Andreea Hadarig
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Andreea Hadarig has a total of 31 co-authors. Here are the top co-authors by number of shared publications:
- Fernando Las-Heras
University of Oviedo
13 shared publications George Hotopan
Area de Teoria de la Señal y Comunicaciones, Universidad de Oviedo, Gijón, Spain
7 shared publicationsRene Camblor
Area de Teoria de la Señal y Comunicaciones, Universidad de Oviedo, Gijón, Spain
7 shared publicationsSamuel Ver Hoeye
Area de Teoria de la Señal y Comunicaciones, Universidad de Oviedo, Gijón, Spain
7 shared publicationsMiguel Fernandez
Area de Teoria de la Señal y Comunicaciones, Universidad de Oviedo, Gijón, Spain
6 shared publicationsCarlos Vazquez
Area de Teoria de la Señal y Comunicaciones, Universidad de Oviedo, Gijón, Spain
5 shared publications
Latest Publications
- 1 September 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 510-513
Millimetre wave transmitter based on a few-layer graphene frequency multiplier
In this work, a millimetre/submillimetre wave transmitter prototype integrating a graphene based frequency multiplier and a diagonal horn antenna is presented. With a driving signal in the WR-28 frequency band (26.5-40 GHz), an output signal in the WR-3 frequency band (220-330 GHz) is generated and radiated. A prototype has been manufactured using high precision 3D printing techniques. The performance with multiplication orders 5, 7 and 9 has been compared, obtaining maximum power levels of about -45 dBm, measured at a distance of 250 mm. Measured radiation patterns are also presented.
- 1 September 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 510-513
Millimetre wave transmitter based on a few-layer graphene frequency multiplier
In this work, a millimetre/submillimetre wave transmitter prototype integrating a graphene based frequency multiplier and a diagonal horn antenna is presented. With a driving signal in the WR-28 frequency band (26.5-40 GHz), an output signal in the WR-3 frequency band (220-330 GHz) is generated and radiated. A prototype has been manufactured using high precision 3D printing techniques. The performance with multiplication orders 5, 7 and 9 has been compared, obtaining maximum power levels of about -45 dBm, measured at a distance of 250 mm. Measured radiation patterns are also presented.
- 1 May 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
Millimetre wave textile integrated waveguide beamforming antenna for radar applications
In this work, a fully Textile Integrated Waveguide (TIW) beamforming antenna for its use in a radar system operating at 77 GHz is presented. The TIW beamforming antenna is based on a Substrate Integrated Waveguide (SIW) slot antenna array and it is designed to be manufactured completely with conductive and non-conductive threads using industrial textile machinery, avoiding subsequent sewing and adhesive processes for its integration in wearable or comformable systems. The antenna performs beam tilting from 11 to 23 degrees in the H-plane while sweeping the frequency from 70 GHz to 77 GHz. Firstly, a design of the equivalent SIW beamforming antenna structure is simulated and optimized and then, the translation into a fully woven TIW beamforming antenna structure is presented. The proposed TIW beamforming antenna design is provided with a TIW to WR10 standard rectangular waveguide transition for its experimental validation.
- 1 May 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
Millimetre wave textile integrated waveguide beamforming antenna for radar applications
In this work, a fully Textile Integrated Waveguide (TIW) beamforming antenna for its use in a radar system operating at 77 GHz is presented. The TIW beamforming antenna is based on a Substrate Integrated Waveguide (SIW) slot antenna array and it is designed to be manufactured completely with conductive and non-conductive threads using industrial textile machinery, avoiding subsequent sewing and adhesive processes for its integration in wearable or comformable systems. The antenna performs beam tilting from 11 to 23 degrees in the H-plane while sweeping the frequency from 70 GHz to 77 GHz. Firstly, a design of the equivalent SIW beamforming antenna structure is simulated and optimized and then, the translation into a fully woven TIW beamforming antenna structure is presented. The proposed TIW beamforming antenna design is provided with a TIW to WR10 standard rectangular waveguide transition for its experimental validation.
