Akihiro Hamanaka
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Akihiro Hamanaka has a total of 125 co-authors. Here are the top co-authors by number of shared publications:
- Hideki Shimada
Department of Earth Resources Engineering, Kyushu University, Fukuoka 819-0395, Japan
30 shared publications - Takashi Sasaoka
Department of Earth Resources Engineering, Kyushu University, Fukuoka 819-0395, Japan
29 shared publications Takashi Sasaoka
23 shared publicationsHideki Shimada
22 shared publicationsFa-Qiang Su
7 shared publicationsGota Deguchi
7 shared publications
Latest Publications
- Open Access
Stability of the Upper Gateroad and Chain Pillar in Steeply Inclined Longwall Mining: A South Gobi Case Study
Mongolia is preparing several major South Gobi coal operations, including the Narynsukhait (NS) coal mine, for the transition from open-pit to underground mining. In steeply dipping longwall mining, the upper gateroad is particularly critical because it lies adjacent to the gob and bears the side abutment stress during panel retreat. This study uses three-dimensional finite-difference modeling (FLAC3D) at the NS site to identify the factors that compromise upper gateroad stability and to examine controllable design countermeasures. Since no monitoring data exist yet, the computed displacements serve as response indices for comparing cases. Across parametric ranges of seam dip (30–60°), mining depth (300–700 m), lateral stress ratio (0.5–2.0), and rock mass deterioration (down to GSI = 20), rock mass quality emerges as the dominant factor, while seam dip has a smaller influence, expressed mainly through the chain pillar rather than the gateroad itself. A gateroad parallel to the major horizontal stress experiences markedly less damage than one intersected at 90°, although this difference narrows as the seam steepens. Under the intersecting configuration, the chain pillar fails at 700 m depth. Because gateroad orientation can be chosen at no cost to coal recovery, the findings support combining rock mass characterization and in-situ stress measurement with orientation control and adequate chain pillar width.
Open AccessStability of the Upper Gateroad and Chain Pillar in Steeply Inclined Longwall Mining: A South Gobi Case Study
Mongolia is preparing several major South Gobi coal operations, including the Narynsukhait (NS) coal mine, for the transition from open-pit to underground mining. In steeply dipping longwall mining, the upper gateroad is particularly critical because it lies adjacent to the gob and bears the side abutment stress during panel retreat. This study uses three-dimensional finite-difference modeling (FLAC3D) at the NS site to identify the factors that compromise upper gateroad stability and to examine controllable design countermeasures. Since no monitoring data exist yet, the computed displacements serve as response indices for comparing cases. Across parametric ranges of seam dip (30–60°), mining depth (300–700 m), lateral stress ratio (0.5–2.0), and rock mass deterioration (down to GSI = 20), rock mass quality emerges as the dominant factor, while seam dip has a smaller influence, expressed mainly through the chain pillar rather than the gateroad itself. A gateroad parallel to the major horizontal stress experiences markedly less damage than one intersected at 90°, although this difference narrows as the seam steepens. Under the intersecting configuration, the chain pillar fails at 700 m depth. Because gateroad orientation can be chosen at no cost to coal recovery, the findings support combining rock mass characterization and in-situ stress measurement with orientation control and adequate chain pillar width.
