Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Fu Zhao has a total of 156 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Prospective Life Cycle Assessment of Aluminum-to-Hydrogen Systems with Gallium Recovery for Heavy Duty Transport

    by Xiaohan Wu, Venkat Roy, Nadezhda N. Zyaykina, Fu Zhao

    Hydrogen-assisted heavy-duty transportation has attracted increasing attention as a potential low-carbon pathway for freight decarbonization. This study presents a prospective well-to-wheel life cycle assessment (LCA) of an aluminum-based onboard hydrogen generation system with gallium recovery for Class-8 heavy-duty trucks. Hydrogen is generated through Al-Ga-In-Sn alloy hydrolysis and partially substitutes diesel during vehicle operation. Experimental gallium recovery was conducted to develop life cycle inventory (LCI) data for the recycling subsystem. Results show that environmental performance strongly depends on material sourcing. Using primary aluminum leads to life cycle greenhouse gas (GHG) emissions exceeding 1000 kg CO2-eq per 100 km, whereas recycled aluminum and recycled gallium reduce emissions to approximately 150-170 kg CO 2-eq per 100 km, lower than the baseline diesel scenario. A 40% hydrogen blending ratio provides the lowest GHG 1 emission scenario. Compared with conventional hydrogen pathways, the system only outperforms grey hydrogen but remains less favorable than blue and green hydrogen pathways. The results highlight the importance of secondary aluminum utilization and gallium recycling for reducing the environmental impacts of the on-site aluminum-to-hydrogen system.

  • Open Access

    Declining Copper Ore Grades Highlight the Economic and Environmental Resilience of Heap Bioleaching  

    by Xiaohan Wu, Xinbo Yang, Michael L. Free, Rick Q. Honaker, Fu Zhao

    Copper demand is expected to increase substantially due to global electrification and renewable energy expansion, while the average ore grade continues to decline. This study conducts a comprehensive techno-economic analysis (TEA) and life cycle assessment (LCA) comparing the conventional pyrometallurgy process with an emerging alternative, heap bioleaching, across ore grades from 0.6% to 0.2%. Energy and material requirements were modeled using grade-dependent scaling of process inventories, and uncertainty was quantified through pedigree-based and expert-elicited parameters. The results show that heap bi-1 oleaching achieves 10-40% lower production costs and 30-50% lower life cycle greenhouse gas (GHG) emissions compared with the pyrometallurgical route, with the advantage increasing as ore grade declines. Environmentally, heap bioleaching substantially reduces global warming and fossil fuel depletion impacts but increases ecotoxicity and eutrophication potentials due to greater tailings mass. These trade-offs emphasize the need for improved tailings treatment and reagent management in future bio-hydrometallurgical systems. Overall, the findings provide quantitative insight into how declining ore grades reshape the environmental and economic competitiveness of alternative copper production routes.

  • Open Access

    Declining Copper Ore Grades Highlight the Economic and Environmental Resilience of Heap Bioleaching

    by Xiaohan Wu, Xinbo Yang, Michael L. Free, Rick Q. Honaker, Fu Zhao

    Copper demand is expected to increase substantially due to global electrification and renewable energy expansion, while the average ore grade continues to decline. This study conducts a comprehensive techno-economic analysis (TEA) and life cycle assessment (LCA) comparing the conventional pyrometallurgy process with an emerging alternative, heap bioleaching, across ore grades from 0.6% to 0.2%. Energy and material requirements were modeled using grade-dependent scaling of process inventories, and uncertainty was quanti f ied through pedigree-based and expert-elicited parameters. The results show that heap bioleaching achieves 10–40% lower production costs and 30–50% lower life cycle greenhouse gas (GHG) emissions compared with the pyrometallurgical route, with the advantage increasing as ore grade declines. Environmentally, heap bioleaching substantially reduces global warming and fossil fuel depletion impacts but increases ecotoxicity and eutrophication potentials due to greater tailings mass. These trade-offs emphasize the need for improved tailings treatment and reagent management in future bio-hydrometallurgical systems. Overall, the findings provide quantitative insight into how declining ore grades reshape the environmental and economic competitiveness of alternative copper production routes.

