordering temperatures are a disadvantage. While cobalt has long been recognized as an element that promotes high-temperature magnetic ordering, most Co-rich alloys are achiral and exhibit collinear rather than helimagnetic order. Crystallographically, the B20-ordered compound CoSi is an exception due to its chiral structure, but it does not exhibit any kind of magnetic order. Here, we use nonequilibrium processing to produce B20-ordered with a maximum Co solubility of . Above a critical excess-Co content (), the alloys are magnetically ordered, and for , a critical temperature is obtained, the highest among all B20-type magnets. The crystal structure of the alloy supports spin spirals caused by Dzyaloshinskii-Moriya interactions, and from magnetic measurements we estimate that the spirals have a periodicity of about 17 nm. Our density-functional calculations explain the combination of high magnetic-ordering temperature and short periodicity in terms of a quantum phase transition where excess-cobalt spins are coupled through the host matrix.- Open Access
- 1 December 2019
- Published by AIP Publishing in APL Materials
- Vol. 7 (12) , 121111
High energy product of MnBi by field annealing and Sn alloying
Permanent-magnet materials are one cornerstone of today’s technology, abundant in disk drives, motors, medical equipment, wind generators, and cars. A continuing challenge has been to reconcile high permanent-magnet performance with low raw-material costs. This work reports a Mn-Bi-Sn alloy exclusively made from inexpensive elements, exhibiting high values of Curie-temperature, magnetization, anisotropy, coercivity, and energy product. The samples are produced by field annealing of rapidly quenched Sn-containing MnBi alloys, where the improvement of the magnetic properties is caused by the substitutional occupancy of the 2c sites in the hexagonal NiAs structure by Sn. The substitution modifies the electronic structure of the compound and enhances the magnetocrystalline anisotropy, thereby improving the coercivity of the compound. The energy product reaches 114 kJ/m3 (14.3 MGOe) at room temperature and 86 kJ/m3 (10.8 MGOe) at 200 °C; this value is similar to that of the Dy-free Nd2Fe14B and exceeds that of other rare-earth-free permanent-magnet bulk alloys, as encountered in automotive applications.
- 1 December 2019
- Published by AIP Publishing in APL Materials
- Vol. 7 (12) , 121111
Open AccessHigh energy product of MnBi by field annealing and Sn alloying
Permanent-magnet materials are one cornerstone of today’s technology, abundant in disk drives, motors, medical equipment, wind generators, and cars. A continuing challenge has been to reconcile high permanent-magnet performance with low raw-material costs. This work reports a Mn-Bi-Sn alloy exclusively made from inexpensive elements, exhibiting high values of Curie-temperature, magnetization, anisotropy, coercivity, and energy product. The samples are produced by field annealing of rapidly quenched Sn-containing MnBi alloys, where the improvement of the magnetic properties is caused by the substitutional occupancy of the 2c sites in the hexagonal NiAs structure by Sn. The substitution modifies the electronic structure of the compound and enhances the magnetocrystalline anisotropy, thereby improving the coercivity of the compound. The energy product reaches 114 kJ/m3 (14.3 MGOe) at room temperature and 86 kJ/m3 (10.8 MGOe) at 200 °C; this value is similar to that of the Dy-free Nd2Fe14B and exceeds that of other rare-earth-free permanent-magnet bulk alloys, as encountered in automotive applications.
- 21 October 2019
- Published by AIP Publishing in Applied Physics Letters
- Vol. 115 (17) , 172404
Comparative study of topological Hall effect and skyrmions in NiMnIn and NiMnGa
A nonequilibrium rapid-quenching method has been used to fabricate NiMnIn and NiMnGa alloys that are chemically and morphologically similar but crystallographically and physically very different. NiMnGa crystallizes in a Ni2In-type hexagonal structure, whereas NiMnIn is a cubic Heusler alloy. Both alloys yield a topological Hall effect contribution corresponding to bubble-type skyrmion spin structures, but it occurs in much lower magnetic fields in NiMnIn as compared to NiMnGa. The effect is unrelated to net Dzyaloshinskii-Moriya interactions, which are absent in both alloys due to their inversion-symmetric crystal structures. Based on magnetic-force microscopy, we explain the difference between the two alloys by magnetocrystalline anisotropy and uniaxial and cubic anisotropies yielding full-fledged and reduced topological Hall effects, respectively. Since NiMnIn involves small magnetic fields (0.02–0.3 kOe) at and above room temperature, it is of potential interest in spin electronics.
