Seyed Foad Aghamiri
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Seyed Foad Aghamiri has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
Mohammad Reza Talaie
4 shared publicationsMaryam Montazerolghaem
2 shared publications- Shahram Tangestaninejad
University of Isfahan
2 shared publications A. Moheb
Chemical Engineering Department, Isfahan University of Technology, Isfahan, 84154, Iran
1 shared publication- Ahmad Bayat
Department of Chemical Engineering, Tafresh University, Tafresh 79611-39518, Iran
1 shared publication - Amin Ghobeity
School of Mechanical and Electrical Engineering, Sheridan College, Brampton, ON, Canada
1 shared publication
Latest Publications
- Open Access
- 27 January 2022
- Published by MDPI AG in Nanomaterials
- Vol. 12 (3) , 412
Adsorption of Carbon Dioxide with Ni-MOF-74 and MWCNT Incorporated Poly Acrylonitrile Nanofibers
Among the new adsorbent forms, nanofiber structures have attracted extra attention because of features such as high surface area, controllable properties, and fast kinetics. The objective of this study is to produce the polyacrylonitrile (PAN) electrospun nanofibers loaded with Ni-MOF-74/MWCNT to obtain maximum CO2 adsorption. The prepared PAN/MWCNT/MOF nanofiber based on the Box–Behnken design (BBD) model suggests the CO2 adsorption of about 1.68 mmol/g (at 25 °C and 7 bar) includes 14.61 w/v%, 1.43 w/w%, and 11.9 w/w% for PAN, MWCNT, and MOF, respectively. The results showed the effective CO2 adsorption of about 1.65 ± 0.03 mmol/g (BET = 65 m2/g, pore volume = 0.08 cm3/g), which proves the logical outcomes of the chosen model. The prepared PAN/MWCNT/MOF nanofiber was characterized using different analyzes such as SEM, TEM, TG, XRD, FTIR, and N2 adsorption–desorption isotherms. More MOF mass loading on the nanofiber surface via secondary growth method resulted in 2.83 mmol/g (BET = 353 m2/g, pore volume = 0.22 cm3/g, 43% MOF mass loading) and 4.35 mmol/g (BET = 493 m2/g, pore volume = 0.27 cm3/g, 65% MOF mass loading) CO2 adsorption at 7 bar for the first and second growth cycles, respectively. This indicates that secondary growth is more effective in the MOF loading amount and, consequently, adsorption capacity compared to the MOF loading during electrospinning.
- 27 January 2022
- Published by MDPI AG in Nanomaterials
- Vol. 12 (3) , 412
Open AccessAdsorption of Carbon Dioxide with Ni-MOF-74 and MWCNT Incorporated Poly Acrylonitrile Nanofibers
Among the new adsorbent forms, nanofiber structures have attracted extra attention because of features such as high surface area, controllable properties, and fast kinetics. The objective of this study is to produce the polyacrylonitrile (PAN) electrospun nanofibers loaded with Ni-MOF-74/MWCNT to obtain maximum CO2 adsorption. The prepared PAN/MWCNT/MOF nanofiber based on the Box–Behnken design (BBD) model suggests the CO2 adsorption of about 1.68 mmol/g (at 25 °C and 7 bar) includes 14.61 w/v%, 1.43 w/w%, and 11.9 w/w% for PAN, MWCNT, and MOF, respectively. The results showed the effective CO2 adsorption of about 1.65 ± 0.03 mmol/g (BET = 65 m2/g, pore volume = 0.08 cm3/g), which proves the logical outcomes of the chosen model. The prepared PAN/MWCNT/MOF nanofiber was characterized using different analyzes such as SEM, TEM, TG, XRD, FTIR, and N2 adsorption–desorption isotherms. More MOF mass loading on the nanofiber surface via secondary growth method resulted in 2.83 mmol/g (BET = 353 m2/g, pore volume = 0.22 cm3/g, 43% MOF mass loading) and 4.35 mmol/g (BET = 493 m2/g, pore volume = 0.27 cm3/g, 65% MOF mass loading) CO2 adsorption at 7 bar for the first and second growth cycles, respectively. This indicates that secondary growth is more effective in the MOF loading amount and, consequently, adsorption capacity compared to the MOF loading during electrospinning.
