Tanusree Bera
Research Subjects
Tanusree Bera has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
Smita Mohanty
School for Advanced Research in Petrochemicals: Laboratory for Advanced Research in Polymeric Materials (LARPM), Centre Institute of Petrochemicals Engineering and Technology (CIPET), Bhubaneswar, India
6 shared publications- Samir Kumar Acharya
Department of Mechanical Engineering, NIT Rourkela, Rourkela 769008, Odisha, India
4 shared publications - Ved Prakash
Department of Mechanical Engineering, National Institute of Technology Rourkela, Rourkela, India
3 shared publications Goutam Sutradhar
Department of Mechanical Engineering, National Institute of Technology Manipur, Manipur, India
2 shared publicationsVed Prakash
National Institute of Technology Rourkela
2 shared publicationsLopamundra Mohapatra
Indian Institute of Technology Kharagpur
1 shared publication
Latest Publications
- 16 April 2026
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 37 (11) , 830
FDM-fabricated ABS/CuO–MWCNT nanocomposites for enhanced mechanical and triboelectric performance
- 16 April 2026
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 37 (11) , 830
FDM-fabricated ABS/CuO–MWCNT nanocomposites for enhanced mechanical and triboelectric performance
- 24 March 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
Innovative splinting solutions: Additive manufacturing of acrylonitrile butadiene styrene-based mallet finger orthoses
Mallet finger is a common deformity of the distal interphalangeal joint resulting from extensor tendon injury, frequently observed in athletes and individuals exposed to high-impact fingertip trauma. To address limitations in conventional splinting methods, this study introduces two ergonomic mallet finger splint designs fabricated using acrylonitrile butadiene styrene via fused deposition modeling 3D printing. These designs—a modular two-piece splint with Velcro fastening and a single-piece cylindrical splint—incorporate strategically placed ventilation holes to enhance airflow, reduce perspiration, and improve patient comfort during prolonged wear. Microstructural evaluation using scanning electron microscopy revealed characteristic inter-bead voids and interlayer bonding typical of fused deposition modeling-printed acrylonitrile butadiene styrene, while post-aging samples exhibited signs of embrittlement and microcrack formation. These morphological changes were correlated with mechanical performance, where tensile strength (30.73 MPa), modulus of elasticity (1.59 GPa), and other key properties showed only marginal reductions (2–4.7%) after thermal aging at 60 °C for seven weeks, confirming the material's structural stability. The integration of microstructural insights with mechanical data validates acrylonitrile butadiene styrene as a durable, biocompatible, and thermally stable material for orthopedic applications, offering a practical and customizable alternative to traditional mallet finger treatments.
- 24 March 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
Innovative splinting solutions: Additive manufacturing of acrylonitrile butadiene styrene-based mallet finger orthoses
Mallet finger is a common deformity of the distal interphalangeal joint resulting from extensor tendon injury, frequently observed in athletes and individuals exposed to high-impact fingertip trauma. To address limitations in conventional splinting methods, this study introduces two ergonomic mallet finger splint designs fabricated using acrylonitrile butadiene styrene via fused deposition modeling 3D printing. These designs—a modular two-piece splint with Velcro fastening and a single-piece cylindrical splint—incorporate strategically placed ventilation holes to enhance airflow, reduce perspiration, and improve patient comfort during prolonged wear. Microstructural evaluation using scanning electron microscopy revealed characteristic inter-bead voids and interlayer bonding typical of fused deposition modeling-printed acrylonitrile butadiene styrene, while post-aging samples exhibited signs of embrittlement and microcrack formation. These morphological changes were correlated with mechanical performance, where tensile strength (30.73 MPa), modulus of elasticity (1.59 GPa), and other key properties showed only marginal reductions (2–4.7%) after thermal aging at 60 °C for seven weeks, confirming the material's structural stability. The integration of microstructural insights with mechanical data validates acrylonitrile butadiene styrene as a durable, biocompatible, and thermally stable material for orthopedic applications, offering a practical and customizable alternative to traditional mallet finger treatments.
