Fabrice Guellec
Research Subjects
Fabrice Guellec has a total of 127 co-authors. Here are the top co-authors by number of shared publications:
Johan Rothman
CEA, LETI, MINATEC F-38054 Grenoble, France
9 shared publicationsPierre Castelein
CEA-LETI (France)
9 shared publicationsEric de Borniol
CEA/LETI, MINATEC Campus, 17 rue des Martyrs, 38054 Grenoble Cedex 9,France
6 shared publicationsEric De Borniol
CEA-LETI (France)
5 shared publicationsAndré Perez
CEA LETI-MINATEC (France)
4 shared publicationsGérard Destéfanis
CEA/LETI, MINATEC Campus, 17 rue des Martyrs, 38054 Grenoble Cedex 9,France
4 shared publications
Latest Publications
- 7 January 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 54 (4) , 1096-1105
A 5500-frames/s 85-GOPS/W 3-D Stacked BSI Vision Chip Based on Parallel In-Focal-Plane Acquisition and Processing
This paper presents a 3-D stacked vision chip featuring in-focal-plane read-out tightly coupled with flexible computing architecture for configurable high-speed image analysis. The chip architecture is based on a scalable standalone structure integrating image sensor on the top tier and processing elements (PEs) plus memories in the bottom tier. By using 3-D stacking partitioning, our prototype benefits from backside illuminated pixels sensitivity, a fully parallel communication between image sensor and PEs for low-latency performances, while leaving enough room in the bottom tier to embed advanced computing features. One scalable structure embeds a 16x16 pixel array (or 64x64 pixels in high-resolution mode), associated with an 8-bit single instruction multiple data (SIMD) processor; fabricated in dual 130-nm 1P6M CMOS process. This paper exhibits a 5500 frames/s and 85 giga operations per second (GOPS)/W in low-resolution mode, with large kernels capabilities through eight directions interpixel communication. Multiflow capability is also demonstrated to execute different programs in different areas of the vision chip.
- 7 January 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 54 (4) , 1096-1105
A 5500-frames/s 85-GOPS/W 3-D Stacked BSI Vision Chip Based on Parallel In-Focal-Plane Acquisition and Processing
This paper presents a 3-D stacked vision chip featuring in-focal-plane read-out tightly coupled with flexible computing architecture for configurable high-speed image analysis. The chip architecture is based on a scalable standalone structure integrating image sensor on the top tier and processing elements (PEs) plus memories in the bottom tier. By using 3-D stacking partitioning, our prototype benefits from backside illuminated pixels sensitivity, a fully parallel communication between image sensor and PEs for low-latency performances, while leaving enough room in the bottom tier to embed advanced computing features. One scalable structure embeds a 16x16 pixel array (or 64x64 pixels in high-resolution mode), associated with an 8-bit single instruction multiple data (SIMD) processor; fabricated in dual 130-nm 1P6M CMOS process. This paper exhibits a 5500 frames/s and 85 giga operations per second (GOPS)/W in low-resolution mode, with large kernels capabilities through eight directions interpixel communication. Multiflow capability is also demonstrated to execute different programs in different areas of the vision chip.
- Open Access
- 17 November 2017
- Published by SPIE-Intl Soc Optical Eng
- p. 152
ROIC development at CEA for SWIR detectors: pixel circuit architecture and trade-offs
- 17 November 2017
- Published by SPIE-Intl Soc Optical Eng
- p. 152
Open AccessROIC development at CEA for SWIR detectors: pixel circuit architecture and trade-offs
- 13 March 2015
- Published by SPIE-Intl Soc Optical Eng
- Vol. 9403, 940304-940304-11
Signal conditioning circuits for 3D-integrated burst image sensors with on-chip A/D conversion
- 13 March 2015
- Published by SPIE-Intl Soc Optical Eng
- Vol. 9403, 940304-940304-11
Signal conditioning circuits for 3D-integrated burst image sensors with on-chip A/D conversion
- 1 September 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 19308833,p. 303-306
A 533pW NEP 31×31 pixel THz image sensor based on in-pixel demodulation
A THz 31×31 pixel, 100 fps image sensor integrated in a 130 nm CMOS process is presented. Taking advantage of the possibility to modulate the active source that lights the scene, a significant improvement in sensitivity and NEP is achieved by shifting the modulated THz radiation, by means of an antenna/MOSFET, then filtering the signal band using an in-pixel 16-paths passive SC-filter combined with a CT Gm-C filter resulting in a high Q factor of 100. This THz imager features a measured NEP of 533 pW at 270 GHz and 732 pW at 600 GHz respectively, and a sensitive readout chain with an input referred noise of 0.2 μV RMS .
- 1 September 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 19308833,p. 303-306
A 533pW NEP 31×31 pixel THz image sensor based on in-pixel demodulation
A THz 31×31 pixel, 100 fps image sensor integrated in a 130 nm CMOS process is presented. Taking advantage of the possibility to modulate the active source that lights the scene, a significant improvement in sensitivity and NEP is achieved by shifting the modulated THz radiation, by means of an antenna/MOSFET, then filtering the signal band using an in-pixel 16-paths passive SC-filter combined with a CT Gm-C filter resulting in a high Q factor of 100. This THz imager features a measured NEP of 533 pW at 270 GHz and 732 pW at 600 GHz respectively, and a sensitive readout chain with an input referred noise of 0.2 μV RMS .