- Open Access
- 1 September 2026
- Published by Elsevier in Journal of Rock Mechanics and Geotechnical Engineering
Rheology-dependent damage evolution and mechanical behavior of slurry-infiltrated granular materials
- 1 September 2026
- Published by Elsevier in Journal of Rock Mechanics and Geotechnical Engineering
Open AccessRheology-dependent damage evolution and mechanical behavior of slurry-infiltrated granular materials
- Open Access
- 30 June 2026
- Published by National Research and Innovation Agency in RISET Geologi dan Pertambangan
- Vol. 36 (1) , 135
Numerical characterization of tapering features in non-uniform weak interlayers for proposed slope stability geometry
Folding and subsequent pinching out are common geological features in geologically active areas. This gives layers a non-uniform thickness, especially for a multilayer slope with a weak interlayer. Thickness non-uniformity is often disregarded in stability analysis to simplify slope models. However, the geometrical variability of rock masses always exists, and the impact is inevitable; therefore, it is not to be discounted. This research systematically established a geometric correlation framework to understand how tapering configurations in weak interlayer influence slope stability in layered rock masses. Analytical and numerical methods are implemented using the RocScience code. Statistical analysis was also performed to assess the significance and correlation of tapering configurations to slope stability conditions. It was found out that Tilting Intensity (ρ≥0.736) and Thickness Gradient (ρ≥0.743) consistently exhibited the strongest (α=0) negative correlation with critical strength reduction factors and slip surface radius, confirming that taper steepness and vertical irregularity are the dominant geometrical destabilizers in non-uniform weak layers. Moreover, stratigraphic unevenness not only exerts a direct destabilizing influence but also modulates the sensitivity of other geometrical parameters, such as the aspect ratio, by a factor of 2 units ΔFS recorded at the highest elevation. The findings of this study carry several practical and scientific implications for slope design, geomechanical modeling, and geological interpretation in complex stratified rock masses.
- 30 June 2026
- Published by National Research and Innovation Agency in RISET Geologi dan Pertambangan
- Vol. 36 (1) , 135
Open AccessNumerical characterization of tapering features in non-uniform weak interlayers for proposed slope stability geometry
Folding and subsequent pinching out are common geological features in geologically active areas. This gives layers a non-uniform thickness, especially for a multilayer slope with a weak interlayer. Thickness non-uniformity is often disregarded in stability analysis to simplify slope models. However, the geometrical variability of rock masses always exists, and the impact is inevitable; therefore, it is not to be discounted. This research systematically established a geometric correlation framework to understand how tapering configurations in weak interlayer influence slope stability in layered rock masses. Analytical and numerical methods are implemented using the RocScience code. Statistical analysis was also performed to assess the significance and correlation of tapering configurations to slope stability conditions. It was found out that Tilting Intensity (ρ≥0.736) and Thickness Gradient (ρ≥0.743) consistently exhibited the strongest (α=0) negative correlation with critical strength reduction factors and slip surface radius, confirming that taper steepness and vertical irregularity are the dominant geometrical destabilizers in non-uniform weak layers. Moreover, stratigraphic unevenness not only exerts a direct destabilizing influence but also modulates the sensitivity of other geometrical parameters, such as the aspect ratio, by a factor of 2 units ΔFS recorded at the highest elevation. The findings of this study carry several practical and scientific implications for slope design, geomechanical modeling, and geological interpretation in complex stratified rock masses.
- Open Access
Assessing Stope Stability in Steep Thin-Vein Mine at Deep Depths: A Hybrid Empirical-Numerical Approach Considering Caved Rock Behavior
While conventional numerical studies often treat excavated stopes as empty voids or as backfilled, few investigations have simulated the post-mining void as a weak granular caved rock material that evolves naturally from a hanging wall failure. This study addresses this gap by modeling the caved rock progressively, which makes the excavation representation more realistic for sublevel caving operations. This study introduces stope stability for the Zarmitan gold mine in Uzbekistan, where mining occurs at about a 500 m depth in a narrow quartz vein. A hybrid approach combining empirical and numerical methods was adopted. The Mathews stability graph method provided initial design guidance, while three-dimensional FLAC3D numerical modeling was used to simulate the mining sequence with explicit representation of caved rock behavior. A various study was conducted, which included the effects of stress ratio, stope length along strike, and pillar thickness on overall stability. The obtained results show that the stress ratio is the dominant factor controlling stope behavior. Stope length significantly affects failure extent, with shorter stopes showing better performance under similar conditions. Pillar thickness was found to improve stability and reduce tensile stresses in critical areas, though in all cases, hanging wall support remains essential. The numerical results confirm empirical predictions while providing quantitative insights into stress distributions and failure mechanisms not captured by empirical methods alone. These results provide mine operators with quantitative, site-specific design criteria, most notably that, under the measured high horizontal stress, limiting stope length to 40 m and increasing pillar thickness to 8 m substantially improves hanging wall stability, which demonstrates how a hybrid empirical-numerical methodology can directly support safer and more economic extraction in deep, narrow-vein operations.
