MDMelinda Darby Dyar

Melinda Darby Dyar

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Melinda Darby Dyar has a total of 361 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Overview of the MMT 60‐Day GEER Experiment on Geologic Samples at Venus Surface Conditions

    by Martha S. Gilmore, Alison R. Santos, Jeffrey Balcerski, Laura B. Breitenfeld, M. Darby Dyar, Daniel Gerges, Joern Helbert, Ian Henry, Noam Izenberg, Jennifer M. Jackson, et al.

    Laboratory experiments on the behavior of rock and mineral samples under Venus conditions can yield a better understanding of gas‐solid chemical weathering on the Venus surface. The Glenn Extreme Environments Rig (GEER) vessel can maintain Venus surface temperature, pressure and a nine‐gas atmosphere for months. We provide an overview of the GEER Test Project Marty's Minerals Test (MMT), which ran for 60 days at 460°C, 93 bars under a 9‐ component Venus‐relevant gas mixture. This experiment included over 90 compositionally unique chips and powders of natural samples selected to explore the pathways and relative rates of alteration of a broad range of mineral and rock types. Temperature, pressure, and gas (CO 2 , N 2 , SO 2 , OCS) composition were monitored over the run. Rapid SO 2 depletion from the vessel gas phase occurred throughout the test, indicating sequestration of SO 2 via gas‐solid reactions. A significant sink for SO 2 is the formation of iron oxide and nickel sulfide coatings on some chamber parts, which was compensated by multiple SO 2 gas injections during the run. Initial results for selected samples include the formation of secondary minerals at sample surfaces (e.g., on Na 2 CO 3 , natrite) and complete alteration of other samples (e.g., FeS, troilite) to oxides and sulfides. Some powdered samples consolidated to form hardened layers or chips. These observations show that some mineral phases are chemically and/or physically unstable over the timescale of the run. This test confirms that the GEER is a critical asset and reference point to support the study of gas‐solid interactions at Venus conditions.


  • Different crystallization events of Li-bearing pegmatitic tourmaline from San Piero in Campo, Elba Island, Italy

    by Andreas Ertl, Frederico Pezzotta, John M. Hughes, Hans-Peter Meyer, Thomas Ludwig, M. Darby Dyar, Gerald Giester, George R. Rossman

    To learn more about the growth zones of distinctly zoned tourmalines from the well-studied Rosina aplite–pegmatite dike of the Monte Capanne pluton near San Piero in Campo, Elba Island, Italy, four tourmaline crystals rooted in the pegmatitic rock and developed into three different small cavities, as well as one additional crystal growing frozen in the pegmatitic rock, were chemically characterized. The light element contents and the unit cell parameters of the four samples were also determined. Black Fe2+-rich tourmaline, grown directly within the pegmatite, with unit cell parameters a = 15.97–15.98 Å, c = 7.15–7.16 Å, can be assigned to schorl and fluor-schorl with only 4 % Fe3+. The Fe content decreases during crystallization, whereas Mn and F contents increase (up to 8 wt % MnO and 1.4 wt % F), forming a growth sector of olive-green colour. Such olive-green tourmaline exhibits unit cell parameters of a = 15.87–15.94 Å, c = 7.12–7.14 Å and can be assigned to fluor-tsilaisite and Mn2+-rich fluor-elbaite. Later, the Mn content decreases and the Al and Li contents increase (up to 44 wt % Al2O3 and 1.7 wt % Li2O). These zones can have Ga and Pb contents of up to ~1100 and ~500 ppm, respectively. The colour of such tourmaline can be pale olive-green, pale pink, or colourless. These crystal zones have unit cell parameters of a = 15.78–15.82 Å, c = 7.08–7.10 Å, and can be assigned to fluor-elbaite, elbaite, rossmanite, and darrellhenryite. In the final stage of tourmaline crystallization, the F content in the investigated crystal terminations can drop down to 0.1 wt % F, while the (Fe + Mn) content increases. Usually, these terminations can be assigned to elbaite (a = 15.79–15.83 Å, c = 7.08–7.10 Å). When comparing the F content and the X-site charge (Na, Ca), all zones grown in the pegmatite pocket, except for the termination, show a strong positive correlation for each crystal examined. This observation is interpreted as evidence that the caps of the tourmaline crystals in the pegmatite pockets formed during a different event than the previously grown crystals.

