He Huang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
He Huang has a total of 51 co-authors. Here are the top co-authors by number of shared publications:
Fu-Ling Guan
College of Civil Engineering and Architecture
3 shared publications- Kai Zhang
Northwestern Polytechnical University
3 shared publications Liyuan Qi
3 shared publications- Mengmei Mei3 shared publications
Xianghui Cao
3 shared publicationsYan Xu
3 shared publications
Latest Publications
- 11 September 2026
- Published by Elsevier in Journal of the Mechanics and Physics of Solids
- Vol. 218
Anomalous wave velocity characteristics in truncated octahedron tensegrity structures
- 11 September 2026
- Published by Elsevier in Journal of the Mechanics and Physics of Solids
- Vol. 218
Anomalous wave velocity characteristics in truncated octahedron tensegrity structures
- 18 June 2026
- Published by Elsevier in Acta Astronautica
- Vol. 248, 1025-1041
Optimal design and gravity offloading deployment test of large-aperture petal-type deployable solid surface antenna
- 18 June 2026
- Published by Elsevier in Acta Astronautica
- Vol. 248, 1025-1041
Optimal design and gravity offloading deployment test of large-aperture petal-type deployable solid surface antenna
- 20 May 2026
- Published by Elsevier in Ocean Engineering
- Vol. 361
Deformation reconstruction of pipes under impact load using inverse finite element method based on iBeam2 elements
- 20 May 2026
- Published by Elsevier in Ocean Engineering
- Vol. 361
Deformation reconstruction of pipes under impact load using inverse finite element method based on iBeam2 elements
- 17 April 2026
- Published by Elsevier in Thin-Walled Structures
- Vol. 227
Modal characteristics of the mirror-assembled six-bar rotational tensegrity module
- 17 April 2026
- Published by Elsevier in Thin-Walled Structures
- Vol. 227
Modal characteristics of the mirror-assembled six-bar rotational tensegrity module
- Open Access
- 2 February 2026
- Published by Elsevier in SSRN Electronic Journal
Optimal Design and Ground Gravity Offloading Deployment Test for a Large-aperture Petal-type Deployable Solid Surface Antenna
Deployable Solid Surface Antennas (DSSAs) exhibit superior stiffness, surface accuracy, and dynamic performance, yet the package efficiency remains limited due to rigid panel configurations. This paper focuses on the optimization and ground test of a Large-aperture Petal-type Deployable Solid Surface Antenna (LPDSSA). A genetic algorithm is employed to optimize key design parameters of a dual-axis deployment mechanism, achieving an optimal package ratio under non-interference constraints. Then, an equivalent single-axis deployment mechanism for a scaled model is derived via coordinate transformation. To validate the model under simulated microgravity conditions, a cable suspension-based gravity offloading system is developed for ground deployment test of a full-scale 2-petal prototype. Experimental and simulation results demonstrate that the proposed deployment mechanism has reliable functions and maintains high surface accuracy in the fully deployed state. Additionally, a closed-loop Torque Observation - Force Control System (TOFCS) with a PI controller is implemented to dynamically adjust the offloading force, significantly reducing the torque on the rotation axis and improving deployment smoothness. The study provides a comprehensive design and testing framework that effectively bridges ground verification and in-orbit performance for future LPDSSAs.
- 2 February 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessOptimal Design and Ground Gravity Offloading Deployment Test for a Large-aperture Petal-type Deployable Solid Surface Antenna
Deployable Solid Surface Antennas (DSSAs) exhibit superior stiffness, surface accuracy, and dynamic performance, yet the package efficiency remains limited due to rigid panel configurations. This paper focuses on the optimization and ground test of a Large-aperture Petal-type Deployable Solid Surface Antenna (LPDSSA). A genetic algorithm is employed to optimize key design parameters of a dual-axis deployment mechanism, achieving an optimal package ratio under non-interference constraints. Then, an equivalent single-axis deployment mechanism for a scaled model is derived via coordinate transformation. To validate the model under simulated microgravity conditions, a cable suspension-based gravity offloading system is developed for ground deployment test of a full-scale 2-petal prototype. Experimental and simulation results demonstrate that the proposed deployment mechanism has reliable functions and maintains high surface accuracy in the fully deployed state. Additionally, a closed-loop Torque Observation - Force Control System (TOFCS) with a PI controller is implemented to dynamically adjust the offloading force, significantly reducing the torque on the rotation axis and improving deployment smoothness. The study provides a comprehensive design and testing framework that effectively bridges ground verification and in-orbit performance for future LPDSSAs.