Open AccessAssessing Stope Stability in Steep Thin-Vein Mine at Deep Depths: A Hybrid Empirical-Numerical Approach Considering Caved Rock Behavior
While conventional numerical studies often treat excavated stopes as empty voids or as backfilled, few investigations have simulated the post-mining void as a weak granular caved rock material that evolves naturally from a hanging wall failure. This study addresses this gap by modeling the caved rock progressively, which makes the excavation representation more realistic for sublevel caving operations. This study introduces stope stability for the Zarmitan gold mine in Uzbekistan, where mining occurs at about a 500 m depth in a narrow quartz vein. A hybrid approach combining empirical and numerical methods was adopted. The Mathews stability graph method provided initial design guidance, while three-dimensional FLAC3D numerical modeling was used to simulate the mining sequence with explicit representation of caved rock behavior. A various study was conducted, which included the effects of stress ratio, stope length along strike, and pillar thickness on overall stability. The obtained results show that the stress ratio is the dominant factor controlling stope behavior. Stope length significantly affects failure extent, with shorter stopes showing better performance under similar conditions. Pillar thickness was found to improve stability and reduce tensile stresses in critical areas, though in all cases, hanging wall support remains essential. The numerical results confirm empirical predictions while providing quantitative insights into stress distributions and failure mechanisms not captured by empirical methods alone. These results provide mine operators with quantitative, site-specific design criteria, most notably that, under the measured high horizontal stress, limiting stope length to 40 m and increasing pillar thickness to 8 m substantially improves hanging wall stability, which demonstrates how a hybrid empirical-numerical methodology can directly support safer and more economic extraction in deep, narrow-vein operations.
- Open Access
- 18 May 2026
- Published by Elsevier in International Journal of Mining Science and Technology
- Vol. 36 (7) , 1433-1451
Developing low-carbon mine backfill: Performance optimization and carbon storage using CO2 nanobubble and high-volume fly ash
- 18 May 2026
- Published by Elsevier in International Journal of Mining Science and Technology
- Vol. 36 (7) , 1433-1451
Open AccessDeveloping low-carbon mine backfill: Performance optimization and carbon storage using CO2 nanobubble and high-volume fly ash
- Open Access
- 4 February 2026
- Published by Elsevier in SSRN Electronic Journal
Monitoring and analysis of produced-gas composition and gasification cavity development during underground coal gasification
This study developed a novel underground coal gasification (UCG) experimental system, conducting two sets of experiments to compare the effects of varying oxygen flow rate on produced-gas composition and gasification cavity development. Real-time analysis of gas composition was conducted using gas chromatography, and an energy recovery efficiency evaluation method was proposed to describe gasification performance. Based on elemental conservation during gasification, coal consumption was inferred from the gas composition and used to further estimate the gasification cavity volume, enabling process-based monitoring of gasification cavity development. Integrated temperature sensors and acoustic emission (AE) monitoring were used to monitoring the evolution and expansion of the gasification cavity. To address velocity variations caused by anisotropy in coal-rock media under high-temperature and high-pressure conditions, an elliptical-velocity model (EVM) was proposed, with experimental validation showing an average localization error of approximately 0.5%. Building on this, the AE-based 3D gasification cavity model was combined with Monte Carlo simulation to estimate the volume of the complex cavity, with volume errors controlled within 4%. Finally, a comparative analysis was conducted between the real gasification cavity volume, the volume estimated from produced-gas composition, and the volume estimated by Monte Carlo simulation, verifying the feasibility of both methods and exploring the impact of varying oxygen flow rates.
