Chung-De Chen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Chung-De Chen has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
Po-Hao Wang
Department of Structural Analysis, Aerospace Industrial Development Corporation, No.1, Hanxiang Road, Xitun District, Taichung City, Taichung, 407803, TAIWAN
3 shared publicationsBing-Feng Huang
National Cheng Kung University
2 shared publications- Po-Wen Su
Department of Mechanical Engineering, National Cheng Kung University, Tainan, Taiwan
2 shared publications Rong-Der Chien
Engineer, Dept. of Structural Analysis, Aerospace Industrial Development Corporation, No.1, Hanxiang Rd., Xitun District, Taichung City 40760, Taiwan
2 shared publicationsYao-Hung Huang
Engineer, Dept. of Structural Analysis, Aerospace Industrial Development Corporation, No.1, Hanxiang Rd., Xitun District, Taichung City 40760, Taiwan
2 shared publicationsYu-Hsien Chen
2 shared publications
Latest Publications
- 17 December 2025
- Published by ASME International in Journal of Computational and Nonlinear Dynamics
- Vol. 21 (4)
Centrifugal Disk Magnetically Plucking Piezoelectric Beam for Broadband Energy Harvesting in Low-Speed Environments
In this paper, a broadband piezoelectric energy harvester based on an eccentric disk with frequency self-tuning for magnetic plucking in low-speed rotating environments is presented. The eccentric disk swings a large swing angle and magnetically plucks the piezoelectric beam. The plucking causes a transient vibration and generates power due to the piezoelectric effect. The mathematical model (equations of motion) for eccentric disk and piezoelectric beam is derived and solved numerically. The nonlinear dynamic analysis reveals that the eccentric disk exhibits frequency self-tuning, i.e., the frequency self-tuning disk is always in resonance within some rotational velocity range. This capability further magnifies the power output and broadens the bandwidth of the piezoelectric energy harvesting (PEH). The prototype of PEH as well as the experimental setup is developed for measurements. The numerical solutions agree well with the experimental data, showing that the validity of the model has been ensured. The proposed PEH can generate a power greater than 0.1 mW with a bandwidth ranging from 100 rpm (1.67 Hz) to 200 rpm (3.33 Hz).
- 17 December 2025
- Published by ASME International in Journal of Computational and Nonlinear Dynamics
- Vol. 21 (4)
Centrifugal Disk Magnetically Plucking Piezoelectric Beam for Broadband Energy Harvesting in Low-Speed Environments
In this paper, a broadband piezoelectric energy harvester based on an eccentric disk with frequency self-tuning for magnetic plucking in low-speed rotating environments is presented. The eccentric disk swings a large swing angle and magnetically plucks the piezoelectric beam. The plucking causes a transient vibration and generates power due to the piezoelectric effect. The mathematical model (equations of motion) for eccentric disk and piezoelectric beam is derived and solved numerically. The nonlinear dynamic analysis reveals that the eccentric disk exhibits frequency self-tuning, i.e., the frequency self-tuning disk is always in resonance within some rotational velocity range. This capability further magnifies the power output and broadens the bandwidth of the piezoelectric energy harvesting (PEH). The prototype of PEH as well as the experimental setup is developed for measurements. The numerical solutions agree well with the experimental data, showing that the validity of the model has been ensured. The proposed PEH can generate a power greater than 0.1 mW with a bandwidth ranging from 100 rpm (1.67 Hz) to 200 rpm (3.33 Hz).