  • Open Access

    Spectroscopy of the Hamburg Meteorite, Michigan H4

    by M. Darby Dyar, Laura B. Breitenfeld, Melissa D. Lane, Timothy Glotch, Roger Clark, Neil Pearson, Elizabeth C. Sklute, Molly C. McCanta, Amanda J. Hendrix, Brandon Weller, et al.

    Spectroscopic studies of the Hamburg (Michigan H4) meteorite using visible–near-infrared (VNIR), mid-infrared (MIR), Raman, and Mössbauer data reproduce the results of more conventional laboratory measurements of petrology and geochemistry. This combination provides general information on the mineral modes of silicates, although spectroscopy was performed on different splits of this meteorite, and varying results may be explained by heterogeneity that is typical of ordinary chondrites. Raman also detects small features assigned to first-order D and G carbon bands, while Mössbauer data show the presence of Fe oxides and carbides. The electron microprobe (EMPA) composition of olivine in this meteorite is accurately measured to be Fo 81.3 , while MIR and Raman closely agree with Fo 80 and Fo 82 , respectively, and Mössbauer, at Fo 60 − Fo 70 , is in the ballpark. Similarly, P. R. Heck et al. report pyroxenes with compositions of Fs 16 Wo 1 , while Raman suggests a somewhat similar composition of Fs 28 Wo 0 . Both VNIR and MIR detect the presence of small amounts of feldspar, while EMPA identifies its composition as An 14 Ab 8 Or 5 . VNIR data were matched to spectral libraries of meteorite and asteroid data and shown to closely match other L and H meteorites. The best spectral matches to the Michigan H4 meteorite are to asteroid classes L/H/LL/URE, EH/EL/AUB, and CO/CV from M. D. Dyar et al.; objects in this group are intermediate in semimajor axis lengths for their orbits. The results highlight the strengths and weaknesses of each technique and show their collective strength when applied together to a single meteorite sample.

  • Open Access

    Overview of the MMT 60-day GEER Experiment on Geologic Samples at Venus Surface Conditions

    by Martha S. Gilmore, Alison R. Santos, Jeffrey A. Balcerski, Laura B. Breitenfeld, M. Darby Dyar, Daniel Gerges, Joern Helbert, Ian Henry, Noam Izenberg, Jennifer M. Jackson, et al.

    Laboratory experiments on the behavior of rock and mineral samples under Venus conditions can yield a better understanding of gas-solid chemical weathering. The Glenn Extreme Environments Rig (GEER) vessel can maintain Venus surface temperature, pressure and a nine-gas atmosphere for months. Here, we provide an overview of the GEER Test Project Marty’s Minerals Test (MMT), which ran for 60 days at 460°C, 93 bars under a 9 component Venus-relevant gas mixture. This experiment includes over 90 compositionally unique chips and powders of natural samples, selected to explore the pathways and relative rates of alteration of a broad range of mineral and rock types. Target temperature, pressure, and gas (CO2, N2, SO2, OCS) composition were monitored over the run. Rapid SO2 depletion from the vessel gas phase occurred throughout the test indicating sequestration of SO2 gas-solid reactions. A significant sink for SO2 is the formation of iron oxide and Ni sulfide coatings on some chamber parts that was compensated by multiple SO2 gas injections during the run. Initial results for selected samples include the formation of secondary minerals at sample surfaces (e.g., on Na2CO3, natrite) and complete alteration of other samples (e.g., FeS, troilite) to oxide and sulfides. Some powdered samples consolidated to form hardened layers or chips. These observations show that some mineral phases are chemically and/or physically unstable over the timescale of the run. This test confirms that GEER is a critical asset and reference point to support the study of gas-solid interactions on the surface of Venus.


  • Open Access

    The Venus Emissivity Mapper Emulator 2.0: a NIR camera system for Venus analogue measurements in the field and in the laboratory

    by Stephen P. Garland, Solmaz Adeli, Nils Müller, Christian Althaus, Melinda Darby Dyar, Suzanne E. Smrekar, Daniel C. Nunes, Akin Domac, Giulia Alemanno, Océane Barraud, et al.

