Eduar Pérez
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Eduar Pérez has a total of 35 co-authors. Here are the top co-authors by number of shared publications:
- Ruben Hernan Castro Garcia
Grupo de Investigación en Fenómenos de Superficie—Michael Polanyi, Facultad de Minas, Universidad Nacional de Colombia—Sede Medellín, Medellín 050034, Colombia
5 shared publications - Gustavo Adolfo Maya Toro
Ecopetrol
4 shared publications - Henderson Ivan Quintero Pérez
Ecopetrol - ICP
4 shared publications - Julia Herrera
Ecopetrol - ICP
4 shared publications - Laura Maldonado Manrique
Desarrollo en tecnologías de Hidrocarburos, DTH SAS, Bucaramanga, Santander, Colombia
3 shared publications - Luis Prada
Desarrollo en tecnologías de Hidrocarburos, DTH SAS, Bucaramanga, Santander, Colombia
3 shared publications
Latest Publications
- 19 September 2025
- Published by Society of Petroleum Engineers (SPE) in SPE Journal
- Vol. 30 (11) , 7097-7111
Rapid Rheogram Prediction for Mechanically Degraded Hydrolyzed Polyacrylamide Solutions via Standard Viscosity Measurements
Summary: Reliable models predicting polymer solution rheology are crucial for chemical enhanced oil recovery (EOR). A primary challenge in polymer flooding is assessing mechanical degradation, which reduces oil recovery efficiency due to rheological changes. By measuring viscosity at 7.3 s−1 for both undegraded and degraded solutions, we derive expressions for the degraded volume fraction and Carreau-Yasuda model coefficients. This enables modeling rheological curves from 0.001 to 1,000 s−1 for both solution types. Comparison of model results with experimental and literature data shows satisfactory agreement. The model achieves a mean absolute percentage error (MAPE) below 10% for rheological curve estimation using standard field instruments, streamlining on-site decision-making.
- 19 September 2025
- Published by Society of Petroleum Engineers (SPE) in SPE Journal
- Vol. 30 (11) , 7097-7111
Rapid Rheogram Prediction for Mechanically Degraded Hydrolyzed Polyacrylamide Solutions via Standard Viscosity Measurements
Summary: Reliable models predicting polymer solution rheology are crucial for chemical enhanced oil recovery (EOR). A primary challenge in polymer flooding is assessing mechanical degradation, which reduces oil recovery efficiency due to rheological changes. By measuring viscosity at 7.3 s−1 for both undegraded and degraded solutions, we derive expressions for the degraded volume fraction and Carreau-Yasuda model coefficients. This enables modeling rheological curves from 0.001 to 1,000 s−1 for both solution types. Comparison of model results with experimental and literature data shows satisfactory agreement. The model achieves a mean absolute percentage error (MAPE) below 10% for rheological curve estimation using standard field instruments, streamlining on-site decision-making.
- Open Access
- 10 January 2024
- Published by MDPI AG in Nanomaterials
- Vol. 14 (2) , 156
Experimental Investigation of the Viscosity and Stability of Scleroglucan-Based Nanofluids for Enhanced Oil Recovery
Biopolymers emerge as promising candidates for enhanced oil recovery (EOR) applications due to their molecular structures, which exhibit better stability than polyacrylamides under harsh conditions. Nonetheless, biopolymers are susceptible to oxidation and biological degradation. Biopolymers reinforced with nanoparticles could be a potential solution to the issue. The nanofluids’ stability and performance depend on the nanoparticles’ properties and the preparation method. The primary objective of this study was to evaluate the effect of the preparation method and the nanoparticle type (SiO2, Al2O3, and TiO2) on the viscosity and stability of the scleroglucan (SG). The thickening effect of the SG solution was improved by adding all NPs due to the formation of three-dimensional structures between the NPs and the SG chains. The stability test showed that the SG + Al2O3 and SG + TiO2 nanofluids are highly unstable, but the SG + SiO2 nanofluids are highly stable (regardless of the preparation method). According to the ANOVA results, the preparation method and standing time influence the nanofluid viscosity with a statistical significance of 95%. On the contrary, the heating temperature and NP type are insignificant. Finally, the nanofluid with the best performance was 1000 ppm of SG + 100 ppm of SiO2_120 NPs prepared by method II.