- 20 August 2025
- Published by Taylor & Francis in Journal of the Chinese Institute of Engineers
- Vol. 49 (1) , 64-78
Vibration analysis in sandwich composite beams based on higher order zigzag theory
- 20 August 2025
- Published by Taylor & Francis in Journal of the Chinese Institute of Engineers
- Vol. 49 (1) , 64-78
Vibration analysis in sandwich composite beams based on higher order zigzag theory
- 23 August 2024
- Published by Springer Nature
- p. 293-301
Development of the C0-Continuous Finite Element Models for Sandwich Beams Based on Higher-Order Refined Zigzag Theory
- 23 August 2024
- Published by Springer Nature
- p. 293-301
Development of the C0-Continuous Finite Element Models for Sandwich Beams Based on Higher-Order Refined Zigzag Theory
- Open Access
- 22 August 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (16) , 7424
Anatomical-Based Customized Cervical Orthosis Design in Automation
Cervical orthoses, vital for neck immobilization in medical care and sports, often struggle to provide adequate support due to individual neck shape and size variations. This study addresses this issue by developing a specific computer-aided orthosis design software tailored for creating customized 3D-printed cervical orthoses. The self-developed software embedded anatomical and rehabilitation knowledge into the orthosis design process, ensuring consistency and reducing manual modification. Finite element analysis of cervical orthoses determined that a minimum thickness of 5 mm PLA (polylactic acid) material is necessary to meet safety requirements. This study highlights the automation potential of customized computer-aided orthosis design and underscores the potential to revolutionize orthopedic care. We also applied easy-to-access 3D printing technology to fabricate well-fitting and immobilized cervical orthoses. These customized cervical orthoses offer a promising future with the advantages of being cost-effective, lightweight, immobility, comfortable, easy to wear, and minimal accessories to meet clinical needs, enhancing patient comfort and compliance and providing reassurance about the economic benefits of the technology.
- 22 August 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (16) , 7424
Open AccessAnatomical-Based Customized Cervical Orthosis Design in Automation
Cervical orthoses, vital for neck immobilization in medical care and sports, often struggle to provide adequate support due to individual neck shape and size variations. This study addresses this issue by developing a specific computer-aided orthosis design software tailored for creating customized 3D-printed cervical orthoses. The self-developed software embedded anatomical and rehabilitation knowledge into the orthosis design process, ensuring consistency and reducing manual modification. Finite element analysis of cervical orthoses determined that a minimum thickness of 5 mm PLA (polylactic acid) material is necessary to meet safety requirements. This study highlights the automation potential of customized computer-aided orthosis design and underscores the potential to revolutionize orthopedic care. We also applied easy-to-access 3D printing technology to fabricate well-fitting and immobilized cervical orthoses. These customized cervical orthoses offer a promising future with the advantages of being cost-effective, lightweight, immobility, comfortable, easy to wear, and minimal accessories to meet clinical needs, enhancing patient comfort and compliance and providing reassurance about the economic benefits of the technology.
- Open Access
- 20 March 2024
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 33 (4) , 045028
A Lamb-wave based SHM for multi-damage localizations in large composite plates by using piezoelectric transducer array
In this paper, a Lamb-wave based structural health monitoring for multi-damage localizations in large composite plates is presented. The Lamb waves are generated and received by piezoelectric transducers, which are arranged in array on the composite plate. In the experiments, three composite plates with various laminate stacking sequences and taper designs were prepared. The damages were created on the specimens by impact testing. In each specimen, 24 piezoelectric transducers were utilized and mounted on the specimen surface. This study proposed an algorithm to identify the damage localizations. The transducer layout is classified by 10 subsets. In each subset, the wave propagation paths can be grouped into path groups pivoted by actuators and that by sensors. Based on the damage index, the mean angle line for each path group in a subset can be obtained. By assuming that the mean angle line passes through the actual damage, the damage localization can be achieved if there exist more than two mean angle lines in one subset. In this study, two exclusion rules are proposed to exclude a path group from the damage localization calculations. The damage localization results show that, for a composite plate with multiple damages, their locations can be identified by using multiple subsets. The damage localization results show that the damage location can be accurately predicted for the case that a damage exists in the interior of a subset. The experiment results also show that the Lamb wave characteristics and the localization results are not affected by the thickness variation of the plate, indicating that the proposed algorithm is available for tapered composite plate.
