Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Xijia Wu has a total of 41 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    A unified formulation of fatigue life under unbalanced cyclic loading profile

    by Xijia Wu

    In this study, a unified formulation is derived for fatigue crack nucleation under general unbalanced cyclic loading profiles, and it is combined with the integrated creep-fatigue theory (ICFT) to give a physics-based theoretical description from very low cycle fatigue to high cycle fatigue, rather than building up by empirical rules. Using several engineering alloys as illustrative examples, the model has been shown to effectively include the effects of mean stress /ratcheting strain, and monotonic plastic damage in metal fatigue. For small-amplitude loading cases, it works equivalently well as the SWT model, but it goes beyond the empirical data-collapsing method to predict fatigue life based on the material basic physical/mechanical properties such as the elastic modulus, Poisson’s ratio, surface energy, Burgers vector without the need of data regression. Therefore, it offers a unified tool for fatigue design and analysis.

  • Computational Prediction of Total Fatigue Life With an Integrated Approach

    by Siqi Li, Zhong Zhang, Rong Liu, Xijia Wu

    This research tackles the fundamental issue of computational fatigue studies by developing an effective approach that combines the crystal plasticity finite element method (CPFEM) with the Tanaka–Mura–Wu (TMW) model for crack nucleation and the Tomkins model for fatigue crack propagation, to provide Class-A predictions of the total coupon-fatigue life (crack initiation and growth lives) for a nickel-based superalloy, Haynes 282. To gain a statistical significance accounting for the microstructure inhomogeneity, 11 3D Representative Volume Elements (RVEs) are created utilizing Dream.3d to represent the polycrystalline material with different grain structures and orientations in equivalence to the experimental microstructure data. The CPFEM model is calibrated to the material's hysteresis behavior, and then, the microstructural plastic strain from the RVE is taken to calculate the fatigue life. The prediction is found in good agreement with the fatigue test data, validating the effectiveness of the proposed approach in predicting the fatigue life and scatter due to microstructural variability for Haynes 282 alloy. In addition, the effects of local grain attributes including grain orientation and adjacent grain arrangement on fatigue crack nucleation are analyzed quantitatively. It is suggested that grain orientation influences plastic deformation by inducing the active slip systems, and the slip transfer across grain boundaries also contributes to fatigue crack nucleation.


  • Open Access

    Fatigue Life Prediction of a SAE Keyhole Specimen as a Subcase of Certification by Analysis

    by Xijia Wu, Zhong Zhang, Dany Paraschivoiu

    To advance the technology of Certification by Analysis (CbA), as called for by the aerospace industry, the fatigue problems of SAE keyhole specimens are analyzed to demonstrate a subcase of CbA. First, phenomena identification and ranking table (PIRT) analysis is performed. Second, modeling of the key phenomena is conducted, and finally, verification and validation with the experimental results are achieved. In particular, the elastic/elastoplastic stress distributions in the keyhole specimens are obtained using the finite element method (FEM). Plasticity correction for stress/strain at the notch root is made using the modified Neuber’s rule along with the Ramberg–Osgood equation. The low cycle fatigue (LCF) crack nucleation life is analytically predicted using the modified Tanaka–Mura model, a.k.a. the TMW model, given the material’s elastic modulus, Poisson’s ratio, Burgers vector, and surface energy, without the need for coupon fatigue data regression. The Tomkins equation is used to simulate plastic crack growth within the notch plastic zone. The above analytical life predictions are validated against the SAE keyhole specimen tests, becoming the first successful case of fatigue CbA at a sub-element level.


  • Open Access

    Creep Phenomena, Mechanisms, and Modeling of Complex Engineering Alloys

    by Xijia Wu, Rong Liu, Fadila Khelfaoui

    Metal creep has been a subject of extensive study for more than 110 years because it affects the useful life of engineering components operating at high temperatures. This is even more true with ever-increasing operating temperatures of propulsion/power-generation systems and the environmental regulations to reduce greenhouse emissions. This review summarizes the recent development in creep modeling with regards to creep strain evolution, creep rate, creep ductility, creep life, and fracture mode, attempting to provide a comprehensive mechanism-based framework to address all the important creep phenomena and the long-standing issue of long-term creep life prediction with microstructural evolution and environmental effects.


  • Open Access

    Creep Phenomena, Mechanisms and Modeling

    by Xijia Wu, Rong Liu, Fadila Khelfaoui

    Metal creep has been a subject of extensive study for more than 110 years, because it affects the useful life of engineering components operating at high temperatures. It is even more so with ever-increasing operating temperatures of propulsion/power-generation systems by the environmental regulations to reduce greenhouse emissions. This review summaries the recent development in creep modeling with regards to creep strain evolution, creep rate, creep ductility, creep life and fracture mode, attempting to provide a comprehensive mechanism-based framework to address all the important creep phenomena and the long-standing issue of long-term creep life prediction with microstructural evolution and environmental effects.