- Open Access
- 1 May 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
3D printed millimeter wave receiver integrating a graphene subharmonic mixer and a diagonal horn antenna
This work presents a millimeter/submillimeter wave frequency receiver integrating a graphene subharmonic mixer and a diagonal horn antenna. The device receives the RF signal through the diagonal horn antenna directly connected to the WR-3 input of the mixer. The desired frequency mixing performance is obtained using the non-linear behavior of a few-layer graphene film placed on a microstrip line gap. Using the internally generated 6 th , 8 th and 10 th harmonic components of the input signal provided by the WR-28 standard waveguide in the 26-40 GHz the downconversion operation of the RF signal to a 300 MHz intermediate frequency is performed. A prototype of the receiver has been manufactured using high precision 3D printing technology. The performance of this device is characterized taking into account the behavior of the IF power in the 220-330 GHz band. Measured radiation patterns are also included.
- 1 May 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
Open Access3D printed millimeter wave receiver integrating a graphene subharmonic mixer and a diagonal horn antenna
This work presents a millimeter/submillimeter wave frequency receiver integrating a graphene subharmonic mixer and a diagonal horn antenna. The device receives the RF signal through the diagonal horn antenna directly connected to the WR-3 input of the mixer. The desired frequency mixing performance is obtained using the non-linear behavior of a few-layer graphene film placed on a microstrip line gap. Using the internally generated 6 th , 8 th and 10 th harmonic components of the input signal provided by the WR-28 standard waveguide in the 26-40 GHz the downconversion operation of the RF signal to a 300 MHz intermediate frequency is performed. A prototype of the receiver has been manufactured using high precision 3D printing technology. The performance of this device is characterized taking into account the behavior of the IF power in the 220-330 GHz band. Measured radiation patterns are also included.
- 1 May 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
Millimetre wave receiver based on a few-layer graphene WR-5 band subharmonic mixer
In this work, a millimetre wave receiver prototype integrating a graphene based subharmonic mixer and a diagonal horn antenna is presented. The block receives a millimetre wave signal in the WR-5 frequency band (140-220 GHz), which is downconverted using a high-order harmonic component of the local oscillator signal, in the WR-28 frequency band (26.5-40 GHz), producing an IF output at 300 MHz. A prototype has been manufactured using high precision 3D printing techniques. The performance for subharmonic orders 6, 8 and 10 has been evaluated through preliminary measurements in the neighbouring WR-3 frequency band. Measured radiation patterns are also presented.
- 1 May 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
Millimetre wave receiver based on a few-layer graphene WR-5 band subharmonic mixer
In this work, a millimetre wave receiver prototype integrating a graphene based subharmonic mixer and a diagonal horn antenna is presented. The block receives a millimetre wave signal in the WR-5 frequency band (140-220 GHz), which is downconverted using a high-order harmonic component of the local oscillator signal, in the WR-28 frequency band (26.5-40 GHz), producing an IF output at 300 MHz. A prototype has been manufactured using high precision 3D printing techniques. The performance for subharmonic orders 6, 8 and 10 has been evaluated through preliminary measurements in the neighbouring WR-3 frequency band. Measured radiation patterns are also presented.
- 26 February 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 63 (4) , 1361-1369
High-Order Subharmonic Millimeter-Wave Mixer Based on Few-Layer Graphene
A millimeter-wave subharmonic-mixer topology based on a few-layer graphene component has been designed, manufactured, and experimentally characterized. The circuit has been conceived to perform the up/downconversion of a signal in the WR-3 band, between 220-330 GHz, using a high-order harmonic component of the input signal in the WR-28 band, between 26.5-40 GHz, as a local oscillator. The manufactured prototype has been characterized in both upconversion and downconversion, for the subharmonic orders between 5-14, obtaining a peak conversion gain value over -65 dB. The theoretically predicted capability of graphene to produce high-order intermodulation products at millimeter-wave frequencies, with a slowly decaying amplitude pattern, has been experimentally verified.
- 26 February 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 63 (4) , 1361-1369
High-Order Subharmonic Millimeter-Wave Mixer Based on Few-Layer Graphene
A millimeter-wave subharmonic-mixer topology based on a few-layer graphene component has been designed, manufactured, and experimentally characterized. The circuit has been conceived to perform the up/downconversion of a signal in the WR-3 band, between 220-330 GHz, using a high-order harmonic component of the input signal in the WR-28 band, between 26.5-40 GHz, as a local oscillator. The manufactured prototype has been characterized in both upconversion and downconversion, for the subharmonic orders between 5-14, obtaining a peak conversion gain value over -65 dB. The theoretically predicted capability of graphene to produce high-order intermodulation products at millimeter-wave frequencies, with a slowly decaying amplitude pattern, has been experimentally verified.
