QXQingjin Xu

Qingjin Xu

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Qingjin Xu has a total of 245 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Electromagnetic properties of iron-based superconducting uninsulated double pancake coils and their comparison with REBCO coils

    by Fan Ren, Chunyan Li, Yanchang Zhu, Cong Liu, Jin Zhou, Qingyuan Li, Rui Kang, Ling Zhao, Chengtao Wang, Juan Wang, et al.

    Iron-based superconductors show great potential for high-field magnet applications. The electromagnetic properties of iron-based superconducting (IBS) uninsulated coils are crucial for their future practical applications, yet characteristics such as charging delay and turn-to-turn contact resistivity ( R ct ) remain poorly understood. To address this, we fabricated metal-insulation (MI) and no-insulation (NI) IBS double pancake coils and systematically tested their charging and sudden-discharging behaviors. Experimental results revealed that the R ct of the IBS-MI coil is 6.3 times higher than that of the IBS-NI coil, along with a significantly shorter charging delay. Moreover, an interesting phenomenon was discovered: the R ct of uninsulated IBS coils is much lower than that of the REBCO coils reported in previous studies. For rigorous verification of this finding, MI and NI REBCO coils were prepared and subjected to charging and sudden-discharging tests. Through comparison, it is found that the R ct of the REBCO-MI coil is 73.6 times greater than that of the IBS-MI coil, while the R ct of the REBCO-NI coil is 3.6 times greater than that of the IBS-NI coil. The main reasons for this difference will also be analyzed in this paper. From an application perspective, the low R ct of uninsulated coils also means high thermal stability and self-protection. This work lays the foundation for investigating the proportional and integral feedback control method to eliminate magnetic field delays and for validating the thermal stability of IBS uninsulated coils in future studies.

  • The Bending Performance Study of Bridge-Type Butt Joint of REBCO Tapes

    by Jingli Cao, Menglin Wang, Yatian Pei, Qingyuan Li, Ling Zhao, Qingjin Xu, Min Zhang, Hui Yang, Feipeng Ning

    To meet the magnetic field design requirements of a new detector for the Circular Electron Positron Collider (CEPC), a novel Aluminum-stabilized Stacked REBCO Tape Cable (ASTC) has been proposed and developed. Bridge-type butt joints are utilized to interconnect the rare-earth barium copper oxide (REBCO) tapes within the cable for the production of kilometer-scale cables. In this investigation, bridge-type butt joints of REBCO tape were fabricated using soldering techniques, and their bending performance under various bending diameters at 77 K and self-field conditions was examined through finite element analysis and bending tests. The simulation and experimental results showed a gradual degradation in the critical current (Ic) of the bridge-type butt joint under bending strain. Enhanced bending performance was achieved by positioning the joint gap at the lower side and increasing the gap between joints. When the gap distance is 10 mm, the critical bending radius threshold may lie between 25 mm and 20 mm. Finite element analysis revealed a notable degradation in Ic when the equivalent strain surpassed 0.4%, indicating uneven stress distribution during bending, leading to localized areas experiencing elevated stress levels that could result in potential damage and degradation.


  • Open Access

    Investigation of normal zone propagation velocity in AgSn/Ag/Ba122 superconducting tapes using a conduction cooling test system

    by Chunyan Li, Jin Zhou, Ling Zhao, Yanchang Zhu, Rui Kang, Wei Li, Chengtao Wang, Yingzhe Wang, Juan Wang, Zhilong Hou, et al.

    The investigation of the behavior of quench propagation in iron-based superconducting (IBS) tapes is important for their application in magnets and the design of quench protection systems. However, little research has been done in this area. In this work, a conduction cooling test system for IBS tapes and coils has been built, which has functions such as charging test, temperature and voltage data acquisition, pulse current heating, quench detection and protection. A series of experiments were performed on several 27 cm long IBS tapes to measure their normal zone propagation velocity (NZPV). The variation trends of NZPV with different operating temperatures, and with different ratios of operating current to critical current were systematically explored. In addition, monitoring all the voltages between different positions of an IBS tape, including two joints, has provided more detailed results and findings.


  • Study on Normal Bending Characteristics of Aluminium-Stabilized Stacked HTS Tape Cable for CEPC Detector Magnet

    by Yatian Pei, Jingli Cao, Menglin Wang, Zian Zhu, Ling Zhao, Zhongxiu Liu, Zhilong Hou, Huan Yang, Qingjin Xu, Feipeng Ning

    The Circular Electron Positron Collider (CEPC) is a significant international scientific facility proposed by the Chinese particle physics community in 2012, aimed at conducting detailed measurements of the properties of the Higgs boson. The latest conceptual design of the CEPC detector magnet introduced a novel Aluminum-stabilized Stacked HTS Tape Cable (ASTC). The minimum bending radius of the cable needs to be defined to provide a reference for the compact arrangement of current input and output positions. In this paper, a Finite Element Analysis (FEA) method is used to analyse the normal strain of different bending radii of ASTC. Experimental tests and calculation were conducted to verify the accuracy of the simulation results for critical current under different bending radii. The relationship between normal strain and critical current was obtained, showing that when the normal strain exceeds 0.004, a noticeable decrement occurs.