  • Open Access

    Integrating Carbon Capture into Copper Comminution: A Combined Techno-Economic Assessment and Carbon Footprint Analysis

    by Xiaohan Wu, Xu Wang, Yi Wang, Wencai Zhang, Rick Honaker, Fu Zhao

    Copper production is highly energy-intensive, with comminution (crushing and grinding) accounting for a major portion of both energy use and greenhouse gas (GHG) emissions. This study evaluates the environmental and economic performance of integrating carbon capture into the copper comminution process through a combined LCA and TEA. The improved scenario introduces a CO 2 pretreatment step into the grinding circuit and is benchmarked against a conventional baseline process. The LCA results show that integrating CO 2 pretreatment into the comminution process reduces grinding energy consumption from approximately 4,700 kWh to 3,900 kWh per ton of copper. Combined with the embodied carbon emissions of the carbon capture system, the net greenhouse gas (GHG) reduction is approximately 1.2 ton CO 2 -eq per ton of copper, corresponding to an overall reduction of approximately 35% relative to the baseline. Economically, the total production cost increases by approximately 480 USD per ton of copper, primarily due to the expenses associated with CO 2 procurement and compression. Although this increase exceeds typical cost margins for comminution, uncertainty analysis indicates that the CO 2 price remains the dominant. contributor to cost variability, while the GHG reduction benefit remains robust across parameter ranges. When CO 2 is instead sourced from flue gas streams generated by fossil-fuel combustion, the procurement cost is eliminated, resulting in a cost saving of roughly 90 USD per ton compared with the baseline scenario (without CO 2 pretreatment). Overall, these results demonstrate that CO 2 pretreatment represents a previously unexplored, yet technically viable and scalable decarbonization pathway for energy-intensive copper production systems.


  • Open Access

    Transforming E-Waste Into Strategic Resources: Techno-Economic Analysis of Gallium and By-products Recovery from LEDs via Bioleaching

    by Xiaohan Wu, Venkat Roy, Yiming Liu, Neha Shakelly, Tapajyoti Ghosh, Xinbo Yang, John W. Sutherland, Fu Zhao

    The growing demand for gallium in optoelectronics and renewable energy applications raises concerns about supply security and production sustainability. This study evaluates the techno-economic feasibility of recovering gallium and by-products (copper and nickel) from waste GaN-based LEDs via bioleaching. A process flowsheet encompassing transportation, robotic disassembly, ball milling, bioleaching, solvent extraction/electrowinning, and refining was modeled. Based on mass balance analysis, more than 33,000 tons of LED waste are required annually to yield 22 kg of gallium alongside substantial copper and nickel coproducts. Preliminary techno-economic analysis (TEA) shows an average total cost (ATC) of 9.07 USD/kg metal when allocated to market prices, corresponding to 8.96 USD/kg for copper, 21.1 USD/kg for nickel, and 624.5 USD/kg for gallium. For gallium, direct operational costs account for more than 70% of the cost. Monte Carlo simulations further quantify cost uncertainties under market price fluctuations. This work represents the first TEA of gallium recovery from GaN-based LEDs and highlights potential pathways for future cost reduction.

  • Open Access

    Life cycle assessment for primary gallium production at industrial-scale

    by Hao Luo, Tai-Yuan Huang, Xiaohan Wu, Fu Zhao

    Purpose: This study aims to provide a comprehensive life cycle assessment (LCA) of primary gallium production on an industrial scale, addressing sustainability concerns due to its intensive chemical and energy consumption. The research question focuses on identifying the environmental impacts across each production process and suggesting mitigation strategies. Methods: Data from a gallium production plant in China was utilized to quantify environmental impacts. The LCA followed the standard four-phase process, including goal and scope definition, inventory analysis, life cycle impact assessment (LCIA), and result interpretation. The ReCiPe 2016 (Midpoint) method was applied for LCIA, and the study considered 14 energy scenarios to assess the carbon footprint under different energy sources. Results and discussion: Key findings indicate that sodium hydroxide and electricity usage are major contributors to environmental burdens such as global warming potential and human toxicity. Data quality analysis highlights the necessity of using high-quality, industrial-scale data in accurate assessment of gallium environmental impacts. In addition, comparison analysis between primary and secondary gallium production shows the challenges of intensive energy and chemical usage during gallium recycling. The study suggests that optimizing production processes and transitioning to cleaner energy sources can effectively mitigate environmental footprints while meeting the growing demand for gallium. Conclusions: The study offers a detailed process inventory for primary gallium production, identifying key emission hotspots and providing insights into potential mitigation strategies. It concludes that significant environmental benefits can be achieved through process optimization and the adoption of renewable energy sources, aligning with global sustainability goals.