- 4 February 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessMonitoring and analysis of produced-gas composition and gasification cavity development during underground coal gasification
This study developed a novel underground coal gasification (UCG) experimental system, conducting two sets of experiments to compare the effects of varying oxygen flow rate on produced-gas composition and gasification cavity development. Real-time analysis of gas composition was conducted using gas chromatography, and an energy recovery efficiency evaluation method was proposed to describe gasification performance. Based on elemental conservation during gasification, coal consumption was inferred from the gas composition and used to further estimate the gasification cavity volume, enabling process-based monitoring of gasification cavity development. Integrated temperature sensors and acoustic emission (AE) monitoring were used to monitoring the evolution and expansion of the gasification cavity. To address velocity variations caused by anisotropy in coal-rock media under high-temperature and high-pressure conditions, an elliptical-velocity model (EVM) was proposed, with experimental validation showing an average localization error of approximately 0.5%. Building on this, the AE-based 3D gasification cavity model was combined with Monte Carlo simulation to estimate the volume of the complex cavity, with volume errors controlled within 4%. Finally, a comparative analysis was conducted between the real gasification cavity volume, the volume estimated from produced-gas composition, and the volume estimated by Monte Carlo simulation, verifying the feasibility of both methods and exploring the impact of varying oxygen flow rates.
- Open Access
- 2 February 2026
- Published by MDPI AG in Algorithms
- Vol. 19 (2) , 120
Probabilistic Prediction of Oversized Rock Fragments in Bench Blasting Using Gaussian Process Regression: A Comparative Study with Empirical and Multivariate Regression Analysis Models
Oversized rock fragments (boulders) produced during bench blasting adversely affect the efficiency of mining downstream processes such as loading, hauling, and crushing, thus leading to regularly requiring costly secondary breakage and the use of mechanized rock breakers. This study presents a probabilistic framework for forecasting boulder size in surface mining operations by employing Gaussian Process Regression (GPR), benchmarked against the Kuznetsov–Cunningham–Ouchterlony (KCO) empirical fragmentation model and a Multivariate Regression Analysis (MVRA) equation. The research study has analyzed blasting datasets, comprising Geological Strength Index (GSI), number of holes (NH), hole depth (HD), maximum charge per delay (MCPD), total explosive mass (TEM), and boulder size determined by Split-Desktop image analysis. Eight Gaussian Process Regression kernels—squared exponential, rational quadratic, matern with ν = 3/2, and matern with ν = 5/2, both with and without automatic relevance determination (ARD)—were assessed. The GPR model with the ARD matern 3/2 kernel attained superior validation performance of R2 = 0.9016 and RMSE = 4.2482, outperforming the KCO and MVRA models, which displayed significant prediction errors for boulder size. In addition, the sensitivity analysis results demonstrated that GSI and HD were the most influential parameters on boulder size, followed by NH, MCPD, and TEM, accordingly. The findings indicate that GPR, especially when employing ARD matern kernels, precisely estimates the boulder size, and thus can serve as a viable method for optimizing blast design and facilitate efficient boulder management in surface mining operations.