  • Toward an Encapsulated LTS Quench Detector for Fast Quench Detection in HTS Magnets

    by Rui Kang, Juan Wang, Qingjin Xu

    A fast and reliable quench detection method is one of the most urgent demands for the development of high temperature superconducting (HTS) magnets. Among the several new methods, using a co-wound low temperature superconductor (LTS) shows unique advantages over the others like optic fibers, acoustic signals, radio-frequency wave, stray-capacitance, or even fluorescent thermal imaging. First, an LTS quench detector after all measures voltage signals which is the same as present quench detection method. In addition, it is applicable to almost all kinds of magnets, regardless of the coil geometry or cooling method: the only need is to properly install the LTS wire. Here we propose an encapsulated Nb 3 Sn quench detector that is inspired by the quench heater. With numerical quench simulations, different arrangements of the Nb 3 Sn wires are studied for their detection efficiency. The thickness of the insulation between REBCO coil and Nb3Sn wire is also studied.


  • Conceptual Design Study of a Superconducting Flywheel System With Enhanced Speed Using Dipole Field

    by Rui Ma, Yaqiang Wang, Hongjun Zhang, Chengtao Wang, Jinrui Shi, Ze Feng, Wei Li, Xin Chen, Jin Zhou, Rui Kang, et al.

    The high temperature superconductivity (HTS) technology present itself a bright future to be used in a flywheel energy storage system (FESS). In addition to the characteristics of conventional flywheel energy storage systems, the self-stability of high temperature superconducting maglev enables the suspension bearing to completely eliminate external control, improving the efficiency and stability of the whole system. And superconducting flywheel energy storage system can effectively eliminate the loss caused by mechanical friction and the electrical loss caused by resistance. In this paper, a superconducting flywheel system which is suspended and self-stabilized through the meticulous design of a high magnetic field is presented. The most obvious advantages are the reduction of mechanical friction, the use of Lorentz force to provide centripetal force instead of relying on mechanical limit of materials, and a higher speed than traditional flywheels. The optimization of the field distribution as well as the HTS coil of the flywheel is discussed. Subsequently, the energy storage efficiency, power density, energy ratio and suspension force of the flywheel are analyzed and compared in detail.


  • Numerical Simulation of the Mechanical Behavior of a Transposed Cable With the In-Plane Bending of ReBCO Tapes

    by Yaqiang Wang, Rui Ma, Hongjun Zhang, Wei Li, Jinrui Shi, Ze Feng, Chengtao Wang, Juan Wang, Jin Zhou, Xin Chen, et al.

    The Institute of High Energy Physics, Chinese Academy of Sciences (IEHP, CAS) proposed a compact ReBCO cable (named X-cable) which is implemented by in-plane bending ReBCO tapes to realize the transposition, and successfully fabricated a 10 m length prototype cable. The study on the mechanical properties of the cable is of great significance to its engineering application. Based on the finite element model, the stress-strain state of cable under different loads has been analyzed, which are used to predict the critical current performance of superconducting tapes in cable. This paper focuses on the possible failure mechanism of the X-cable under bending and transverse loads. Based on the established model, the critical bending radius of the x-cable is determined to be 20 mm. We analyzed the critical pressure and shear stress of the cable under lateral load, considering two possible scenarios that may occur during the manufacturing process. The above results can serve as a valuable reference for subsequent design of magnets and winding of coils.


  • A Novel Aluminum-Stabilized Stacked REBCO Tape Cable

    by Menglin Wang, Feipeng Ning, Yatian Pei, Yaqiang Wang, Jingli Cao, Ling Zhao, Qingjin Xu, Zian Zhu

    In the new concept design of the circular electron positron collider detector, the magnet should be an ultrathin HTS solenoid with maximum radiation transparency. A novel aluminum-stabilized stacked REBCO tape cable (ASTC) was proposed and developed. The advantages of aluminum's high residual resistivity ratio, high thermal conductivity, and high transparency for particles, combined with the advantages of REBCO tape's high engineering current density, high strength and large temperature margin, constitute a suitable cable option for future detector magnets. The ASTC uses REBCO tapes in a stacked structure, which are wrapped and bound with metal tapes, and then covered with aluminum stabilizer by coextrusion processing. By optimizing the process parameters, such as preheating temperature, extrusion speed, Al outer layer thickness, and improving the internal structure of the cable, the critical current of the ASTC prototype cable is increased to 905 A@ 77 K, self-field. The degradation of the tape is less than 20%. This article presents the development process of the ASTC cable, discusses the challenges encountered during cable processing, and proposes corresponding solutions.