Tassos G. Karayiannis
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Tassos G. Karayiannis has a total of 63 co-authors. Here are the top co-authors by number of shared publications:
- Mohamed M. Mahmoud
Zagazig Univ, Fac Engn, Environm Engn Dept, Zagazig 44519, Egypt
10 shared publications David B. R. Kenning
College of Engineering, Design and Physical Sciences, Brunel University London, United Kingdom
4 shared publicationsJohn S. Lewis
4 shared publications- Gary Henderson3 shared publications
Mohamed M. Mahmoud
Faculty of Engineering, Zagazig University, Zagazig 44519, Egypt
3 shared publicationsAli H. Al-Zaidi
2 shared publications
Latest Publications
- Open Access
- 6 November 2025
- Published by Elsevier in Applied Thermal Engineering
- Vol. 283
Flow boiling in micro-pin fin heat exchangers and comparison with correlations
- 6 November 2025
- Published by Elsevier in Applied Thermal Engineering
- Vol. 283
Open AccessFlow boiling in micro-pin fin heat exchangers and comparison with correlations
- Open Access
- 11 June 2025
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 251
Flow boiling heat transfer in a single microchannel and comparison with correlations
- 11 June 2025
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 251
Open AccessFlow boiling heat transfer in a single microchannel and comparison with correlations
- Open Access
- 20 February 2025
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 242, 126830
Bubble nucleation site density, generation frequency and departure diameter in flow boiling of HFE-7100
- 20 February 2025
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 242, 126830
Open AccessBubble nucleation site density, generation frequency and departure diameter in flow boiling of HFE-7100
- Open Access
- 1 March 2024
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 224
Flow boiling pressure drop correlation in small to micro passages
- 1 March 2024
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 224
Open AccessFlow boiling pressure drop correlation in small to micro passages
- Open Access
- 18 January 2024
- Published by Oxford University Press (OUP) in International Journal of Low-Carbon Technologies
- Vol. 19, 2068-2085
Performance of vacuum-insulated central pipes for deep borehole heat exchangers in geothermal systems
Geothermal energy is considered a promising future energy prospect, with the geothermal well outlet temperature being one of the important parameters affecting possible utilization options. For ground source heat pump applications or direct district heating, using lower temperatures can be acceptable. However, efficient electricity production requires a higher enthalpy gradient, which cannot be achieved without high temperature at the wellhead. The selection of the dry co-axial close-loop deep borehole systems (DBHE) may be, in some cases, very beneficial. The operating performance of co-axial DBHE can be optimized if the undesired heat transfer between the central pipe and annular fluid zones is minimized. Therefore, the operational performance of such a system depends strongly on the high thermal resistance of the central pipe. The most common option would be a low thermal conductivity material, such as high-density polyethylene (HDPE). In addition, vacuum-insulated tubing (VIT) used as the central pipe could be considered. The article presents results from the study aimed at the comparison of the homogeneous central pipe made of HDPE material and the gap-insulated central pipe. In the study, various air pressure levels as well as variations of surface emissivity were examined to reveal the effect on the heat transfer between the fluid channels. The simulation has been performed using a new purposely developed WellTH simulation software. A coaxial heat exchanger system using a VIT outperforms significantly the heat exchanger with an HDPE for deep geothermal wells. However, this advantage diminishes for shallow wells and therefore this tendency should be considered in the design stage.