- 10 January 2024
- Published by MDPI AG in Nanomaterials
- Vol. 14 (2) , 156
Open AccessExperimental Investigation of the Viscosity and Stability of Scleroglucan-Based Nanofluids for Enhanced Oil Recovery
Biopolymers emerge as promising candidates for enhanced oil recovery (EOR) applications due to their molecular structures, which exhibit better stability than polyacrylamides under harsh conditions. Nonetheless, biopolymers are susceptible to oxidation and biological degradation. Biopolymers reinforced with nanoparticles could be a potential solution to the issue. The nanofluids’ stability and performance depend on the nanoparticles’ properties and the preparation method. The primary objective of this study was to evaluate the effect of the preparation method and the nanoparticle type (SiO2, Al2O3, and TiO2) on the viscosity and stability of the scleroglucan (SG). The thickening effect of the SG solution was improved by adding all NPs due to the formation of three-dimensional structures between the NPs and the SG chains. The stability test showed that the SG + Al2O3 and SG + TiO2 nanofluids are highly unstable, but the SG + SiO2 nanofluids are highly stable (regardless of the preparation method). According to the ANOVA results, the preparation method and standing time influence the nanofluid viscosity with a statistical significance of 95%. On the contrary, the heating temperature and NP type are insignificant. Finally, the nanofluid with the best performance was 1000 ppm of SG + 100 ppm of SiO2_120 NPs prepared by method II.
- Open Access
- 22 April 2022
- Published by Universidad Nacional de Colombia in DYNA
- Vol. 89 (221) , 60-67
Mixture design of experiments for the behavior analysis of sulfonated polyacrylamide solutions (ATBS) with salinity, hardness, and concentration changes.
Un diseño de experimentos de mezcla (SCMD) fue usado para determinar el efecto de la dureza y salinidad del agua de preparación en la viscosidad final de una solución polimérica con modificaciones con unidades ATBS (Acrilamidas-Terbutil Sulfonadas). Con los resultados experimentales del SCMD se construyó un modelo cuadrático especial, y se implementó un modelo numérico que permite determinar la concentración de polímero necesaria para alcanzar la viscosidad deseada, dependiendo de la salinidad y dureza del agua de preparación. Adicionalmente, el modelo numérico desarrollado fue validado con datos experimentales de la literatura. Este puede predecir la concentración requerida de un polímero modificado con ATBS para alcanzar la viscosidad deseada con un 95% de confiabilidad en los rangos evaluados. El modelo numérico de Newton-Raphson desarrollado usando un SCMD es el primero reportado en la literatura que permite determinar la concentración de polímeros ATBS necesaria para conocer un rango de viscosidad.
- 22 April 2022
- Published by Universidad Nacional de Colombia in DYNA
- Vol. 89 (221) , 60-67
Open AccessMixture design of experiments for the behavior analysis of sulfonated polyacrylamide solutions (ATBS) with salinity, hardness, and concentration changes.
Un diseño de experimentos de mezcla (SCMD) fue usado para determinar el efecto de la dureza y salinidad del agua de preparación en la viscosidad final de una solución polimérica con modificaciones con unidades ATBS (Acrilamidas-Terbutil Sulfonadas). Con los resultados experimentales del SCMD se construyó un modelo cuadrático especial, y se implementó un modelo numérico que permite determinar la concentración de polímero necesaria para alcanzar la viscosidad deseada, dependiendo de la salinidad y dureza del agua de preparación. Adicionalmente, el modelo numérico desarrollado fue validado con datos experimentales de la literatura. Este puede predecir la concentración requerida de un polímero modificado con ATBS para alcanzar la viscosidad deseada con un 95% de confiabilidad en los rangos evaluados. El modelo numérico de Newton-Raphson desarrollado usando un SCMD es el primero reportado en la literatura que permite determinar la concentración de polímeros ATBS necesaria para conocer un rango de viscosidad.