- 21 October 2019
- Published by AIP Publishing in Applied Physics Letters
- Vol. 115 (17) , 172404
Comparative study of topological Hall effect and skyrmions in NiMnIn and NiMnGa
A nonequilibrium rapid-quenching method has been used to fabricate NiMnIn and NiMnGa alloys that are chemically and morphologically similar but crystallographically and physically very different. NiMnGa crystallizes in a Ni2In-type hexagonal structure, whereas NiMnIn is a cubic Heusler alloy. Both alloys yield a topological Hall effect contribution corresponding to bubble-type skyrmion spin structures, but it occurs in much lower magnetic fields in NiMnIn as compared to NiMnGa. The effect is unrelated to net Dzyaloshinskii-Moriya interactions, which are absent in both alloys due to their inversion-symmetric crystal structures. Based on magnetic-force microscopy, we explain the difference between the two alloys by magnetocrystalline anisotropy and uniaxial and cubic anisotropies yielding full-fledged and reduced topological Hall effects, respectively. Since NiMnIn involves small magnetic fields (0.02–0.3 kOe) at and above room temperature, it is of potential interest in spin electronics.
- 4 June 2019
- Published by American Physical Society (APS) in Physical Review Materials
- Vol. 3 (6) , 064403
Noncollinear spin structure in () from neutron diffractionNeutron powder diffraction has been used to investigate the spin structure of the hard-magnetic alloy (). The materials are produced by rapid quenching from the melt, they possess a hexagonal crystal structure, and they are nanocrystalline with crystallite sizes of the order of 40 nm. Projections of the magnetic moment onto both the crystalline axis and the basal plane were observed. The corresponding misalignment angle exhibits a nonlinear decrease with , which we explain as a micromagnetic effect caused by Fe-Co site disorder. The underlying physics is a special kind of random-anisotropy magnetism that leads to the prediction of power-law dependence of the misalignment angle on the crystallite size.- 4 June 2019
- Published by American Physical Society (APS) in Physical Review Materials
- Vol. 3 (6) , 064403
Noncollinear spin structure in () from neutron diffractionNeutron powder diffraction has been used to investigate the spin structure of the hard-magnetic alloy (). The materials are produced by rapid quenching from the melt, they possess a hexagonal crystal structure, and they are nanocrystalline with crystallite sizes of the order of 40 nm. Projections of the magnetic moment onto both the crystalline axis and the basal plane were observed. The corresponding misalignment angle exhibits a nonlinear decrease with , which we explain as a micromagnetic effect caused by Fe-Co site disorder. The underlying physics is a special kind of random-anisotropy magnetism that leads to the prediction of power-law dependence of the misalignment angle on the crystallite size.- 28 May 2019
- Published by American Physical Society (APS) in Physical Review B
- Vol. 99 (18) , 184438
Quantum phase transition and ferromagnetism inThe onset of ferromagnetism in cobalt-tin alloys is investigated experimentally and theoretically. The alloys were prepared by rapid quenching from the melt and form a modified hexagonal NiAs-type crystal structure for . The magnetic behavior is described analytically and by density-functional theory using supercells and the coherent-potential approximation. The excess of Co concentration , which enters the interstitial sites in the hypothetical NiAs-ordered parent alloy CoSn, yields a Griffiths-like phase and, above a quantum critical point , a quantum phase transition to ferromagnetic order. Quantum critical exponents are determined on the paramagnetic and ferromagnetic sides of the transition and related to the nature of the magnetism in itinerant systems with different types of chemical disorder.- 28 May 2019
- Published by American Physical Society (APS) in Physical Review B
- Vol. 99 (18) , 184438
Quantum phase transition and ferromagnetism inThe onset of ferromagnetism in cobalt-tin alloys is investigated experimentally and theoretically. The alloys were prepared by rapid quenching from the melt and form a modified hexagonal NiAs-type crystal structure for . The magnetic behavior is described analytically and by density-functional theory using supercells and the coherent-potential approximation. The excess of Co concentration , which enters the interstitial sites in the hypothetical NiAs-ordered parent alloy CoSn, yields a Griffiths-like phase and, above a quantum critical point , a quantum phase transition to ferromagnetic order. Quantum critical exponents are determined on the paramagnetic and ferromagnetic sides of the transition and related to the nature of the magnetism in itinerant systems with different types of chemical disorder.