    IntroductionSeveral major missions to Venus are planned for launch in the early 2030’s, amongst them are NASA’s VERITAS [1] and ESA’s EnVision [2] missions. The VERITAS mission will launch with the Venus Emissivity Mapper (VEM) instrument [3] designed to measure the emissivity of Venus’s surface and atmosphere. Despite being our closest neighbor, we know surprisingly little about Venus, partly due to its optically dense atmosphere of CO2 with clouds of H2SO4, making direct surface observations challenging. The VEM instrument will overcome this challenge by exploiting 6 narrow bands of higher atmospheric transmission in the near infrared (NIR) between 0.86 and 1.18 µm, with the goal of distinguishing felsic from mafic rock types and contributing to the detection of recent or active volcanism [1]. Additional bands observing the cloud and atmosphere composition can be used to correct for atmospheric effects and distortion. In preparation for the mission, extensive work is being carried out on the spectroscopy of Venus analogs in the laboratory, as well as at Venus analog field sites. In this framework the VERITAS Science Team undertook a 2-week field campaign at analog sites in Iceland in August 2023 [4]. As part of this field campaign, of which the major goal was to ground truth radar measurements with detailed lidar scans [4], a team was dedicated to investigating the NIR spectral properties of the sites. To this end an emulator of VEM was constructed for field work [5,6] with the goal of obtaining VEM-like data to train scientists and to investigate the response of various surfaces in the NIR from reflectance and emission spectra collected both in the field, including from hot lavas, and in the lab.The camera setupA top view of the camera system is shown in Figure 1. The system is based around a cooled NIR InGaAs OWL 1280 Camera from the company Raptor Photonics, sensitive in the range 0.6 to 1.7µm. A frame grabber (Pleora Technologies, iPort CL-U3) was used to read out images from the camera via a Camera Link interface. In front of this, we positioned a filter wheel containing 6 commercially available 1” bandpass filters from Thorlabs with central wavelengths closely matching those chosen for VEM: 860nm, 910nm, 990nnm, 1030nm, 1100nm, 1200nm. Between the detector and the filter wheel a C-mount 25mm SWIR lens was fitted. The detector, frame grabber and motor controller unit were accommodated inside a dustproof casing with two fans for cooling of the camera housing, which requires heat dissipation due to the inbuilt TEC for detector cooling. The camera system can be mounted on a tripod and packed into a transport box. The camera was calibrated using an integration sphere with halogen light sources, allowing radiance values to be calculated for measurements through each filter [5].Figure 1. The VEMulator 2.0 camera system.Field and laboratory measurementsThe VEMulator2.0 camera system was originally intended for measuring reflectance spectra in the NIR as part of the VERITAS Science Team 2023 field campaign to Venus analog sites in Iceland. By chance, during the field campaign, a volcanic eruption occurred on the Reykjanes peninsula. By the time the team arrived at the site, the eruption was no longer active, however the crater region still exhibited hot spots up to around 400 °C. VEMulator2.0 measurements were made at nighttime with low ambient light levels with a simultaneous measurement using a FLIR thermal infrared camera to estimate the temperature (Figure 2). Initial calculations of emissivity from a brighter hot spot (210 °C from the FLIR measurement) were not consistent with an independent laboratory-measured spectrum of basalt from the eruption site. The radiance values are more consistent with a basalt in the temperature range of 240°C to 280°C. In fact, the discrepancy is more likely due to the presence of light-toned deposits observed in context photos in this region, which likely have lower emissivity values. This contribution analyzes this problem in more depth, with the support of reference measurements performed at the Planetary Spectroscopy Laboratory [7], by examining different contributions to the observed spectra, such as emission from material at multiple temperatures, and compositional inhomogeneities.Figure 2. a). Raw pixel values from a region of an image taken with VEMu2.0 using the 860 nm filter. The red square shows a region of interest. b). The same field of view with a FLIR thermal infrared camera showing calibrated temperatures. The red square shows the same regions of interest. From [5].Acknowledgments: S. P. Garland, S. Adeli, N. Müller, A. Domac received funding from the European Union's Horizon 2020 research and innovation programme under grant agreement No 871149. References[1] Smrekar, S. (2022) IEEE Aerospace Conf. [2] Ghail, R. C. et al. (2012) Exp. Astron., vol. 33, no. 2, pp. 337–363 [3] Helbert, J., et al. (2022) SPIE. [4] Nunes, D. et al. (2024) LPSC 55. [5] Garland, S. et al. (2024) SPIE. [6] Adeli, S. et al. (2024) LPI Contributions, vol. 3040, p. 1286. [7] Helbert, J. et al. (2023) SPIE.