- Open Access
- 17 December 2020
- Published by Instituto Colombiano del Petroleo in Ct&f - Ciencia, Tecnología Y Futuro
- Vol. 10 (2) , 115-129
CFD simulation of HPAM EOR solutions mechanical degradation by restrictions in turbulent flow
Polymer flooding is a widely used enhanced oil recovery (EOR) technology. The purpose of the polymer is to increase water viscosity to improve reservoir sweep efficiency. However, mechanical elements of the polymer injection facilities may impact the viscosity of the polymer negatively, decreasing it drastically. Mechanical degradation of the polymer occurs in case of flow restrictions with abrupt diameter changes in valves and control systems. Such flow restrictions may induce mechanical stresses along the polymer chain, which can result in its rupture. In this research, physical experiments and numerical simulations using CFD (Computational Fluid Dynamics) were used to propose a model for estimating the mechanical degradation for the flow of polymer solutions. This technique involves the calculation of velocity gradients, pressure drawdown, and polymer degradation of the fluid through geometry restriction. The simulations were validated through polymer injection experiments. The results show that with the greater volumetric flow and lower effective diameters, there is more mechanical degradation due to polymer shearing; nonetheless, this depends on the rheology properties inherent in each polymer in an aqueous solution. This method is suitable to estimate the mechanical degradation of the polymer solution in flooding facilities and accessories. Further, the results obtained could enhance the use of the polymer, calculating its actual mechanical degradation, minimizing it, or using it to support the development of new accessories.
- 17 December 2020
- Published by Instituto Colombiano del Petroleo in Ct&f - Ciencia, Tecnología Y Futuro
- Vol. 10 (2) , 115-129
Open AccessCFD simulation of HPAM EOR solutions mechanical degradation by restrictions in turbulent flow
Polymer flooding is a widely used enhanced oil recovery (EOR) technology. The purpose of the polymer is to increase water viscosity to improve reservoir sweep efficiency. However, mechanical elements of the polymer injection facilities may impact the viscosity of the polymer negatively, decreasing it drastically. Mechanical degradation of the polymer occurs in case of flow restrictions with abrupt diameter changes in valves and control systems. Such flow restrictions may induce mechanical stresses along the polymer chain, which can result in its rupture. In this research, physical experiments and numerical simulations using CFD (Computational Fluid Dynamics) were used to propose a model for estimating the mechanical degradation for the flow of polymer solutions. This technique involves the calculation of velocity gradients, pressure drawdown, and polymer degradation of the fluid through geometry restriction. The simulations were validated through polymer injection experiments. The results show that with the greater volumetric flow and lower effective diameters, there is more mechanical degradation due to polymer shearing; nonetheless, this depends on the rheology properties inherent in each polymer in an aqueous solution. This method is suitable to estimate the mechanical degradation of the polymer solution in flooding facilities and accessories. Further, the results obtained could enhance the use of the polymer, calculating its actual mechanical degradation, minimizing it, or using it to support the development of new accessories.
- Open Access
- 17 December 2020
- Published by Instituto Colombiano del Petroleo in Ct&f - Ciencia, Tecnología Y Futuro
- Vol. 10 (2) , 131-141
Experimental evaluation of the mechanical degradation of HPAM polymeric solutions used in Enhanced Oil Recovery
With the design of experiments (DoE), this study analyses the influence of physical (capillary diameter and pressure drop) and chemical variables (salinity, polymer concentration, and molecular weight) on the mechanical degradation of partially hydrolyzed polyacrylamide-type polymer solutions (HPAM) used in enhanced oil recovery processes. Initially, with the help of a fractional factorial design (2k-p), the variables with the most significant influence on the polymer's mechanical degradation were found. The experimental results of the screening demonstrate that the factors that statistically influence the mechanical degradation are the molecular weight, the diameter of the capillary, and the pressure differential. Subsequently, a regression model was developed to estimate the degradation percentages of HPAM polymer solutions as a function of the significant factors influencing the mechanical degradation of polymer solutions. This model had a 97.85% fit for the predicted values under the experimental conditions. Likewise, through the optimization developed by the Box Behnken response surface methodology, it was determined that the pressure differential was the most influential factor. This variable was followed by the capillary diameter, where less than 50% degradation rates are obtained with low polymer molecular weight (6.5 MDa), pressure differentials less than 500 psi, and diameters of the capillary greater than 0.125 inches.