- 11 September 2024
- Published by Elsevier in Measurement
- Vol. 241
Dynamic analysis and shape sensing of pipes subjected to water hammer by the inverse finite element method
- 11 September 2024
- Published by Elsevier in Measurement
- Vol. 241
Dynamic analysis and shape sensing of pipes subjected to water hammer by the inverse finite element method
- 2 March 2024
- Published by Elsevier in Structures
- Vol. 61
Design and experimental verification of an adjustable constant-force mechanism
- 2 March 2024
- Published by Elsevier in Structures
- Vol. 61
Design and experimental verification of an adjustable constant-force mechanism
- Open Access
Multi-Objective Optimization Design of an Origami-Inspired Combined Cushion Airbag
To improve the cushioning performance of soft-landing systems, a novel origami-inspired combined cushion airbag is proposed. The geometry size, initial pressure, and exhaust vent area of the cushion airbags are designed preliminarily using a theoretical model. The finite element models, including the returnable spacecraft and cushion airbags, are established via the control volume method (CVM) to analyze the impact dynamic behavior and cushioning performance during the landing attenuation process. The cushioning performance of the cushion airbags in complex landing environments are studied to investigate the influence of horizontal velocity, lateral velocity and nonhorizontal landing surfaces. Four design parameters of the cushion airbags, including the initial pressure, venting threshold pressure, exhaust vent area and polygon edge number, are employed to study their influence on the cushioning performance. A multi-objective optimization model of the cushion airbags based on the neural network and multi-objective water cycle algorithm is established to realize the rapid optimization design. The Pareto front of the maximum overload and specific energy absorption is obtained. The analysis results show that the maximum overload of the proposed combined cushion airbags is 7.30 g. The system with the anti-rollover design can avoid rollover and achieve outstanding cushioning performance in complex landing environments. The maximum overload of the returning spacecraft is decreased by 16.4% from 7.30 g to 6.10 g after multi-objective optimizations. This study could provide the technical support for the soft-landing system design of returnable spacecrafts.
Open AccessMulti-Objective Optimization Design of an Origami-Inspired Combined Cushion Airbag
To improve the cushioning performance of soft-landing systems, a novel origami-inspired combined cushion airbag is proposed. The geometry size, initial pressure, and exhaust vent area of the cushion airbags are designed preliminarily using a theoretical model. The finite element models, including the returnable spacecraft and cushion airbags, are established via the control volume method (CVM) to analyze the impact dynamic behavior and cushioning performance during the landing attenuation process. The cushioning performance of the cushion airbags in complex landing environments are studied to investigate the influence of horizontal velocity, lateral velocity and nonhorizontal landing surfaces. Four design parameters of the cushion airbags, including the initial pressure, venting threshold pressure, exhaust vent area and polygon edge number, are employed to study their influence on the cushioning performance. A multi-objective optimization model of the cushion airbags based on the neural network and multi-objective water cycle algorithm is established to realize the rapid optimization design. The Pareto front of the maximum overload and specific energy absorption is obtained. The analysis results show that the maximum overload of the proposed combined cushion airbags is 7.30 g. The system with the anti-rollover design can avoid rollover and achieve outstanding cushioning performance in complex landing environments. The maximum overload of the returning spacecraft is decreased by 16.4% from 7.30 g to 6.10 g after multi-objective optimizations. This study could provide the technical support for the soft-landing system design of returnable spacecrafts.
- Open Access
- 23 October 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (20) , 11602
Parametric Design and Shape Sensing of Geared Back Frame Shell Structure for Floating Cylindrical Reflector Antenna off the Coast
At present, numerous reflector antennas have been constructed worldwide on land. However, there are few applications of reflector antennas directly set off the coast. To expand the application region of reflector antennas, a floating cylindrical reflector antenna (FCRA) driven by the moving mass was developed to implement the elevation angle adjustment. Firstly, the structure design is introduced in detail. The design parameters are stated and analyzed to obtain the kinematic relationship while considering the water surface constraint. Then, the effects of each variable on the rotation capacity and structural stability are discussed. Further, the feasibility of the elevation angle adjustment process is demonstrated by using a prototype model test and software simulation. Finally, the deformation analyses and shape sensing of the back frame are carried out on the basis of the inverse finite element method (iFEM). We concluded that this new structure is feasible and expected to sit off the coast. In addition, the iFEM algorithm with sub-region reconstruction was proved to be suitable for the shape sensing of the over-constrained FCRA during the angle adjustment process via several quasi-static sampling moments.
- 23 October 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (20) , 11602
Open AccessParametric Design and Shape Sensing of Geared Back Frame Shell Structure for Floating Cylindrical Reflector Antenna off the Coast
At present, numerous reflector antennas have been constructed worldwide on land. However, there are few applications of reflector antennas directly set off the coast. To expand the application region of reflector antennas, a floating cylindrical reflector antenna (FCRA) driven by the moving mass was developed to implement the elevation angle adjustment. Firstly, the structure design is introduced in detail. The design parameters are stated and analyzed to obtain the kinematic relationship while considering the water surface constraint. Then, the effects of each variable on the rotation capacity and structural stability are discussed. Further, the feasibility of the elevation angle adjustment process is demonstrated by using a prototype model test and software simulation. Finally, the deformation analyses and shape sensing of the back frame are carried out on the basis of the inverse finite element method (iFEM). We concluded that this new structure is feasible and expected to sit off the coast. In addition, the iFEM algorithm with sub-region reconstruction was proved to be suitable for the shape sensing of the over-constrained FCRA during the angle adjustment process via several quasi-static sampling moments.