RPRoberto Caldas de Andrade Pinto

Roberto Caldas de Andrade Pinto

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Roberto Caldas de Andrade Pinto has a total of 54 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Diffuse Ultrasound on the Evaluation of Surface Crack Repair in Concrete Structures

    by Federal University of Santa Catarina (UFSC), Diana M. P. Caires, Roberto C. A. Pinto

    Concrete structures are prone to cracking due to material and external factors, requiring effective monitoring and quality control. In order to maintain the integrity of the surface, the injection of synthetic resins is usually applied. The effectiveness of a repair procedure can be performed nondestructively using ultrasound. This study investigates the applicability of the diffuse ultrasound technique in evaluating surface crack repairs in concrete structures. Concrete prisms with induced surface cracks were cast. The cracks were repaired in two stages using epoxy resin: an initial partial filling, followed by complete filling. The results demonstrate the potential of the technique in detecting the surface crack repair effectiveness, especially through the diffusivity parameter.

  • Shear behaviour of beams produced with ultra-high-performance concrete

    by Matheus Agustini, Victória Gonçalves Dias, Kaio César de Oliveira, Ana Júlia Zunta Carniel, Roberto Caldas de Andrade Pinto

    Ultra-high-performance concrete (UHPC) and ultra-high-performance fibre-reinforced concrete (UHPFRC) have emerged as useful materials to improve mechanical properties, ductility and durability of concrete structures. Although there have been significant advances in developments at the material level, standardised design methods for UHPC and UHPFRC structures that represent their mechanical behaviour are still to be incorporated in international codes. Traditional design methods may not be applied to UHPC and UHPFRC elements. Experimental data analysing the shear behaviour of UHPC beams with and without transverse reinforcement and UHPFRC beams without transverse reinforcement are presented in this paper. The cracking patterns, cracking loads, ultimate load capacities and stiffness behaviour were evaluated and compared with theoretical estimates. The results showed that transverse reinforcement and steel fibre reinforcement increased the load-carrying capacity of the beam. The presence of transverse reinforcement did not influence the stiffness of the beams, whereas the steel fibres made the UHPFRC beams significantly stiffer. While the transverse reinforcement only restricted the opening of shear cracks, the addition of steel fibres also prevented the propagation of these cracks, resulting in multiple independent cracks in the UHPFRC beams. The theoretical estimates only provided a good prediction of the experimental results for beams with transverse reinforcement.


  • Open Access

    Reliability analysis of strut-and-tie models for the design of deep beams according to NBR 6118 (2023)

    by Paulo Henrique Staciarini, Roberto Caldas de Andrade Pinto, Wellison José de Santana Gomes

    The strut-and-tie method (STM) applied in the structural design of deep beams is a semi-probabilistic method, that does not take directly into account both the uncertainties associated with the variables involved and those inherent in the calculation models. However, with the use of structural reliability methods, it is possible to consider such uncertainties. Reliability analysis allows the verification and the comparison of the safety level between different structural design solutions. Although there are studies in the literature that present structural reliability analyses involving the STM, there is still a lack in what concerns applications of this method in structural design following the Brazilian standards. This paper presents reliability analyses of two strut-and-tie models for deep beams, designed according to the Brazilian standard NBR 6118 (2023). The models differ in the inclusion of vertical reinforcement. The resistance model error was incorporated in the limit-state equation from deep beam tests obtained from the literature. Monte Carlo simulation was used to obtain the reliability index, making it possible to identify the most significant failure modes. The results indicated reliability index β greater than 3.5 for both models, which are in accordance with target values indicated in the literature. The strut-and-tie model with vertical reinforcement presented a higher reliability index and also a greater probability of presenting ductile failure. The reliability analyses also indicated a great influence of the live load to total load (dead and live) ratio on the reliability index. In the structural design, higher safety was achieved using the load factors of NBR 8681 (2003) for type 1 buildings ( g=1.35 and q=1.5) rather than the common load factors for type 2 buildings ( g=1.4 and q=1.4) given by NBR 6118 (2023).

  • Open Access

    Ultrasound monitoring of setting behavior of concrete mixtures

    by Hella Fernanda Giehl Bressan, Felipe Carraro, Roberto Caldas de Andrade Pinto

    The setting behavior of concrete mixtures can be indirectly monitored by the penetration resistance test given by ASTM C 403. Arbitrary values of penetration resistance are associated to the initial and final set times. This test is carried out on the previously sieved mortar portion of the concrete mixture, which makes its practical use rare. Alternatively, ultrasound testing can be used to characterize this transition period, since the propagation of ultrasonic waves is greatly affected by the formation of cement hydration products and the extent of microstructure development. In this research, the propagation of ultrasonic waves in fresh concrete during the setting period was studied. In addition to the ultrasonic pulse velocity (UPV), other ultrasonic parameters such as group velocity, parameters related to ultrasonic energy and frequency were monitored during the setting period of various concrete mixes. It was observed that as setting progressed, there was a greater ease of ultrasonic transmission with a continuous increase of wave amplitudes. The results indicated that a combined analysis of the time domain parameters of UPV, group velocity and the time that 10% of energy has propagated (t10) could be used to improve the characterization of the microstructure development regarding the setting behavior of concrete mixtures.