- 17 December 2020
- Published by Instituto Colombiano del Petroleo in Ct&f - Ciencia, Tecnología Y Futuro
- Vol. 10 (2) , 131-141
Open AccessExperimental evaluation of the mechanical degradation of HPAM polymeric solutions used in Enhanced Oil Recovery
With the design of experiments (DoE), this study analyses the influence of physical (capillary diameter and pressure drop) and chemical variables (salinity, polymer concentration, and molecular weight) on the mechanical degradation of partially hydrolyzed polyacrylamide-type polymer solutions (HPAM) used in enhanced oil recovery processes. Initially, with the help of a fractional factorial design (2k-p), the variables with the most significant influence on the polymer's mechanical degradation were found. The experimental results of the screening demonstrate that the factors that statistically influence the mechanical degradation are the molecular weight, the diameter of the capillary, and the pressure differential. Subsequently, a regression model was developed to estimate the degradation percentages of HPAM polymer solutions as a function of the significant factors influencing the mechanical degradation of polymer solutions. This model had a 97.85% fit for the predicted values under the experimental conditions. Likewise, through the optimization developed by the Box Behnken response surface methodology, it was determined that the pressure differential was the most influential factor. This variable was followed by the capillary diameter, where less than 50% degradation rates are obtained with low polymer molecular weight (6.5 MDa), pressure differentials less than 500 psi, and diameters of the capillary greater than 0.125 inches.
- 4 March 2019
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 947, 52-57
Experimental Study on a Chemisorption Refrigeration System Prototype Using Expanded Graphite/Activated Carbon/Lithium Chloride-Ammonia Working Pair in a Solution of 25% NH3
This paper presents the experimental results given by the operation of a chemical sorption refrigeration system using Expanded Graphite/Activated Carbon/Lithium Chloride (AC/GE/LiCl)-Adsorbent (NH3 in solution with a 25% concentration). Experimental protocol with the characteristics of the experimental rig developed, working pair specifications and the procedure that has developed in the process is described in detail. Results are presented for different behaviors of the system, where the desorption stage is driven by forced convection. Measurements of the thermal variables of the system show that the adsorption-desorption cycles in the test accomplished, with high and low-pressure zones clearly defined. The cooling effects for the pair material studied have the expected behavior for the mixture proposed.
- 4 March 2019
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 947, 52-57
Experimental Study on a Chemisorption Refrigeration System Prototype Using Expanded Graphite/Activated Carbon/Lithium Chloride-Ammonia Working Pair in a Solution of 25% NH3
This paper presents the experimental results given by the operation of a chemical sorption refrigeration system using Expanded Graphite/Activated Carbon/Lithium Chloride (AC/GE/LiCl)-Adsorbent (NH3 in solution with a 25% concentration). Experimental protocol with the characteristics of the experimental rig developed, working pair specifications and the procedure that has developed in the process is described in detail. Results are presented for different behaviors of the system, where the desorption stage is driven by forced convection. Measurements of the thermal variables of the system show that the adsorption-desorption cycles in the test accomplished, with high and low-pressure zones clearly defined. The cooling effects for the pair material studied have the expected behavior for the mixture proposed.
- Open Access
- 14 December 2016
- Published by Editorial Pontificia Universidad Javeriana in Ingenieria y Universidad
- Vol. 21 (1)
ANALISIS DE LA CANTIDAD DE FLUJO DE CALOR CIRCUNDANTE ENTRE LOS CANALES DE REFRIGERACIÓN EN TRES DISCOS DE FRENO AUTOVENTILADOS
ANALISIS DE LA CANTIDAD DE FLUJO DE CALOR CIRCUNDANTE ENTRE LOS CANALES DE REFRIGERACIÓN EN TRES DISCOS DE FRENO AUTOVENTILADOS
- 14 December 2016
- Published by Editorial Pontificia Universidad Javeriana in Ingenieria y Universidad
- Vol. 21 (1)
Open AccessANALISIS DE LA CANTIDAD DE FLUJO DE CALOR CIRCUNDANTE ENTRE LOS CANALES DE REFRIGERACIÓN EN TRES DISCOS DE FRENO AUTOVENTILADOS
ANALISIS DE LA CANTIDAD DE FLUJO DE CALOR CIRCUNDANTE ENTRE LOS CANALES DE REFRIGERACIÓN EN TRES DISCOS DE FRENO AUTOVENTILADOS