  • Creep Performance Study of Inconel 740H Weldment Based on Microstructural Deformation Mechanisms

    by Xijia Wu, Rong Liu, Xiaozhou Zhang, Xueyao Wu, Fadila Khelfaoui, Joe Zhang

    The creep behavior of Inconel 740H weldment at the temperature of 760 °C is investigated experimentally and analytically using the deformation-mechanism-based true stress (DMTS) model. The Inconel 740H weldment specimens are prepared with the gas tungsten arc welding technique. Creep testing is performed on the Inconel 740H weldment specimens under a range of stress levels from 190 MPa to 447 MPa at the temperature of 760 °C. The DMTS model is employed to analyze the creep curves and creep rates. The model parameters for Inconel 740H weldment are determined from the analyses of the creep testing data in combination with that from the previous studies of similar materials based on the same creep mechanisms that involve grain boundary sliding and intragranular dislocation climb-plus-glide with dislocation multiplication. The creep life predictions of the DMTS model for Inconel 740H weldment agree very well with creep rupture test data within a temperature range of 700–800 °C. The fractured surfaces and longitudinal sections of creep-tested Inconel 740H weldment specimens are examined using scanning electron microscopy, which corroborates the DMTS model inference that the creep failure of Inconel 740H weldment is in a mode of predominantly intergranular fracture. The present study suggests that grain boundary sliding is the most significant controlling factor for the creep failure of Inconel 740H weldment.


  • Creep behavior and life prediction of a reactor pressure vessel steel above phase‐transformation temperature via a deformation mechanism‐based creep model

    by Chuanyang Lu, Peng Wang, Silu Zheng, Xijia Wu, Rong Liu, Yanming He, Jianguo Yang, Zengliang Gao, Shan‐Tung Tu

    For nuclear power generation as a carbon‐neutral energy source, in‐vessel retention (IVR) must be implemented to maintain the structural integrity of nuclear reactor pressure vessel (RPV) for more than 72 h under severe accidental conditions. This technology requires accurate prediction of creep deformation and life of RPV material being operated under pressure and extremely high‐temperature gradient. The current work develops a simplified deformation‐mechanism‐based true‐stress (DMTS) model for creep behavior/life‐prediction of SA508 Gr.3 steel, a typical RPV material, above the phase transformation temperatures (800–1000°C). This model is used to evaluate the time to specific creep strain (t3% and t5%) and rupture (tr), in comparison with popular empirical methods such as Orr–Sherby–Dorn (OSD) and Larson–Miller (LM). The simplified DMTS model achieves an excellent agreement with the experimental observations. The controlling deformation mechanisms are also discussed by metallurgical examinations, which provide the physical premise for the model development and application.


  • Open Access

    An Overview of Self-Heating Phenomena and Theory Related to Damping and Fatigue of Metals

    by Xijia Wu, Lucy Li

    This paper presents an overview of the self-heating phenomena and the continuum thermodynamics framework related to the damping and fatigue of metals. The self-heating process under cyclic loading generally undergoes three phases: Phase I with gradually increasing temperature to a stabilized or steady-state in Phase II, followed by Phase III with an accelerated temperature increase until the test sample ruptures. Although energy dissipation and heat generation are all captured by the first law of thermodynamics, the functional form of the heat source(s) with entropy change is not formulated for engineering materials. Experimentally, infrared (IR) thermographic techniques can measure the surface temperature variation during constant-amplitude fatigue testing. The observed relationship between the stabilization temperature or temperature increase rate and the applied stress amplitude is often used to infer the fatigue endurance limit, above which point heat generation from “damage” leads to acceleration of self-heating. The IR thermographic fatigue testing offers a rapid alternative method to assess the material’s fatigue strength. But, the full physical interpretation of the phenomena remains a challenge. On the other hand, the Tanaka-Mura–Wu model is introduced to describe fatigue crack nucleation via accumulation of dislocation dipole pile-up, which provides a class-A prediction (forecast before even happening) for fatigue crack nucleation life in terms of the material’s elastic modulus, Burgers vector, surface energy, and the loading parameter such as cyclic stress/strain range. Then, the release of dislocation dipole pile-up energy to form new crack surfaces is brought into the energy argument. With the inclusion of crack formation energy in the first law of thermodynamics, a unified framework of deformation, damping, fatigue, and self-heating may be established for structural design.


  • Open Access

    Characterization of the Microstructure and Surface Roughness Effects on Fatigue Life Using the Tanaka–Mura–Wu Model

    by Xijia Wu, Philippe Kanz, Hassan Mahmoud, Jason Millar, Peyman Shabani, Jose Martinez Torres

    Additive manufacturing (AM) has drawn tremendous interest in engineering applications because it offers almost unlimited possibilities of innovative structural design to save weight and optimize performance. However, fatigue properties are one of the limiting factors for structural applications of AM materials. The recently developed Tanaka–Mura–Wu (TMW) model is modified to include the microstructure and surface roughness factors, in addition to the material’s elastic modulus, surface energy and Burgers vector, to predict the fatigue curves as functions of stress or plastic strain for several typical AM materials as well as their conventional (wrought) counterpart. Furthermore, with statistical characterization of the microstructural effect, the model can be established to evaluate fatigue design allowables.


  • Low-Cycle Fatigue Life of Continuously Cyclic-Hardening Material

    by Zhong Zhang, Xijia Wu

    A general fatigue life equation is derived by modifying the Tanaka-Mura-Wu dislocation pile-up model for variable strain-amplitude fatigue processes, where the fatigue crack nucleation life is expressed in terms of the root-mean-square of plastic strain range. Low-cycle fatigue tests were conducted on an austenitic stainless steel. At 400 °C and 600 °C, the material exhibits continuously cyclic-hardening behavior. The root-mean-square of plastic strain ranges is evaluated from the experimental data for each test condition at strain rates ranging from 0.0002/s to 0.02/s. The variable-amplitude Tanaka-Mura-Wu model is found to be in good agreement with the low-cycle fatigue (LCF) data, which effectively proves Miner's rule on the stored plastic strain energy basis.