Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Geordie Drummond McBain has a total of 35 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Bubble Nucleation Pulse-Width in Thermal Inkjet Actuators

    by S. G. Mallinson, G. D. McBain, G. D. Horrocks, A. J. North, C. S. Lakshmi, T. H. K. Starke, G. W. Lowe, C. S. Barton, S. Myers

    Thermal inkjet actuators operate by passing a current through an electrical resistor, the heater, in contact with a working liquid such as ink. This heats the liquid rapidly (dT/dt≈108−109 K/s), and once the liquid temperature exceeds the superheat limit, it flash-boils. The resultant high temperature (≈300 °C) and pressure (≈10 MPa) bubble expands, forcing the ink through a nozzle, forming a droplet which then travels through the print gap until it strikes the media. Here, we discuss the bubble nucleation criterion for thermal inkjet technology, using numerical and analytical models. The results from the different models, and data from bubble visualization and droplet weight experiments, are within approximately 10% of each other. The experimental data provide a useful benchmark for comparison against other theoretical models. The newly derived analytical model provides a simple method for the thermal inkjet designer to estimate the bubble nucleation pulse-width and the energy required for nucleation.


  • Effectiveness of the dispersed-phase continuum model for investigating the airflow in the print gap of inkjet printers

    by A. F. V. de A. Aquino, S. G. Mallinson, G. D. McBain, G. D. Horrocks, C. M. de Silva, T. J. Barber

    To investigate the effectiveness of the dispersed-phase continuum (DPC) approximation to model the airflow in the print gap of inkjet printers, three-dimensional simulations using the DPC model were compared against those using the classic particle-in-cell (P-in-C) approach. The DPC approximation, due to the separation of time scales, models the dispersed phase with a momentum source that depends on a predefined temporally averaged particle number density field. The results demonstrated that the steady DPC model correlated well to the time-averaged P-in-C solution when the former's formulation accounted for the droplet deceleration. The steady DPC model requires less than 0.1% of the computational resources used by the transient P-in-C approach to compute the mean flow field. Further analyses indicated that the DPC model captured a supercritical pitchfork bifurcation, where the airflow shifted from a steady spanwise uniform regime to a standing wave regime at a critical number density. The P-in-C model computed a smooth continuous transition that characterizes an excited supercritical pitchfork bifurcation. An excellent correlation between the models was observed at print densities above the transition point, but at low number densities a certain level of discrepancy was observed. This was a result of the pseudoturbulence or spottiness induced by the local and instantaneous motion of droplets that excited the standing wave solution even at low number densities. The results, thus, demonstrated that the DPC model is effective at estimating the mean flow field and approximating the bifurcation diagram, while being simultaneously more computationally efficient than the P-in-C model.


  • Open Access

    Conjugate Heat Transfer in Thermal Inkjet Printheads

    by S. G. Mallinson, G. D. McBain, B. R. Brown

    The mass of individual droplets ejected from a thermal inkjet printhead increases with increasing local temperature near the ejector nozzles. The amount of ink deposited on the page and so the printed image density depends on the droplet mass. Thus, printhead temperature nonuniformity results in printed image density variations that can be unacceptable to the end users of the printed output. Such temperature variations arise from a combination of the ink fluid flow and the heat transfer in both the ink and the solid components in the printhead. Conjugate heat transfer (CHT) in thermal inkjet printheads is investigated here using validated numerical simulations. A typical thermal inkjet printhead is considered here for the first time, with cold ink drawn through the solid structural components by the ejector nozzle refill. The effect of the width of the feedhole above the printhead chip on the temperature field within the chip is analyzed. Validation of the simulation model required the derivation of novel analytical solutions for the relatively simple problems of fully developed forced convection in a differentially heated planar channel and conduction against convection in plug flow. The results from numerical simulations of these two problems are found to compare well with the newly derived analytical solutions. CHT in flow over a backward-facing step with a heated downstream wall was also simulated as part of the validation process, and good agreement was observed with earlier numerical studies. For the main part of the study, it was found that increasing the width of the feedhole reduces the gradients in temperature on the surface of the printhead chip, thus reducing temperature-related printing defects.


  • The Effect of Humidity on Natural Convection in Vertical Air Filled Cavities

    by Geordie D. McBain, Jonathan A. Harris, D.J. Close, Harry Suehrcke

    The Australian Research Council is funding a project investigating natural convection in cavities filled with unsaturated water vapour-air mixtures. A companion paper (McBain et al., 1996) describes the design of the experimental apparatus to be used in the project. Previous studies dealt with the case where the gas-vapour mixture in a cavity is saturated. This paper describes preliminary numerical analyses for a cavity with vertical isothermal and isohumid walls, where the vapour pressure on one or both of the surfaces is less than saturation. Following comparison of the results from the code for a single phase component with a bench mark result, the saturated case is solved for two situations viz. where condensation occurs in the fluid and where the fluid is supersaturated. Finally, a number of cases are shown where the states of the hot and cold walls ensure unsaturated mixtures within the cavity. Depending on these states, the buoyancy ratio, N, which compares the temperature and concentration buoyancy forces, can be positive or negative. The result of the runs is that the overall energy transfer rates can be up to two orders of magnitude higher than for the heat transfer only case with the same wall temperatures, or reversed with net energy transfer from cold to hot wall.

