JBJunfu Bu

Junfu Bu

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Junfu Bu has a total of 63 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    High plating currents without dendrites at the interface between a lithium anode and solid electrolyte

    by Dominic L. R. Melvin, Marco Siniscalchi, Dominic Spencer-Jolly, Bingkun Hu, Ziyang Ning, Shengming Zhang, Junfu Bu, Shashidhara Marathe, Anne Bonnin, Johannes Ihli, et al.

    Avoiding lithium dendrites at the lithium/ceramic electrolyte interface and, as a result, avoiding cell short circuit when plating at practical current densities remains a significant challenge for all-solid-state batteries. Typically, values are limited to around 1 mA cm −2 , even, for example, for garnets with a relative density of >99%. It is not obvious that simply densifying ceramic electrolytes will deliver high plating currents. Here we show that plating currents of 9 mA cm −2 can be achieved without dendrite formation, by densifying argyrodite, Li 6 PS 5 Cl, to 99%. Changes in the microstructure of Li 6 PS 5 Cl on densification from 83 to 99% were determined by focused ion beam-scanning electron microscopy tomography and used to calculate their effect on the critical current density (CCD). Modelling shows that not all changes in microstructure with densification act to increase CCD. Whereas smaller pores and shorter cracks increase CCD, lower pore population and narrower cracks act to decrease CCD. Calculations show that the former changes dominate over the latter, predicating an overall increase in CCD, as observed experimentally.


  • Open Access

    High plating currents without dendrites at the lithium anode/solid electrolyte interface

    by Dominic L. R. Melvin, Marco Siniscalchi, Dominic Spencer-Jolly, Bingkun Hu, Ziyang Ning, Shengming Zhang, Junfu Bu, Shashidhara Marathe, Anne Bonnin, Johannes Ihli, et al.

    Avoiding lithium dendrites at the lithium/ceramic electrolyte interface and as a result avoiding cell short-circuit when plating at practical current densities remains a significant challenge for all-solid-state batteries. Typically, values are limited to around 1 mA cm-2, even, for example, for garnets with a relative density of >99%. It is not obvious that simply densifying ceramic electrolytes will deliver high plating currents. Here we show that plating currents of 9 mA cm-2 can be achieved without dendrite formation, by densifying Argyrodite, Li6PS5Cl, to 99%. Changes in the microstructure of Li6PS5Cl on densification from 83 to 99% were determined by FIB-SEM tomography and used to calculate their effect on the critical current density (CCD). Not all changes in microstructure with densification act to increase CCD. While smaller pores and shorter cracks increase CCD, lower pore population and narrower cracks act to decrease CCD. Calculations show that the former changes dominate over the latter, predicating an overall increase in CCD, as observed experimentally.

  • Open Access

    Interfaces between Ceramic and Polymer Electrolytes: A Comparison of Oxide and Sulfide Solid Electrolytes for Hybrid Solid-State Batteries

    by Dominic Spencer Jolly, Dominic L. R. Melvin, Isabella D. R. Stephens, Rowena H. Brugge, Shengda D. Pu, Junfu Bu, Ziyang Ning, Gareth O. Hartley, Paul Adamson, Patrick S. Grant, et al.

    Hybrid solid-state batteries using a bilayer of ceramic and solid polymer electrolytes may offer advantages over using a single type of solid electrolyte alone. However, the impedance to Li+ transport across interfaces between different electrolytes can be high. It is important to determine the resistance to Li+ transport across these heteroionic interfaces, as well as to understand the underlying causes of these resistances; in particular, whether chemical interphase formation contributes to giving high resistances, as in the case of ceramic/liquid electrolyte interfaces. In this work, two ceramic electrolytes, Li3PS4 (LPS) and Li6.5La3Zr1.5Ta0.5O12 (LLZTO), were interfaced with the solid polymer electrolyte PEO10:LiTFSI and the interfacial resistances were determined by impedance spectroscopy. The LLZTO/polymer interfacial resistance was found to be prohibitively high but, in contrast, a low resistance was observed at the LPS/polymer interface that became negligible at a moderately elevated temperature of 50 °C. Chemical characterization of the two interfaces was carried out, using depth-profiled X-ray photoelectron spectroscopy and time-of-flight secondary ion mass spectrometry, to determine whether the interfacial resistance was correlated with the formation of an interphase. Interestingly, no interphase was observed at the higher resistance LLZTO/polymer interface, whereas LPS was observed to react with the polymer electrolyte to form an interphase.