- Open Access
- 20 September 2014
- Published by Springer Nature in Applied Physics A
- Vol. 118 (1) , 83-89
Experimental analysis of the high-order harmonic components generation in few-layer graphene
- 20 September 2014
- Published by Springer Nature in Applied Physics A
- Vol. 118 (1) , 83-89
Open AccessExperimental analysis of the high-order harmonic components generation in few-layer graphene
- 1 August 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Millimetre wave subharmonic mixer based on graphene
An eighth order subharmonically pumped mixer for the implementation of a millimetre wave imaging system is presented. The block receives the RF signal in the WR-3 band, between 220 and 330 GHz, and downconverts it to a 300 MHz intermediate frequency, using the internally generated eighth harmonic component of an input signal in the WR-28 frequency band, between 26.5 and 40 GHz. The subharmonic mixing operation is performed taking advantage of the non-linearity of a few layer graphene component, integrated in a microstrip structure.
- 1 August 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Millimetre wave subharmonic mixer based on graphene
An eighth order subharmonically pumped mixer for the implementation of a millimetre wave imaging system is presented. The block receives the RF signal in the WR-3 band, between 220 and 330 GHz, and downconverts it to a 300 MHz intermediate frequency, using the internally generated eighth harmonic component of an input signal in the WR-28 frequency band, between 26.5 and 40 GHz. The subharmonic mixing operation is performed taking advantage of the non-linearity of a few layer graphene component, integrated in a microstrip structure.
- 1 August 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 753-756
Frequency scanning slotted waveguide in the sub-millimeter wave band
In this work, a waveguide slotted antenna array working in the sub-millimeter wave band is presented. The antenna performs beam tilting from 68 to 89 degrees in the H-plane while sweeping the frequency from 240 GHz to 310 GHz. Sixteen rectangular slots have been cut in the wide surface of a standard WR-3 brass metal rectangular waveguide to obtain the desired behavior. The antenna has been fabricated combining laser and mechanical prototyping machinery. Experimental results showing the main waveguide slotted antenna array characteristics are also presented.
- 1 August 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 753-756
Frequency scanning slotted waveguide in the sub-millimeter wave band
In this work, a waveguide slotted antenna array working in the sub-millimeter wave band is presented. The antenna performs beam tilting from 68 to 89 degrees in the H-plane while sweeping the frequency from 240 GHz to 310 GHz. Sixteen rectangular slots have been cut in the wide surface of a standard WR-3 brass metal rectangular waveguide to obtain the desired behavior. The antenna has been fabricated combining laser and mechanical prototyping machinery. Experimental results showing the main waveguide slotted antenna array characteristics are also presented.
- 1 August 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 675-678
Millimetre wave imaging system for the detection of hidden elements in artwork
In this work, a millimetre/sub-millimetre wave imaging system for the analysis, characterisation and detection of hidden elements in artwork is presented. The practical implementation of the system relies on a novel generation of purpose developed frequency multiplier and mixer topologies, based on graphene non-linear devices. The proposed set-up will be experimentally validated by scanning a model painting, in order to practically illustrate the imaging capabilities of the system.
- 1 August 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 675-678
Millimetre wave imaging system for the detection of hidden elements in artwork
In this work, a millimetre/sub-millimetre wave imaging system for the analysis, characterisation and detection of hidden elements in artwork is presented. The practical implementation of the system relies on a novel generation of purpose developed frequency multiplier and mixer topologies, based on graphene non-linear devices. The proposed set-up will be experimentally validated by scanning a model painting, in order to practically illustrate the imaging capabilities of the system.
- 1 August 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 750-752
Sub-millimeter wave imaging system based on frequency scanning antenna
A novel sub-millimeter wave imaging system using a frequency scanning antenna, a diagonal horn and two biconvex lenses is presented in this work. The system has been designed to operate from 270 GHz to 330 GHz. The topology has been validated through simulations and measurements. Images obtained with the proposed system and other topologies are presented and discussed.
- 1 August 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 750-752
Sub-millimeter wave imaging system based on frequency scanning antenna
A novel sub-millimeter wave imaging system using a frequency scanning antenna, a diagonal horn and two biconvex lenses is presented in this work. The system has been designed to operate from 270 GHz to 330 GHz. The topology has been validated through simulations and measurements. Images obtained with the proposed system and other topologies are presented and discussed.