Marie-Hélène Mathon
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Marie-Hélène Mathon has a total of 35 co-authors. Here are the top co-authors by number of shared publications:
- Thierry Baudin
Université Paris-Saclay, CNRS, Institut de Chimie Moléculaire et des Matériaux d’Orsay, 91405 Orsay, France
2 shared publications - Anne-Laure Helbert
Université Paris-Saclay
1 shared publication B. K. Panigrahi
Indira Gandhi Centre for Atomic Research, MSG 2 , Kalpakkam 603 102, Tamil Nadu, India
1 shared publicationBrahim Mehdi
1 shared publicationC.Y. Dan
1 shared publication- Christian Robertson
CEA, Service de Recherche en Matériaux et procédés Avancés, Université Paris-Saclay, 91191 Gif-sur-Yvette, France
1 shared publication
Latest Publications
- 17 February 2024
- Published by Elsevier in International Journal of Mechanical Sciences
- Vol. 270
Measuring texture-component-dependent stress of CuZn39Pb2 by neutron diffraction
- 17 February 2024
- Published by Elsevier in International Journal of Mechanical Sciences
- Vol. 270
Measuring texture-component-dependent stress of CuZn39Pb2 by neutron diffraction
- 3 November 2022
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 132 (17) , 175107
Indentation response of model oxide dispersion strengthening alloys after ion irradiation up to 700 °C
This paper presents an experimental investigation of irradiation-induced evolutions in three different oxide dispersion strengthening (ODS) alloys. High-dose, dual beam Ni–He ion irradiations are carried out up to 700 °C. The significant dose-dependent changes in the ODS particle size and number density are documented and interpreted in terms of specific point defect transport mechanisms, from small angle neutron scattering, TEM, and pulsed low-energy positron system measurements combined. The corresponding micro-mechanical changes in the alloys are evaluated based on the indentation response, which is, in turn, interpreted in terms of related, sub-grain plasticity mechanisms. The room temperature tests (without dwell time) reveal that the microscale work-hardening rate increases with decreasing the particle number density and pronounced strain localization effect. The elevated temperature tests (up to 600 °C, with dwell time) show that the indentation creep compliance is mostly temperature-independent after irradiation up to 25 dpa at Tirr = 500 °C and markedly temperature-dependent, after irradiation beyond 40 dpa at Tirr = 600 °C. This effect is ascribed to particular creep mechanisms associated with indent-induced plasticity, i.e., high stress and high dislocation density conditions.
- 3 November 2022
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 132 (17) , 175107
Indentation response of model oxide dispersion strengthening alloys after ion irradiation up to 700 °C
This paper presents an experimental investigation of irradiation-induced evolutions in three different oxide dispersion strengthening (ODS) alloys. High-dose, dual beam Ni–He ion irradiations are carried out up to 700 °C. The significant dose-dependent changes in the ODS particle size and number density are documented and interpreted in terms of specific point defect transport mechanisms, from small angle neutron scattering, TEM, and pulsed low-energy positron system measurements combined. The corresponding micro-mechanical changes in the alloys are evaluated based on the indentation response, which is, in turn, interpreted in terms of related, sub-grain plasticity mechanisms. The room temperature tests (without dwell time) reveal that the microscale work-hardening rate increases with decreasing the particle number density and pronounced strain localization effect. The elevated temperature tests (up to 600 °C, with dwell time) show that the indentation creep compliance is mostly temperature-independent after irradiation up to 25 dpa at Tirr = 500 °C and markedly temperature-dependent, after irradiation beyond 40 dpa at Tirr = 600 °C. This effect is ascribed to particular creep mechanisms associated with indent-induced plasticity, i.e., high stress and high dislocation density conditions.
- 1 January 2019
- Published by Elsevier in Materials Characterization
- Vol. 147, 242-252
Investigation of microstructure and texture evolution of a Mg/Al laminated composite elaborated by accumulative roll bonding
- 1 January 2019
- Published by Elsevier in Materials Characterization
- Vol. 147, 242-252
Investigation of microstructure and texture evolution of a Mg/Al laminated composite elaborated by accumulative roll bonding
- 1 February 2018
- Published by Elsevier in Materials Characterization
- Vol. 136, 293-301
Cold rolling texture evolution of TiB2 particle reinforced Al-based composites by Neutron Diffraction and EBSD analysis
- 1 February 2018
- Published by Elsevier in Materials Characterization
- Vol. 136, 293-301
Cold rolling texture evolution of TiB2 particle reinforced Al-based composites by Neutron Diffraction and EBSD analysis
- 29 December 2008
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 386-388, 475-478
Study of PM2000 microstructure evolution following FSW process
- 29 December 2008
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 386-388, 475-478
Study of PM2000 microstructure evolution following FSW process
- 1 June 1999
- Published by Elsevier in Comptes Rendus de l'Académie des Sciences - Series IIA - Earth and Planetary Science
- Vol. 328 (11) , 733-738
Étude des déformations élastiques résiduelles dans les quartzites
- 1 June 1999
- Published by Elsevier in Comptes Rendus de l'Académie des Sciences - Series IIA - Earth and Planetary Science
- Vol. 328 (11) , 733-738
Étude des déformations élastiques résiduelles dans les quartzites