  • Open Access

    The Spectroscopic Properties of Phosphates and Identifying Them on Mars

    by Janice L. Bishop, Melissa D. Lane, M. Darby Dyar

    Phosphate minerals are present in multiple martian meteorites and have been detected on the surface of Mars by several rover missions and have important implications for astrobiology [1]. We initiated a study of the spectral properties of phosphate minerals two decades ago [2] to support identification of phosphates on Mars using Thermal-IR (TIR), Visible/Near-Infrared (VNIR) and Mössbauer spectroscopy and have been updating our collections [3, 4, 5]. Phosphate minerals form in a wide variety of structures built around PO4 tetrahedra, similar to the mineral structures containing SiO4 and SO4 tetrahedra and many of these could be present on Mars. Nanophase materials characterized at Gale crater may also contain phosphates [6].Primary phosphates that crystallize from a fluid include apatite (Ca5(PO4)3OH) and triphylite (LiFe2+PO4), while strengite (FePO4•2H2O) and vivianite (Fe2+Fe2+2(PO4)2•8H2O) are secondary phosphates that form in low temperatures aqueous environments. Whitlockite (Ca9(MgFe)(PO4)6PO3OH) can be found in chondrites within meteorites. TIR emissivity spectra in the mid-IR region (Figure 1-A, 200-1500 cm-1) are dominated by the vibrational modes of the (PO4)3- tetrahedra including stretching vibrations near 1000-1200 cm-1 and bending vibrations near 600-700 cm-1 [5, 7].Phosphates exhibit multiple spectral features in the VNIR region (Figure 1-B, 0.3-5 µm) due to vibrations of H2O, OH, and PO4 groups in the structure as well as excitation absorptions due to Fe [e.g., 4]. Fe bands typically occur near 0.6-1.2 µm, OH bands near 1.45, 2.2 and 2.8 µm, H2O bands near 1.45, 1.95, and 2.9-3 µm, and phosphate bands near 4.5-5 µm. Kulanite (BaFe22+Al2(PO4)3(OH)3), childrenite-eosphorite (Fe2+,Mn2+)AlPO4(OH)2·H2O), and gormanite (Fe32+Al4(PO4)4(OH)6·2H2O) are OH-bearing phosphates and their spectra have strong OH bands near 1.44-1.50, 2.17-2.47, and 2.76-2.87 µm, respectively due to an OH stretching overtone, an OH stretch plus bend combination band, and an OH fundamental stretching vibration. Apatite also includes OH and its spectra include a fundamental stretching vibration at 2.83 µm as well as a triplet near 3.37-3.48 µm and a doublet at 3.98 and 4.02 µm.Mössbauer spectroscopy of ferric and ferrous phosphates provide a range of isomer shifts and quadrupole splitting values that can be used to identify specific minerals [3]. The Mössbauer parameters, TIR spectra, and extended visible region spectra collected by the Mars Exploration Rovers were used to constrain potential ferric phosphate minerals present along with sulfates at Paso Robles in Gusev Crater [8]. We are currently investigating the presence of phosphates at Gusev and Jezero Craters, especially Ca- and Fe-bearing phosphates including vivianite [9].References: [1] Hausrath et al. (2024) Minerals, 14, 591. [2] Lane et al. (2007) LPSC, #2210. [3] Dyar et al. (2014) American Miner., 99, 914–942. [4] Bishop (2019) Chapter 4, in Remote Compositional Analysis ... (Cambridge) 68-101. [5] Lane & Bishop (2019) Chapter 3, in Remote Compositional Analysis ... (Cambridge) 42-67. [6] Rampe et al. (2016) American Miner., 101, 678-689. [7] Stutman et al. (1965) Trans. NY Academy Sci., 27, 669-675. [8] Lane et al. (2008) American Miner., 93, 728-739. [9] Kizovski et al. (2024) LPSC, #2615.


  • Open Access

    Geochemistry by Laser‐Induced Breakdown Spectroscopy on the Moon: Accuracy, Detection Limits, and Realistic Constraints on Interpretations

    by M. D. Dyar, C. R. Ytsma, K. Lepore

    After its successful implementation on the surface of Mars, laser‐induced breakdown spectroscopy (LIBS) is likely to be employed on a diverse array of other solid bodies in our Solar System. Here we address the accuracy and quantification limits of LIBS under the vacuum conditions found on the Moon relative to what is known about its geochemistry. The interplay among accuracy as represented by root mean‐squared errors (RMSE), the median concentration, and quantification limits (LOQ) of LIBS analyses for each of 69 elements is evaluated. This comparison shows that several key elements in lunar geochemistry cannot be well‐studied with LIBS, including K2O, S, Rb, Br, and C. Conversely, highly accurate analyses of SiO2, CaO, and many minor and trace elements such as Mn, Yb, and Zn are possible under conditions found on the Moon. Use of LIBS must always be considered in the context of the geochemistry and geology of the target materials.