- 16 September 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 35 (7) , 6337-6347
Parametric Optimization in Fused Deposition Modeling for Mechanical Reinforcement of Polylactic Acid, Acrylonitrile Butadiene Styrene, and Nylon Carbon Fiber Materials
- 16 September 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 35 (7) , 6337-6347
Parametric Optimization in Fused Deposition Modeling for Mechanical Reinforcement of Polylactic Acid, Acrylonitrile Butadiene Styrene, and Nylon Carbon Fiber Materials
- 6 May 2025
- Published by Wiley in Polymer International
Polylactic acid (PLA) as a tolerant on the thermomechanical and compostability behaviour of poly(butylene adipate‐co‐terephthalate) (PBAT)/thermoplastic starch (TPS) blend
Poly(butylene adipate‐co‐terephthalate) (PBAT) is a biodegradable copolyester consisting of aliphatic and aromatic components, specifically butylene adipate and butylene terephthalate. PBAT offers mechanical properties comparable to those of conventional plastics but is approximately three times more expensive than low‐density polyethylene. Conversely, biopolymers such as starch are cost‐effective but lack sufficient mechanical strength on their own. In this study, the impact of thermoplastic starch (TPS) on the properties of PBAT‐based biodegradable mulch films was investigated. The role of PBAT grafted with maleic anhydride and maleated TPS as compatibilizers in varying compositions of PBAT/TPS blends was examined. The proportion of TPS was maintained at 30%, while PBAT was adjusted to 70% and 60%, focusing on the cost‐effective production of the films. Notably, the addition of 10% polylactic acid as a tolerance enhancer led to significant improvements in the mechanical, morphological and thermal properties of the films. © 2025 Society of Chemical Industry.
- 6 May 2025
- Published by Wiley in Polymer International
Polylactic acid (PLA) as a tolerant on the thermomechanical and compostability behaviour of poly(butylene adipate‐co‐terephthalate) (PBAT)/thermoplastic starch (TPS) blend
Poly(butylene adipate‐co‐terephthalate) (PBAT) is a biodegradable copolyester consisting of aliphatic and aromatic components, specifically butylene adipate and butylene terephthalate. PBAT offers mechanical properties comparable to those of conventional plastics but is approximately three times more expensive than low‐density polyethylene. Conversely, biopolymers such as starch are cost‐effective but lack sufficient mechanical strength on their own. In this study, the impact of thermoplastic starch (TPS) on the properties of PBAT‐based biodegradable mulch films was investigated. The role of PBAT grafted with maleic anhydride and maleated TPS as compatibilizers in varying compositions of PBAT/TPS blends was examined. The proportion of TPS was maintained at 30%, while PBAT was adjusted to 70% and 60%, focusing on the cost‐effective production of the films. Notably, the addition of 10% polylactic acid as a tolerance enhancer led to significant improvements in the mechanical, morphological and thermal properties of the films. © 2025 Society of Chemical Industry.
- 3 March 2025
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 142 (22)
Design and Characterization of 3D‐Printed Capacitors Using Conductive and Non‐Conductive PLA Filaments
Recent advancements have sparked significant interest in 3D‐printed electronics, with transformative potential for the electronics industry. The capability to design custom electronic devices tailored to precise specifications has elevated 3D‐printed electronics as a field of immense potential. In our work, we are exploring material extrusion (MEX) techniques to fabricate capacitors using polylactic acid (PLA) as the primary polymer. This research focuses on analyzing the mechanical and electrical properties of both conductive PLA and PLA‐based capacitors. The capacitors are created by 3D‐printing structured layers, where PLA serves as the dielectric material, and conductive PLA forms the electrodes. This design enables a viable pathway for developing capacitors with enhanced capacitance, making them suitable candidates for advanced energy storage applications.
- 3 March 2025
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 142 (22)
Design and Characterization of 3D‐Printed Capacitors Using Conductive and Non‐Conductive PLA Filaments
Recent advancements have sparked significant interest in 3D‐printed electronics, with transformative potential for the electronics industry. The capability to design custom electronic devices tailored to precise specifications has elevated 3D‐printed electronics as a field of immense potential. In our work, we are exploring material extrusion (MEX) techniques to fabricate capacitors using polylactic acid (PLA) as the primary polymer. This research focuses on analyzing the mechanical and electrical properties of both conductive PLA and PLA‐based capacitors. The capacitors are created by 3D‐printing structured layers, where PLA serves as the dielectric material, and conductive PLA forms the electrodes. This design enables a viable pathway for developing capacitors with enhanced capacitance, making them suitable candidates for advanced energy storage applications.