  • Evaluation of self-consolidating concrete shear strength by means of push-off test

    by Brunela Francine da Cunha, Roberto Caldas de Andrade Pinto, Gustavo Savaris

    Self-consolidating concrete (SCC) can be characterised by its flowability, stability and passing ability. Although SCC tends to have a more uniform microstructure in the concrete–reinforcement interfacial transition zone, the reduction of the nominal size and coarse aggregate content in the concrete mix may adversely affect its shear strength. Therefore, the aim of this research was to evaluate the shear strength of SCC by means of push-off tests of 45 specimens, produced with one conventional concrete and two SCC mixtures, with two different coarse aggregate contents (reference and reduced by 30%). The transverse reinforcement ratio ranged from 0.46% to 2.28%, using closed stirrups crossing the shear plane. The increase of reinforcement ratio resulted in improvements in shear strength for specimens with one, two and three stirrups, while specimens with four and five stirrups had a premature failure owing to concrete crushing near the notch. No significant difference in shear strength was identified owing to concrete type or coarse aggregate. The experimental results were also compared with codes estimates, and Eurocode 2 presented the best fit to experimental results when compared with the American code ACI 318 and the Canadian standard CSA A23.3.


  • Open Access

    Shear friction capacity of self-consolidating concrete

    by Gustavo Savaris, Roberto Caldas de Andrade Pinto

    An experimental research was developed to evaluate shear transfer in self-consolidating. Three concrete mixes were prepared, one conventional and two self-consolidating, differing on the proportion of the coarse and fine aggregate used. Nine push-off specimens, containing steel reinforcement passing through the shear plane, were tested, to evaluate the ultimate shear stress and shear plane displacements. Shear strength of self-consolidating concrete specimens were higher than conventionally vibrated concrete. The experimental results were compared to the shear strength estimated by literature and code based equations, yielding conservative results of these equations for both types of concrete, especially the models that disregard the compressive strength of concretes.


  • Open Access

    Ultrasonic investigation on the effectiveness of crack repair in concrete

    by Fabio Caon de Souza, Roberto Caldas de Andrade Pinto

    The crack injection technique using epoxy systems is usually performed in the services of rehabilitation of surface cracks in concrete structures. The evaluation of the injection process can be done by the removal of cores, which is a destructive test not able to evaluate the entire structure. Alternatively, the use of nondestructive testing, specifically those based on the propagation of stress waves can provide information on the effectiveness of injection services. Even though the time-of-flight technique which provides the ultrasonic pulse velocity is the most common parameter used in concrete evaluation, the ultrasound waveform energy-related parameters can be used to indicate if crack was fully filled. The energy of the ultrasound signal depends on the propagated travel path, which differs when the crack is not filled. This paper presents the results of an experimental program with artificial surface cracks filled with epoxy in different depth fractions. Two types of epoxy were used. It was observed that the ultrasound waveform energy-parameters were able to detect repair effectiveness.


  • Open Access

    Influence of different sources of coal gangue used as aluminosilicate powder on the mechanical properties and microstructure of alkali-activated cement

    by B. J. Frasson, R. C.A. Pinto, J. C. Rocha

    Coal mining wastes are associated with serious environmental problems; they have potential as building materials, including alkali-activated cement. In this study, the effect of different coal mining wastes on the mechanical properties and microstructural development of alkali-activated materials (AAMs) was evaluated through XRD, SEM and FTIR spectroscopy. Different alkali-activated compounds were produced; the alkaline solution was composed of NaOH+Na2SiO3. The results obtained using the calcined coal sludge showed excellent mechanical performance, with compressive strength higher than 60 MPa. However, addition of metakaolin and ordinary Portland cement was necessary to increase the mechanical performance of calcined coal gangue materials. The formation of N-A-S-H gel and the incorporation of iron ions into the cementitious matrix were evidenced. Ultrasonic pulse velocity indicated the early polymerization during the reaction processes. The study verified that the different characteristics of the wastes influence the performance of alkali-activated materials.


  • Open Access

    Experimental investigation on shear resistance of self-consolidating concrete beams

    by G. Savaris, R. C. A. Pinto

    Self-consolidating concrete stands out for its high fluidity and stability, which are obtained by the reduction of the coarse aggregate dimensions and content in the mixture and also by the addition of superplasticizer and viscosity modifiers. An experimental test program was carried out to evaluate the influence of these particularities of self-consolidating concrete mixtures on the shear capacity of beams with shear reinforcement. Four mixtures of self-compacting concrete and two mixtures of conventionally vibrated concrete with different coarse aggregate size and volume were used for the production of beams to be tested under flexure. The experimental results were compared to those estimated by the ACI-318, CAN A23.3, EC-2 and NBR 6118 design codes. The results demonstrated that the reduction of coarse aggregate dimensions and content in self-compacting concrete mixture did not significantly influence the ultimate shear strength. The shear strengths obtained experimentally were considered adequate to codes estimates, for both concrete types.