- 20 April 2020
- Published by Wiley in Journal of Chemical Technology & Biotechnology
- Vol. 95 (11) , 2921-2929
Nickel carbonyl formation in a fluidized bed reactor: experimental investigation and modeling
BACKGROUND: The Mond process has been used in the industry for nickel purification over a century. However, theoretical studies on this process are few and primarily based on empirical models. In this article, experimental and theoretical modeling of nickel tetracarbonyl formation through the Mond process under different conditions in a fluidized bed reactor is presented. Nickel tetracarbonyl, known primarily as nickel carbonyl gas, is formed through the reaction between nickel powder and carbon monoxide. The apparent reaction rate is modeled as a function of reaction temperature, inlet gas pressure, and carbon monoxide flow rate. Experimental results were obtained using a fluidized bed reactor. A diffusion‐kinetics and a two‐phase bubbling bed model were developed to compare with experimental results. The reactor is considered as a differential flow reactor for the theoretical modeling.RESULTS: Rate of reaction is measured in a fluidized bed and used for the verification of the studied models. The best performing model is a kinetic‐diffusion model with a rate of reaction that obeys rem = Kem([CO])n, in which Kem is a function of mass transfer as well as kinetic variables, but is primarily temperature dependent. Also, n for low‐pressure and high‐pressures regions is −1 and −3, respectively.CONCLUSIONS: The reaction rate is strongly dependent on carbon monoxide gas pressure. The models developed are rather simple yet provide significant improvement in predictions of the reaction rate compared to the existing models in the literature. © 2020 Society of Chemical Industry
- 20 April 2020
- Published by Wiley in Journal of Chemical Technology & Biotechnology
- Vol. 95 (11) , 2921-2929
Nickel carbonyl formation in a fluidized bed reactor: experimental investigation and modeling
BACKGROUND: The Mond process has been used in the industry for nickel purification over a century. However, theoretical studies on this process are few and primarily based on empirical models. In this article, experimental and theoretical modeling of nickel tetracarbonyl formation through the Mond process under different conditions in a fluidized bed reactor is presented. Nickel tetracarbonyl, known primarily as nickel carbonyl gas, is formed through the reaction between nickel powder and carbon monoxide. The apparent reaction rate is modeled as a function of reaction temperature, inlet gas pressure, and carbon monoxide flow rate. Experimental results were obtained using a fluidized bed reactor. A diffusion‐kinetics and a two‐phase bubbling bed model were developed to compare with experimental results. The reactor is considered as a differential flow reactor for the theoretical modeling.RESULTS: Rate of reaction is measured in a fluidized bed and used for the verification of the studied models. The best performing model is a kinetic‐diffusion model with a rate of reaction that obeys rem = Kem([CO])n, in which Kem is a function of mass transfer as well as kinetic variables, but is primarily temperature dependent. Also, n for low‐pressure and high‐pressures regions is −1 and −3, respectively.CONCLUSIONS: The reaction rate is strongly dependent on carbon monoxide gas pressure. The models developed are rather simple yet provide significant improvement in predictions of the reaction rate compared to the existing models in the literature. © 2020 Society of Chemical Industry
- 1 August 2017
- Published by Elsevier in Separation and Purification Technology
- Vol. 183, 181-193
Mathematical modeling of rapid temperature swing adsorption; the role of influencing parameters
- 1 August 2017
- Published by Elsevier in Separation and Purification Technology
- Vol. 183, 181-193
Mathematical modeling of rapid temperature swing adsorption; the role of influencing parameters
- 1 March 2017
- Published by Elsevier in Journal of the Taiwan Institute of Chemical Engineers
- Vol. 72, 45-52
A comparative investigation of CO2 adsorption on powder and pellet forms of MIL-101
- 1 March 2017
- Published by Elsevier in Journal of the Taiwan Institute of Chemical Engineers
- Vol. 72, 45-52
A comparative investigation of CO2 adsorption on powder and pellet forms of MIL-101
- 28 April 2016
- Published by Springer Nature in International Journal of Environmental Science and Technology
- Vol. 13 (8) , 2001-2010
Experimental study of pure and mixtures of CO2 and CH4 adsorption on modified carbon nanotubes
- 28 April 2016
- Published by Springer Nature in International Journal of Environmental Science and Technology
- Vol. 13 (8) , 2001-2010
Experimental study of pure and mixtures of CO2 and CH4 adsorption on modified carbon nanotubes
- 9 December 2015
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 6 (1) , 632-640
A metal–organic framework MIL-101 doped with metal nanoparticles (Ni & Cu) and its effect on CO2adsorption properties
In this work, Cu- and Ni-doped MIL-101 were synthesizedviaa microwave irradiation technique and used as adsorbents for CO2adsorption. The loading of MNPs in MIL-101 showed a beneficial effect on the adsorption capacity and cyclability.
- 9 December 2015
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 6 (1) , 632-640
A metal–organic framework MIL-101 doped with metal nanoparticles (Ni & Cu) and its effect on CO2adsorption properties
In this work, Cu- and Ni-doped MIL-101 were synthesizedviaa microwave irradiation technique and used as adsorbents for CO2adsorption. The loading of MNPs in MIL-101 showed a beneficial effect on the adsorption capacity and cyclability.
- Top Cited Papers
- 29 November 2005
- Published by Wiley in Chemical Engineering & Technology
- Vol. 28 (12) , 1525-1528
Oil Spill Cleanup from Sea Water by Sorbent Materials
Three sorbents were compared in order to determine their potential for oil spill cleanup. Polypropylene nonwoven web, rice hull, and bagasse with two different particle sizes were evaluated in terms of oil sorption capacities and oil recovery efficiencies. Polypropylene can sorb almost 7 to 9 times its weight from different oils. Bagasse, 18 to 45 mesh size, follows polypropylene as the second sorbent in oil spill cleanup. Bagasse, 14 to 18 mesh size, and rice hull have comparable oil sorption capacities, which are lower than those of the two former sorbents. It was found that oil viscosity plays an important role in oil sorption by sorbents. All adsorbents used in this work could remove the oil from the surface of the water preferentially.
- 29 November 2005
- Published by Wiley in Chemical Engineering & Technology
- Vol. 28 (12) , 1525-1528
Top Cited PapersOil Spill Cleanup from Sea Water by Sorbent Materials
Three sorbents were compared in order to determine their potential for oil spill cleanup. Polypropylene nonwoven web, rice hull, and bagasse with two different particle sizes were evaluated in terms of oil sorption capacities and oil recovery efficiencies. Polypropylene can sorb almost 7 to 9 times its weight from different oils. Bagasse, 18 to 45 mesh size, follows polypropylene as the second sorbent in oil spill cleanup. Bagasse, 14 to 18 mesh size, and rice hull have comparable oil sorption capacities, which are lower than those of the two former sorbents. It was found that oil viscosity plays an important role in oil sorption by sorbents. All adsorbents used in this work could remove the oil from the surface of the water preferentially.