- 20 March 2024
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 33 (4) , 045028
Open AccessA Lamb-wave based SHM for multi-damage localizations in large composite plates by using piezoelectric transducer array
In this paper, a Lamb-wave based structural health monitoring for multi-damage localizations in large composite plates is presented. The Lamb waves are generated and received by piezoelectric transducers, which are arranged in array on the composite plate. In the experiments, three composite plates with various laminate stacking sequences and taper designs were prepared. The damages were created on the specimens by impact testing. In each specimen, 24 piezoelectric transducers were utilized and mounted on the specimen surface. This study proposed an algorithm to identify the damage localizations. The transducer layout is classified by 10 subsets. In each subset, the wave propagation paths can be grouped into path groups pivoted by actuators and that by sensors. Based on the damage index, the mean angle line for each path group in a subset can be obtained. By assuming that the mean angle line passes through the actual damage, the damage localization can be achieved if there exist more than two mean angle lines in one subset. In this study, two exclusion rules are proposed to exclude a path group from the damage localization calculations. The damage localization results show that, for a composite plate with multiple damages, their locations can be identified by using multiple subsets. The damage localization results show that the damage location can be accurately predicted for the case that a damage exists in the interior of a subset. The experiment results also show that the Lamb wave characteristics and the localization results are not affected by the thickness variation of the plate, indicating that the proposed algorithm is available for tapered composite plate.
- 23 September 2023
- Published by World Scientific Pub Co Pte Ltd in International Journal of Structural Stability and Dynamics
- Vol. 24 (11)
An Accurate Solution for Buckling and Nonlinear Analysis of a Sandwich Beam with Functionally Graded Material by Considering Zigzag Displacements
In this paper, critical buckling analysis and nonlinear load-deflection curve for sandwich beam with functionally graded material are presented based on refined zigzag theory (RZT). By using the variational principle, the equilibrium equations in buckling analysis are given based on the RZT formulations as well as the nonlinear strain-displacement relations. The solutions are also derived for eigenvalue problems in critical buckling load calculations and for load-deflection relations with initial geometric imperfection. The solutions are presented analytically, and the mathematical properties during the derivation process have been proven in order to keep the mathematical rigor. The present analytical RZT critical buckling loads are validated by the RZT FEM, which is the finite element solutions of the sandwich beam meshed by the beam elements based on RZT. These solutions are also compared by commercial software ANSYS, resulting that this approach can obtain an accurate critical buckling load. Various parameters such as aspect ratio, thickness ratio and modulus ratio are considered to investigate their effects on the critical buckling loads. The present results are compared to the beams with higher-order shear deformation theory (HSDT). From the comparisons of the RZT and the HSDT results, it is seen that both theories approach to CBT for slender beam. The results show that the HSDT overestimates the stiffness in the load-deflection curve. It is shown that the RZT exhibits the zigzag displacements at high accuracy, resulting in accurate calculation in critical buckling loads, mode shapes and nonlinear load-deflection curves than HSDT. The superiority of the RZT solutions is presented especially for the case of FGM sandwich beam with soft middle layer.
- 23 September 2023
- Published by World Scientific Pub Co Pte Ltd in International Journal of Structural Stability and Dynamics
- Vol. 24 (11)
An Accurate Solution for Buckling and Nonlinear Analysis of a Sandwich Beam with Functionally Graded Material by Considering Zigzag Displacements
In this paper, critical buckling analysis and nonlinear load-deflection curve for sandwich beam with functionally graded material are presented based on refined zigzag theory (RZT). By using the variational principle, the equilibrium equations in buckling analysis are given based on the RZT formulations as well as the nonlinear strain-displacement relations. The solutions are also derived for eigenvalue problems in critical buckling load calculations and for load-deflection relations with initial geometric imperfection. The solutions are presented analytically, and the mathematical properties during the derivation process have been proven in order to keep the mathematical rigor. The present analytical RZT critical buckling loads are validated by the RZT FEM, which is the finite element solutions of the sandwich beam meshed by the beam elements based on RZT. These solutions are also compared by commercial software ANSYS, resulting that this approach can obtain an accurate critical buckling load. Various parameters such as aspect ratio, thickness ratio and modulus ratio are considered to investigate their effects on the critical buckling loads. The present results are compared to the beams with higher-order shear deformation theory (HSDT). From the comparisons of the RZT and the HSDT results, it is seen that both theories approach to CBT for slender beam. The results show that the HSDT overestimates the stiffness in the load-deflection curve. It is shown that the RZT exhibits the zigzag displacements at high accuracy, resulting in accurate calculation in critical buckling loads, mode shapes and nonlinear load-deflection curves than HSDT. The superiority of the RZT solutions is presented especially for the case of FGM sandwich beam with soft middle layer.