- 28 January 2025
- Published by Wiley in Materialwissenschaft und Werkstofftechnik
- Vol. 56 (2) , 226-234
Implementation of Taguchi design for dry sliding wear of high density polyethylene/silicon carbide composite
The present work focus on the optimization of dry sliding wear behavior operating parameters of high density polyethylene/silicon carbide composites carried out with Taguchi method. The various control factors such as filler content, applied load and sliding velocity were selected at three different levels of each. The specific wear rate and coefficient of friction were selected as performance output. The dry sliding wear studies revealed that the coefficient of friction increases with an increase in applied load and sliding velocity. The specific wear rate for all composites increased with an increase in applied force. Nine experimental runs were performed using Taguchi L9 orthogonal array. The optimum control factors were predicted according to the MINITAB16 software. Analysis of variance has been applied to predict the highly significant operating parameter. The analysis of variance analysis revealed that the applied load is the most important control factor out of all the other control factors, followed by filler content and sliding velocity, of dry sliding wear behavior of high density polyethylene/silicon carbide composites.
- 28 January 2025
- Published by Wiley in Materialwissenschaft und Werkstofftechnik
- Vol. 56 (2) , 226-234
Implementation of Taguchi design for dry sliding wear of high density polyethylene/silicon carbide composite
The present work focus on the optimization of dry sliding wear behavior operating parameters of high density polyethylene/silicon carbide composites carried out with Taguchi method. The various control factors such as filler content, applied load and sliding velocity were selected at three different levels of each. The specific wear rate and coefficient of friction were selected as performance output. The dry sliding wear studies revealed that the coefficient of friction increases with an increase in applied load and sliding velocity. The specific wear rate for all composites increased with an increase in applied force. Nine experimental runs were performed using Taguchi L9 orthogonal array. The optimum control factors were predicted according to the MINITAB16 software. Analysis of variance has been applied to predict the highly significant operating parameter. The analysis of variance analysis revealed that the applied load is the most important control factor out of all the other control factors, followed by filler content and sliding velocity, of dry sliding wear behavior of high density polyethylene/silicon carbide composites.
- 27 November 2024
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (16) , 17106-17120
Mechanical Properties of Polylactic Acid/Chitosan Composites by Fused Deposition Modeling
- 27 November 2024
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (16) , 17106-17120
Mechanical Properties of Polylactic Acid/Chitosan Composites by Fused Deposition Modeling
- 1 August 2024
- Published by SAGE Publications in 3D Printing and Additive Manufacturing
- Vol. 11 (4) , 1462-1470
A Review on Residual Stress in Metal Additive Manufacturing
A new method for producing parts in the expanding sector is additive manufacturing. The appropriate name for three-dimensional (3D) printing is additive manufacturing because it produces the part layer by layer. Plastics and metals can be 3D printed in large quantities with the precise surface finish and feature quality needed in additive manufacturing. More specifically, direct metal sintering, direct energy deposition, and metal binder jetting are used in 3D printing. The computer-aided design model is completed when the powder bed has been successively scanned and lowered. The metal sintering process uses a powder bed with powder metal, and laser selectively melts a flattened bed of powder, which is done with roller with successive rolling of new layer on previous into desired shape before a new layer is pushed on top of the previous layer. As a result, the new layer has solidified on top of the earlier layer, causing the prior layer to melt back again. Because of the unique thermal cycle, this results in residual stress (RS). The unique thermal cycle of metal additive manufacturing is characterized by (1) rapid heating rate caused by high energy intensity and steep temperature gradients; (2) rapid solidification with high cooling rates because of the small volume of melt pool; and (3) melt back, which involves simultaneous melting of the top powder layer and re-melting of underlying previously solidified layers. The presence of RS in metal additive manufacturing (AM) creates difficulties that restrict the process's ability to produce parts at an industrial scale. During and after manufacturing, these forces may cause parts to distort and crack. This can be solved by heating the powder bed, which will lessen this type of issue. The causes, traits, and reduction of RS are the main topics of this review article. A number of conceptual approaches to reducing RS are addressed to provide some useful inspiration for creating a methodical RS balancing procedure for AM. These approaches are based on the state and future of the relevant techniques.