  • Open Access

    Single‐Step Spray Printing of Symmetric All‐Organic Solid‐State Batteries Based on Porous Textile Dye Electrodes

    by Puiki Leung, Junfu Bu, Pablo Quijano Velasco, Matthew R. Roberts, Nicole Grobert, Patrick S. Grant

    A symmetric solid‐state battery based on organic porous electrodes is fabricated using scalable spray‐printing. The active electrode material is based on a textile dye (disperse blue 134 anthraquinone) and is capable of forming divalent cations and anions in oxidation and reduction processes. The resulting molecule can be used in both negative and positive electrode reactions. After spray printing an inter‐connected pore honeycomb electrode, a solid‐state electrolyte (σLi: × 10−4 S cm−1) based on a polymeric ionic liquid is spray‐printed as a second layer and infiltrated through the porous electrodes. A symmetric all‐organic battery is then formed with the addition of another identical set of electrode and electrolyte layers. Both density functional theory calculations and charge‐discharge profiles show that the potentials for the negative and positive electrode reactions are amongst the lowest (≈2.0 V vs Li) and the highest (≈3.5 V vs Li), respectively, for quinone‐type molecules. Over the C‐rate range 0.2 to 5 C, the battery has a discharge cell voltage of more than 1 V even up to 250 charge‐discharge cycles and capacities are in the range 50–80 mA h g−1 at 0.5 C.


  • Open Access

    Co-spray printing of LiFePO4 and PEO-Li1.5Al0.5Ge1.5(PO4)3 hybrid electrodes for all-solid-state Li-ion battery applications

    by Junfu Bu, Puiki Leung, Chun Huang, Sang Ho Lee, Patrick S. Grant

    LiFePO4 (LFP) electrodes for Li-ion battery applications were prepared by spray printing. By optimising the substrate temperature, solvent ratio and electrode material concentration, a honeycomb pore structure was produced over a large area electrode. In a liquid electrolyte, the honeycomb structured LFP electrode showed improved cycling performance at high C-rate due to shortened pore pathways and improved Li mobility. In a solid-state configuration, a PEO(LITFSI)-Li1.5Al0.5Ge1.5(PO4)3 (PEO-LAGP) based solid electrolyte was either spray printed on top of the LFP and/or interleaved within sub-layers of the LFP electrode, for both non-honeycomb and honeycomb pore morphologies. Cross-sectional scanning electron microscope (SEM) and energy-dispersive X-ray spectroscopy (EDS) mapping combined with electrochemical impedance spectroscopy (EIS) testing showed that the honeycomb electrode with inter-leaved sub-layers of solid-state electrolyte improved interfacial contact between the electrode and electrolyte. When coupled with Li foil in a solid-state Li ion battery configuration, the honeycomb interleaved electrode also showed the best performance in terms of capacity and cycle stability at all testing temperatures, showing capability that exceeded previously reported performance.


  • A new Dy-doped BaCeO 3 –BaZrO 3 proton-conducting material as a promising electrolyte for reversible solid oxide fuel cells

    by Julia Lyagaeva, Nikolay Danilov, Gennady Vdovin, Junfu Bu, Dmitry Medvedev, Anatoly Demin, Panagiotis Tsiakaras

    The present work describes the features of the synthesis and physicochemical and electrical properties of a new Dy-doped BaCeO 3 –BaZrO 3 proton-conducting electrolyte as well as its application in a reversible solid oxide fuel cell.


  • The effect of NiO on the conductivity of BaZr0.5Ce0.3Y0.2O3−δ based electrolytes

    by Junfu Bu, Pär Göran Jönsson, Zhe Zhao

    The effects of NiO on the sintering behaviors, morphologies and conductivities of BaZr0.5Ce0.3Y0.2O3−δ (BZCY532) based electrolytes were systematically investigated. 1 wt% NiO powder was added by different methods during the sample preparation: (i) added during ball-milling before a powder mixture calcination (named BZCY(Ni)532), (ii) no NiO addition in the whole preparation procedure (named BZCY532) and (iii) added after a powder mixture calcination (named BZCY532(Ni)). The conductivities of these three kinds of dense BZCY532 ceramics were investigated in dry air, wet N2 and wet H2 atmospheres, respectively. Moreover, the electronic contributions to the total conductivities were also identified in a broad oxygen partial pressure range. According to the achieved results, it can be concluded that the dense BZCY(Ni)532 ceramics showed the best enhanced oxygen and proton conductivities, followed by the BZCY532(Ni) and BZCY532 ceramics. Furthermore, the BZCY(Ni)532 and BZCY532 ceramics showed a tiny electronic conductivity, when the testing temperatures were lower than 800 °C. However, the BZCY532(Ni) ceramics revealed an obvious electronic conduction when they were tested at temperatures of 600–800 °C. Therefore, it is preferable to add the NiO during powder preparation, which can lower the sintering temperature and also increase the conductivity of BZCY532-based electrolytes.