  • Design of Experimental Apparatus for the Measurement of Overall Heat Transfer Rates for Internal Natural Convection in Gas-Vapour Mixtures

    by Geordie D. McBain, D.J. Close, Harry Suehrcke, Jonathan A. Harris, M. J. Brandemuehl

    The Australian Research Council is funding a project investigating natural convection in cavities filled with unsaturated humid air. Part of the project requires that experiments be performed measuring the overall energy transfer rates between surfaces in the cavities. A major aim of the investigation is to quantify the contribution of moisture migration to the energy transfer between vertical walls. This paper describes the design of an apparatus in which steady-state, thermal and compositional buoyancy driven flows, with a wide range of Grashof numbers and buoyancy ratios, can be created, and the resulting energy transfer rates measured. The major design problem is the generation of uniform, time-invariant, unsaturated vapour pressures at arbitrarily oriented, no-slip surfaces, which are independent of the cavity flow field and the mass transfer rate. Various options are explored and the final choice, which requires at the heated wall a stirred salt solution retained behind a micro-porous hydrophobic membrane, and at the cold wall a continuously forming ice layer, is described in more detail.

  • The primitive Orr–Sommerfeld equation and its solution by finite elements

    by Geordie Drummond McBain

    The linear stability of parallel shear flows of incompressible viscous fluids is classically described by the Orr–Sommerfeld equation in the disturbance streamfunction. This fourth-order equation is obtained by eliminating the pressure from the linearized Navier–Stokes equation. Here we consider retaining the primitive velocity-pressure formulation, as is required for general multidimensional geometries for which the streamfunction is unavailable; this affords a uniform description of one-, two-, and three-dimensional flows and their perturbations. The Orr–Sommerfeld equation is here discretized using Python and scikit- fem, in classical and primitive forms with Hermite and Mini elements, respectively. The solutions for the standard test problem of plane Poiseuille flow show the primitive formulation to be simple, clear, very accurate, and better-conditioned than the classical. References

  • Investigation of the vortex instability in a two-dimensional inkjet print-zone using numerical analysis

    by A. F. V. de A. Aquino, S. G. Mallinson, G. D. McBain, G. D. Horrocks, C. M. de Silva, T. J. Barber

    A numerical model was employed to investigate the vortex instability in a two-dimensional inkjet print-zone. The simulation models the entrainment effect of the droplets on the airflow via a dispersed-phase continuum method that, due to the separation of length scales, treats the force exerted by the main droplets as a continuum smooth field. The trajectory and speed of the main droplets are also assumed to be unaffected by the airflow. The results indicate the existence of a dimensionless droplet density threshold (Nc) at which the vortex shifts from steady to oscillatory. This demonstrates that the two-dimensional instability has a supercritical Hopf type of bifurcation, i.e., the shift from stable to unstable is continuous but not smooth and the amplitude of oscillation follows the asymptotic square-root behavior characteristic of this type of bifurcation. Further, as shown by tests with stationary paper and no induced cross-flow, the mechanism of instability cannot be attributed to the interaction between the incoming cross-flow and the entrained airflow. Characterizing the two-dimensional airflow instabilities and their mechanism provides a better understanding of the airflow dynamics in the print gap of inkjet printers.


  • Top Cited Papers
    Open Access

    scikit-fem: A Python package for finite element assembly

    by Tom Gustafsson, G. D. McBain


  • Stability of a temporally evolving natural convection boundary layer on an isothermal wall

    by Junhao Ke, N. Williamson, S. W. Armfield, G. D. McBain, S. E. Norris

    The stability properties of a natural convection boundary layer adjacent to an isothermally heated vertical wall, with Prandtl number 0.71, are numerically investigated in the configuration of a temporally evolving parallel flow. The instantaneous linear stability of the flow is first investigated by solving the eigenvalue problem with a quasi-steady assumption, whereby the unsteady base flow is frozen in time. Temporal responses of the discrete perturbation modes are numerically obtained by solving the two-dimensional linearized disturbance equations using a ‘frozen’ base flow as an initial-value problem at various $Gr_{\unicode[STIX]{x1D6FF}}$ , where $Gr_{\unicode[STIX]{x1D6FF}}$ is the Grashof number based on the velocity integral boundary layer thickness $\unicode[STIX]{x1D6FF}$ . The resultant amplification rates of the discrete modes are compared with the quasi-steady eigenvalue analysis, and both two-dimensional and three-dimensional direct numerical simulations (DNS) of the temporally evolving flow. The amplification rate predicted by the linear theory compares well with the result of direct numerical simulation up to a transition point. The extent of the linear regime where the perturbations linearly interact with the base flow is thus identified. The value of the transition $Gr_{\unicode[STIX]{x1D6FF}}$ , according to the three-dimensional DNS results, is dependent on the initial perturbation amplitude. Beyond the transition point, the DNS results diverge from the linear stability predictions as nonlinear mechanisms become important.