- 1 August 2024
- Published by SAGE Publications in 3D Printing and Additive Manufacturing
- Vol. 11 (4) , 1462-1470
A Review on Residual Stress in Metal Additive Manufacturing
A new method for producing parts in the expanding sector is additive manufacturing. The appropriate name for three-dimensional (3D) printing is additive manufacturing because it produces the part layer by layer. Plastics and metals can be 3D printed in large quantities with the precise surface finish and feature quality needed in additive manufacturing. More specifically, direct metal sintering, direct energy deposition, and metal binder jetting are used in 3D printing. The computer-aided design model is completed when the powder bed has been successively scanned and lowered. The metal sintering process uses a powder bed with powder metal, and laser selectively melts a flattened bed of powder, which is done with roller with successive rolling of new layer on previous into desired shape before a new layer is pushed on top of the previous layer. As a result, the new layer has solidified on top of the earlier layer, causing the prior layer to melt back again. Because of the unique thermal cycle, this results in residual stress (RS). The unique thermal cycle of metal additive manufacturing is characterized by (1) rapid heating rate caused by high energy intensity and steep temperature gradients; (2) rapid solidification with high cooling rates because of the small volume of melt pool; and (3) melt back, which involves simultaneous melting of the top powder layer and re-melting of underlying previously solidified layers. The presence of RS in metal additive manufacturing (AM) creates difficulties that restrict the process's ability to produce parts at an industrial scale. During and after manufacturing, these forces may cause parts to distort and crack. This can be solved by heating the powder bed, which will lessen this type of issue. The causes, traits, and reduction of RS are the main topics of this review article. A number of conceptual approaches to reducing RS are addressed to provide some useful inspiration for creating a methodical RS balancing procedure for AM. These approaches are based on the state and future of the relevant techniques.
- Open Access
- 1 January 2024
- Published by SCIE Publishing Limited in Advanced Materials & Sustainable Manufacturing
- Vol. 1 (1) , 10002
A Review on Significant Role of Additive Manufacturing in Biomedical Applications
Sancang Publishing House is mainly engaged in the publication and distribution of Chinese international open source journals. The journals cover engineering technology, mathematics and physics, humanities and society, information science, economics and management, medicine and health, agriculture, global environment and other disciplines, with the help of Internet thinking and modern Information technology, based on the scientific research needs of domestic universities and research institutions, strives to promote the exchange and dissemination of knowledge in the Chinese academic community. It can be published in journals, published papers, and published quickly. Sancang Publishing welcomes scientific research scholars to join us, participate in manuscript review, co-run journals, submit manuscripts, and grow and grow together with Chinese journals. If you have any comments or suggestions on the journal, please contact service@sciepublish.com.
- 1 January 2024
- Published by SCIE Publishing Limited in Advanced Materials & Sustainable Manufacturing
- Vol. 1 (1) , 10002
Open AccessA Review on Significant Role of Additive Manufacturing in Biomedical Applications
Sancang Publishing House is mainly engaged in the publication and distribution of Chinese international open source journals. The journals cover engineering technology, mathematics and physics, humanities and society, information science, economics and management, medicine and health, agriculture, global environment and other disciplines, with the help of Internet thinking and modern Information technology, based on the scientific research needs of domestic universities and research institutions, strives to promote the exchange and dissemination of knowledge in the Chinese academic community. It can be published in journals, published papers, and published quickly. Sancang Publishing welcomes scientific research scholars to join us, participate in manuscript review, co-run journals, submit manuscripts, and grow and grow together with Chinese journals. If you have any comments or suggestions on the journal, please contact service@sciepublish.com.
- 29 April 2022
- Published by Springer Nature
- p. 545-554
Abrasive Wear Behavior of Bio-Fiber-Reinforced Epoxy Composites with Taguchi Approach
- 29 April 2022
- Published by Springer Nature
- p. 545-554
Abrasive Wear Behavior of Bio-Fiber-Reinforced Epoxy Composites with Taguchi Approach