  • Open Access

    Agile synthesis and automated, high-throughput evaluation of diglycolamides for liquid–liquid extraction of rare-earth elements

    by Lun An, Yue Yao, Tyler B. Hall, Fu Zhao, Long Qi

    Liquid–liquid extraction is one of the most scalable processes to produce rare-earth elements (REEs) from natural and recycled resources. Accelerating the research, development, and deployment (RD&D) of sustainable processes to manufacture REEs requires both facile synthesis of extractive ligands at scale and fast evaluation of process conditions. Here, we establish an integrated RD&D methodology comprised of agile ligand synthesis and automated high-throughput extraction studies. Using diglycolamides (DGAs) as an example, we first developed a method for DGA synthesis (scalable to 200 g) by directly coupling diglycolic acid and secondary amines via the solvent-free melt-amidation reaction. A substrate scope of the melt-amidation synthesis was demonstrated for 9 different DGAs with good yields (85–96%) and purities (88–96%) without any post-reaction workup or purification process. Life cycle assessment shows that our synthesis method outperforms the prior-art pathway in each environmental impact category, especially showing a 67% reduction in global warming potential. Furthermore, we investigate the structure–activity relationship of various alkyl-substituted DGAs using an automated, high-throughput workflow for liquid–liquid extraction, achieving over 180 runs in 48 hours. The acquired data enables the development of a promising flowsheet for separating light and heavy REEs. The integrated RD&D method of agile synthesis and automated, high-throughput extraction studies paves the way for future iterative development of sustainable production of REEs and other critical materials to meet the needs for clean energy transformation.


  • Integrated Circular Economy Model System for Direct Lithium Extraction: From Minerals to Batteries Utilizing Aluminum Hydroxide

    by K. Jayanthi, Tej N. Lamichhane, Venkat Roy, Fu Zhao, Alexandra Navrotsky, Bruce A. Moyer, Mariappan Parans Paranthaman

    Aluminum hydroxide, an abundant mineral found in nature, exists in four polymorphs: gibbsite, bayerite, nordstrandite, and doyleite. Among these polymorphs gibbsite, bayerite, and commercially synthesized amorphous aluminum hydroxide have been investigated as sorbent materials for lithium extraction from sulfate solutions. The amorphous form of Al(OH)3 exhibits a reactivity higher than that of the naturally occurring crystalline polymorphs in terms of extracting Li+ ions. This study employed high-temperature oxide melt solution calorimetry to explore the energetics of the sorbent polymorphs. The enthalpic stability order was measured to be gibbsite > bayerite > amorphous Al(OH)3. The least stable form, amorphous Al(OH)3, undergoes a spontaneous reaction with lithium, resulting in the formation of a stable layered double hydroxide phase. Consequently, amorphous Al(OH)3 shows promise as a sorbent material for selectively extracting lithium from clay mineral leachate solutions. This research demonstrates the selective direct extraction of Li+ ions using amorphous aluminum hydroxide through a liquid-solid lithiation reaction, followed by acid-free delithiation and relithiation processes, achieving an extraction efficiency of 86%, and the maximum capacity was 37.86 mg·g-1 in a single step during lithiation. With high selectivity during lithiation and nearly complete recoverability of the sorbent material during delithiation, this method presents a circular economy model. Furthermore, a life cycle analysis was conducted to illustrate the environmental advantages of replacing the conventional soda ash-based precipitation process with this method, along with a simple operational cost analysis to evaluate reagent and fuel expenses.


  • Comparative Life Cycle Assessment of Injection Molded and Big Area Additive Manufactured NdFeB Bonded Permanent Magnets

    by Sameer Kulkarni, Fu Zhao, Ikenna C. Nlebedim, Robert Fredette, Mariappan Parans Paranthaman

    Permanent magnets are expected to play a crucial role in the realization of the clean economy. In particular, the neodymium–iron–boron (Nd2Fe14B or NdFeB) magnets, which have the highest energy density among rare earth permanent magnets, are needed for building more efficient windmill generators, electric vehicle motors, etc. Currently, near-net shape magnets can be either made through sintering and compression molding with extensive post machining or directly through injection molding. However, injection molding has a loading volume fraction limitation of 0.65 for nylon binders. A novel method of manufacturing bonded permanent magnets with loading fraction greater than 0.65 has been demonstrated using big area additive manufacturing (BAAM) printers. As energy density is directly proportional to the square of the magnet loading fraction, magnets produced using BAAM printers require less volume and magnetic material compared to that of injection molded magnets on average. A comparative life cycle assessment shows that this difference in magnetic powder consumption nearly constitutes the difference in the environmental impact categories. Even after assuming recycled magnetic input, the BAAM magnets perform better environmentally than injection molded magnets, especially in the ozone depletion category. Since BAAM printers can accommodate even higher loading fractions, at scale, BAAM printers possibly can bring about a significant decrease in rare earth mineral consumption and environmental emissions. Furthermore, single screw extrusion enables BAAM printers to have high print speeds and allow them to be economically competitive against injection molding. Therefore, BAAM printed magnets show great promise in transitioning towards the clean economy.