- 2 February 2026
- Published by MDPI AG in Algorithms
- Vol. 19 (2) , 120
Open AccessProbabilistic Prediction of Oversized Rock Fragments in Bench Blasting Using Gaussian Process Regression: A Comparative Study with Empirical and Multivariate Regression Analysis Models
Oversized rock fragments (boulders) produced during bench blasting adversely affect the efficiency of mining downstream processes such as loading, hauling, and crushing, thus leading to regularly requiring costly secondary breakage and the use of mechanized rock breakers. This study presents a probabilistic framework for forecasting boulder size in surface mining operations by employing Gaussian Process Regression (GPR), benchmarked against the Kuznetsov–Cunningham–Ouchterlony (KCO) empirical fragmentation model and a Multivariate Regression Analysis (MVRA) equation. The research study has analyzed blasting datasets, comprising Geological Strength Index (GSI), number of holes (NH), hole depth (HD), maximum charge per delay (MCPD), total explosive mass (TEM), and boulder size determined by Split-Desktop image analysis. Eight Gaussian Process Regression kernels—squared exponential, rational quadratic, matern with ν = 3/2, and matern with ν = 5/2, both with and without automatic relevance determination (ARD)—were assessed. The GPR model with the ARD matern 3/2 kernel attained superior validation performance of R2 = 0.9016 and RMSE = 4.2482, outperforming the KCO and MVRA models, which displayed significant prediction errors for boulder size. In addition, the sensitivity analysis results demonstrated that GSI and HD were the most influential parameters on boulder size, followed by NH, MCPD, and TEM, accordingly. The findings indicate that GPR, especially when employing ARD matern kernels, precisely estimates the boulder size, and thus can serve as a viable method for optimizing blast design and facilitate efficient boulder management in surface mining operations.
- 13 September 2025
- Published by Elsevier in Construction and Building Materials
- Vol. 495
Damage evolution laws and constitutive model description of loess-slag-based cemented backfill material
- 13 September 2025
- Published by Elsevier in Construction and Building Materials
- Vol. 495
Damage evolution laws and constitutive model description of loess-slag-based cemented backfill material
- Open Access
Geotechnical Design of Barrier Pillar Between Boxcut and Underground Mining for Shallow Dipping Orebodies: A Case Study
A barrier pillar between the surface and underground mining sections provides a critical buffer zone in the transition from the boxcut highwall to underground sections by isolating stress fields from underground sections and preventing them from affecting the boxcut highwall slope. In this study, an empirical scaled span method and Rocscience RS2 software were used to conduct parametric studies on key parameters for designing barrier pillars and analyzing the room and pillar design for a planned underground mine on the Great Dyke, Zimbabwe. The approach included analyzing the effect of barrier pillar width, assuming a 10° dipping angle of the orebody, with room and pillar dimensions of 7 m and 6 m, respectively. The impact on boxcut slope stability and the roof of the first stope was monitored. The stability of the barrier pillar was analyzed for varying widths (6 m, 10 m, 20 m, 30 m, and 40 m) and orebody dipping angles (0°, 10°, 20°, 30°, and 40°). The effect of deteriorated rock mass conditions, represented by Geological Strength Index (GSI) values from 30 to 50, was assessed. The optimum room and pillar design was evaluated against the planned 6 m pillar sizes. This comprehensive study aims to support the integrity and longevity of the critical structures of the mining operation.
Open AccessGeotechnical Design of Barrier Pillar Between Boxcut and Underground Mining for Shallow Dipping Orebodies: A Case Study
A barrier pillar between the surface and underground mining sections provides a critical buffer zone in the transition from the boxcut highwall to underground sections by isolating stress fields from underground sections and preventing them from affecting the boxcut highwall slope. In this study, an empirical scaled span method and Rocscience RS2 software were used to conduct parametric studies on key parameters for designing barrier pillars and analyzing the room and pillar design for a planned underground mine on the Great Dyke, Zimbabwe. The approach included analyzing the effect of barrier pillar width, assuming a 10° dipping angle of the orebody, with room and pillar dimensions of 7 m and 6 m, respectively. The impact on boxcut slope stability and the roof of the first stope was monitored. The stability of the barrier pillar was analyzed for varying widths (6 m, 10 m, 20 m, 30 m, and 40 m) and orebody dipping angles (0°, 10°, 20°, 30°, and 40°). The effect of deteriorated rock mass conditions, represented by Geological Strength Index (GSI) values from 30 to 50, was assessed. The optimum room and pillar design was evaluated against the planned 6 m pillar sizes. This comprehensive study aims to support the integrity and longevity of the critical structures of the mining operation.