- 18 January 2024
- Published by Oxford University Press (OUP) in International Journal of Low-Carbon Technologies
- Vol. 19, 2068-2085
Open AccessPerformance of vacuum-insulated central pipes for deep borehole heat exchangers in geothermal systems
Geothermal energy is considered a promising future energy prospect, with the geothermal well outlet temperature being one of the important parameters affecting possible utilization options. For ground source heat pump applications or direct district heating, using lower temperatures can be acceptable. However, efficient electricity production requires a higher enthalpy gradient, which cannot be achieved without high temperature at the wellhead. The selection of the dry co-axial close-loop deep borehole systems (DBHE) may be, in some cases, very beneficial. The operating performance of co-axial DBHE can be optimized if the undesired heat transfer between the central pipe and annular fluid zones is minimized. Therefore, the operational performance of such a system depends strongly on the high thermal resistance of the central pipe. The most common option would be a low thermal conductivity material, such as high-density polyethylene (HDPE). In addition, vacuum-insulated tubing (VIT) used as the central pipe could be considered. The article presents results from the study aimed at the comparison of the homogeneous central pipe made of HDPE material and the gap-insulated central pipe. In the study, various air pressure levels as well as variations of surface emissivity were examined to reveal the effect on the heat transfer between the fluid channels. The simulation has been performed using a new purposely developed WellTH simulation software. A coaxial heat exchanger system using a VIT outperforms significantly the heat exchanger with an HDPE for deep geothermal wells. However, this advantage diminishes for shallow wells and therefore this tendency should be considered in the design stage.
- 1 January 2024
- Published by Avestia Publishing in Journal of Fluid Flow, Heat and Mass Transfer
- Vol. 11 (1) , 187
Pressure Drop and Heat Transfer Characteristics in a Microchannel with Pin-Fins
The Volume 11, published for JFFHMT Journal.
- 1 January 2024
- Published by Avestia Publishing in Journal of Fluid Flow, Heat and Mass Transfer
- Vol. 11 (1) , 187
Pressure Drop and Heat Transfer Characteristics in a Microchannel with Pin-Fins
The Volume 11, published for JFFHMT Journal.
- Open Access
- 7 July 2023
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 215
Influence of system pressure on flow boiling in microchannels
- 7 July 2023
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 215
Open AccessInfluence of system pressure on flow boiling in microchannels
- Open Access
- 28 March 2023
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 209
Bubble growth on a smooth metallic surface at atmospheric and sub-atmospheric pressure
- 28 March 2023
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 209
Open AccessBubble growth on a smooth metallic surface at atmospheric and sub-atmospheric pressure
- Open Access
- 21 March 2023
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 208
Bubble growth models in saturated pool boiling of water on a smooth metallic surface: Assessment and a new recommendation
- 21 March 2023
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 208
Open AccessBubble growth models in saturated pool boiling of water on a smooth metallic surface: Assessment and a new recommendation
- Open Access
- 11 January 2023
- Published by Akademia Baru Publishing in CFD Letters
- Vol. 15 (1) , 67-75
Flow Distribution in Parallel Rectangular Multi Microchannels in Single Phase
This study proposed newly designed inlet manifolds to manage non-uniformity in parallel multi microchannel heat sink by introducing edges with a curved shape were introduced in order to reduce flow-recirculation at the sharp edges. This resulted in a better flow distribution in the parallel channels. A comprehensible numerical study has been performed using ANSYS-Fluent and a three-dimensional computational domain, incorporating the effect of conjugated heat transfer, was employed in this study. R134a was used as the working fluid and copper was selected as the heat sink material. The dimensionless channel flow ratio and flow maldistribution factor were introduced to quantify the flow distribution inside individual channels and the uniformity of this flow distribution. A uniform flow distribution is achieved when the maldistribution factor value approaches 0.
- 11 January 2023
- Published by Akademia Baru Publishing in CFD Letters
- Vol. 15 (1) , 67-75
Open AccessFlow Distribution in Parallel Rectangular Multi Microchannels in Single Phase
This study proposed newly designed inlet manifolds to manage non-uniformity in parallel multi microchannel heat sink by introducing edges with a curved shape were introduced in order to reduce flow-recirculation at the sharp edges. This resulted in a better flow distribution in the parallel channels. A comprehensible numerical study has been performed using ANSYS-Fluent and a three-dimensional computational domain, incorporating the effect of conjugated heat transfer, was employed in this study. R134a was used as the working fluid and copper was selected as the heat sink material. The dimensionless channel flow ratio and flow maldistribution factor were introduced to quantify the flow distribution inside individual channels and the uniformity of this flow distribution. A uniform flow distribution is achieved when the maldistribution factor value approaches 0.