- 12 March 2023
- Published by Elsevier in Applied Mathematical Modelling
- Vol. 119, 586-604
A novel higher-order refined zigzag theory for static bending analysis in sandwich composite beam
- 12 March 2023
- Published by Elsevier in Applied Mathematical Modelling
- Vol. 119, 586-604
A novel higher-order refined zigzag theory for static bending analysis in sandwich composite beam
- 1 November 2022
- Published by American Society of Civil Engineers (ASCE) in Journal of Aerospace Engineering
- Vol. 35 (6) , 04022101
Lamb Wave–Based Structural Health Monitoring for Aluminum Bolted Joints with Multiple-Site Fatigue Damage
In this paper, the Lamb wave based structural health monitoring for aluminum bolted joints with multiple-site fatigue damages was investigated experimentally. In the experiments, the Lamb waves were generated and received by piezoelectric transducers. Three specimens were prepared for fatigue testing and monitored by the Lamb wave signals. Due to the complex geometry of the specimen, multiple fatigue cracks were observed at different bolt holes during the fatigue testing. The signals before and after the initiation of the fatigue cracks were compared to calculate the damage index (DI). In general cases, DI can serve an indicator to map the fatigue crack size. In the experiments, it was found that the phase shifts between the baseline signal before fatigue crack initiates, , and the signal with fatigue cracks, , can result in an overestimated DI. To solve this problem, the envelope damage index (EDI) was introduced to monitor the fatigue cracks. The envelope curves of and are considered in the calculation of EDI. In the experiments, three specimens were prepared for fatigue testing. Crack-size observations of the specimens indicated that the EDI is a better parameter than DI for monitoring the fatigue crack size and location.- 1 November 2022
- Published by American Society of Civil Engineers (ASCE) in Journal of Aerospace Engineering
- Vol. 35 (6) , 04022101
Lamb Wave–Based Structural Health Monitoring for Aluminum Bolted Joints with Multiple-Site Fatigue Damage
In this paper, the Lamb wave based structural health monitoring for aluminum bolted joints with multiple-site fatigue damages was investigated experimentally. In the experiments, the Lamb waves were generated and received by piezoelectric transducers. Three specimens were prepared for fatigue testing and monitored by the Lamb wave signals. Due to the complex geometry of the specimen, multiple fatigue cracks were observed at different bolt holes during the fatigue testing. The signals before and after the initiation of the fatigue cracks were compared to calculate the damage index (DI). In general cases, DI can serve an indicator to map the fatigue crack size. In the experiments, it was found that the phase shifts between the baseline signal before fatigue crack initiates, , and the signal with fatigue cracks, , can result in an overestimated DI. To solve this problem, the envelope damage index (EDI) was introduced to monitor the fatigue cracks. The envelope curves of and are considered in the calculation of EDI. In the experiments, three specimens were prepared for fatigue testing. Crack-size observations of the specimens indicated that the EDI is a better parameter than DI for monitoring the fatigue crack size and location.- 11 October 2021
- Published by Springer Nature in Acta Mechanica
- Vol. 232 (11) , 4645-4668
An analytical solution for vibration in a functionally graded sandwich beam by using the refined zigzag theory
- 11 October 2021
- Published by Springer Nature in Acta Mechanica
- Vol. 232 (11) , 4645-4668
An analytical solution for vibration in a functionally graded sandwich beam by using the refined zigzag theory