  • Open Access

    Testing the Bus–DeMeo Asteroid Taxonomy Using Meteorite Spectra

    by Thomas H. Burbine, Iman Khanani, Deepika Kumawat, Ahlay Hussain, Sydney M. Wallace, M. Darby Dyar

    The most widely used method to spectrally classify asteroids is the Bus–DeMeo taxonomy. To test how well the Bus–DeMeo taxonomy groups asteroids on the basis of their mineralogy, we have classified ∼1500 meteorite spectra using this Bus–DeMeo system. Some asteroid classes group together meteorites with similar compositions better than others. Howardite, eucrite, and diogenite spectra tend to be classified as V-types, while ordinary chondrite spectra tend to be classified as S-complex or Q-type bodies. The relatively featureless D- and X-types tend to be dominated by CM carbonaceous chondrites but with a substantial number of matches also with iron meteorites. The large proportion of CM chondrite matches for the D- and X-classes is most likely due to the large number of CM chondrite spectra and the rarity of spectra of more fragile carbonaceous chondrites in our data set. A number of relatively featureless asteroid classes like the C-, B-, L-, and Xc-types group meteorite types together with a wide variety of mineralogies and thermal histories. Visual albedos are vital for distinguishing between many of these assemblages. The Bus–DeMeo taxonomy does have trouble classifying olivine-dominated meteorites that do not have red-sloped spectra because this type of spectrum is rare among asteroids. For many asteroid classes, care must be used when making mineralogical interpretations based solely on spectral type.


  • Open Access

    Reflectance Spectroscopy of 27 Fine-particulate Mineral Samples from Far-ultraviolet through Mid-infrared (0.12–20 μm)

    by Melissa D. Lane, Edward A. Cloutis, Roger N. Clark, M. Darby Dyar, Joern Helbert, Amanda R. Hendrix, Gregory Holsclaw, Alessandro Maturilli, Neil Pearson, Mikki Osterloo, et al.

    This paper presents far-ultraviolet through mid-infrared (0.12–20 μm) reflectance spectra of 27 fine-particulate (μm) terrestrial mineral samples, providing continuous spectra that cover an unusually broad spectral range and are of unusually fine particle size relative to most existing spectral libraries. These spectra of common geologic materials are useful for future applications that study the dust on various planetary bodies. Reflectance spectra were acquired of the samples at multiple laboratories at multiple wavelengths. All of the spectra were compared to one another to observe the general, common spectral characteristics (e.g., slope, band shape, and band depth), and the best segments of the spectra representing the mineral reflectance were scaled and spliced together to form a “Frankenspectrum” for each mineral that best represents the full wavelength range of far-ultraviolet, visible, near-infrared, and middle-infrared wavelengths. These scaled and spliced Frankenspectra, as well as the entire set of individual “original” reflectance spectra from each laboratory, are available in the Planetary Data System Geosciences Node.


  • Open Access

    Compositional Characterization of Glassy Volcanic Material From VSWIR and MIR Spectra Using Partial Least Squares Regression Models

    by C. J. Leight, C. Ytsma, M. C. McCanta, M. D. Dyar, T. D. Glotch

    The glass phase in volcanic rocks presents a challenge to obtaining compositional data from visible and short‐wave‐infrared (VSWIR) and mid‐infrared (MIR) spectral data of remote surfaces due to its amorphous structure and variable composition. Nonetheless, glass is a common phase in volcanic materials because it forms via the rapid quench of magma and can constitute up to the entirety of a volcanic deposit. Use of partial least squares regression (PLS) to predict glass contents creates models that are insensitive to viewing geometry and sample conditions such as grain size and spectrally inactive compositional variables, enhancing the ability to detect glasses with remote sensing. PLS models are used here to predict crystallinity and oxide composition of samples from VSWIR and MIR spectral data using training spectra from natural volcanic rocks and geologically relevant synthetic samples. Three spectral resolutions of VSWIR and MIR spectra (1, 10, and 100 nm/band, and 1.9, 19, and 190 cm−1/band, respectively) were tested to assess the effects of collection configuration on different spectrometers. PLS models trained on 1 nm and 1.9 cm−1 data sets have the lowest uncertainties of glass modal abundance for VSWIR and MIR, respectively. MIR models predicting sample wt. % SiO2 and FeO, and VSWIR models of wt. % FeO provide accurate estimates (e.g., RMSE‐P of 3.4 wt. % FeO) at all spectral resolutions. Results are based on training data sets skewed to mafic compositions, which affects model accuracies.