- 24 September 2013
- Published by SPIE-Intl Soc Optical Eng
- Vol. 8846, 88460O
Antenna-coupled microbolometer based uncooled 2D array and camera for 2D real-time terahertz imaging
- 24 September 2013
- Published by SPIE-Intl Soc Optical Eng
- Vol. 8846, 88460O
Antenna-coupled microbolometer based uncooled 2D array and camera for 2D real-time terahertz imaging
- 1 June 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
A novel 0.5GHz real time asynchronous photon detection and counting technique: ROIC design for cooled SWIR HgCdTe infrared detector
In this paper we present a new asynchronous readout technique designed for a single element infrared detector (SWIR HgCdTe APD). This circuit aims to perform photon counting on a hybridized detector at a cryogenic temperature for an atmospheric LIDAR (LIght Detection And Ranging) application. Accordingly, for the most important specifications, we obtain a very low input referred noise generated by the circuit ~100 μVrms ↔ 12 e - rms. Also, a bandwidth of 0.5GHz is achieved in order to satisfy the most demanding needs. The circuit architecture, the simulation bench and results are included and illustrated in this paper.
- 1 June 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
A novel 0.5GHz real time asynchronous photon detection and counting technique: ROIC design for cooled SWIR HgCdTe infrared detector
In this paper we present a new asynchronous readout technique designed for a single element infrared detector (SWIR HgCdTe APD). This circuit aims to perform photon counting on a hybridized detector at a cryogenic temperature for an atmospheric LIDAR (LIght Detection And Ranging) application. Accordingly, for the most important specifications, we obtain a very low input referred noise generated by the circuit ~100 μVrms ↔ 12 e - rms. Also, a bandwidth of 0.5GHz is achieved in order to satisfy the most demanding needs. The circuit architecture, the simulation bench and results are included and illustrated in this paper.
- 1 February 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 01936530,p. 394-395
A [10°C; 70°C] 640×480 17µm pixel pitch TEC-less IR bolometer imager with below 50mK and below 4V power supply
Used in low-cost thermal imaging, 8-to-12μm infrared micro-bolometer hybrid detectors are very demanding in terms of offset skimming and technological fluctuation compensation: typical offset values are about 100 times larger than the signal, while the fixed-pattern noise (FPN) is about 10 times larger. State-of-the-art image sensors feature noise-equivalent temperature difference (NETD), i.e. thermal resolutions, of about 50mK.
- 1 February 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 01936530,p. 394-395
A [10°C; 70°C] 640×480 17µm pixel pitch TEC-less IR bolometer imager with below 50mK and below 4V power supply
Used in low-cost thermal imaging, 8-to-12μm infrared micro-bolometer hybrid detectors are very demanding in terms of offset skimming and technological fluctuation compensation: typical offset values are about 100 times larger than the signal, while the fixed-pattern noise (FPN) is about 10 times larger. State-of-the-art image sensors feature noise-equivalent temperature difference (NETD), i.e. thermal resolutions, of about 50mK.
- 22 August 2012
- Published by SPIE-Intl Soc Optical Eng
- Vol. 8442, 84421I
Design of the MWIR channels of EChO
In this paper, we present the design of the MWIR channels of EChO. Two channels cover the 5-11 micron spectral range. The choice of the boundaries of each channel is a trade-off driven by the science goals (spectral features of key molecules) and several parameters such as the common optics design, the dichroic plates design, the optical materials characteristics, the detector cut-off wavelength. We also will emphasize the role of the detectors choice that drives the thermal and mechanical designs and the cooling strategy.
- 22 August 2012
- Published by SPIE-Intl Soc Optical Eng
- Vol. 8442, 84421I
Design of the MWIR channels of EChO
In this paper, we present the design of the MWIR channels of EChO. Two channels cover the 5-11 micron spectral range. The choice of the boundaries of each channel is a trade-off driven by the science goals (spectral features of key molecules) and several parameters such as the common optics design, the dichroic plates design, the optical materials characteristics, the detector cut-off wavelength. We also will emphasize the role of the detectors choice that drives the thermal and mechanical designs and the cooling strategy.
- 1 June 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 21585601,p. 128-129
An 88dB SNR, 30µm pixel pitch Infra-Red image sensor with a 2-step 16 bit A/D conversion
A new readout IC (ROIC) with a 2 step A/D conversion for cooled infrared image sensors is presented in this paper. The sensor operates at a 50Hz frame rate in an Integrate-While-Read snapshot mode. The 16 bit ADC resolution preserves the excellent detector SNR at full well (~3Ge-). The ROIC, featuring a 320×256 array with 30μm pixel pitch, has been designed in a standard 0.18μm CMOS technology. The IC has been hybridized (indium bump bonding) to a LWIR (Long Wave Infra Red) detector fabricated using our in-house HgCdTe process. The first measurement results of the detector assembly validate both the 2-step ADC concept and its circuit implementation. This work sets a new state-of-the-art SNR of 88dB.
- 1 June 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 21585601,p. 128-129
An 88dB SNR, 30µm pixel pitch Infra-Red image sensor with a 2-step 16 bit A/D conversion
A new readout IC (ROIC) with a 2 step A/D conversion for cooled infrared image sensors is presented in this paper. The sensor operates at a 50Hz frame rate in an Integrate-While-Read snapshot mode. The 16 bit ADC resolution preserves the excellent detector SNR at full well (~3Ge-). The ROIC, featuring a 320×256 array with 30μm pixel pitch, has been designed in a standard 0.18μm CMOS technology. The IC has been hybridized (indium bump bonding) to a LWIR (Long Wave Infra Red) detector fabricated using our in-house HgCdTe process. The first measurement results of the detector assembly validate both the 2-step ADC concept and its circuit implementation. This work sets a new state-of-the-art SNR of 88dB.
- 22 May 2012
- Published by SPIE-Intl Soc Optical Eng in Optical Engineering
- Vol. 51 (6) , 061305-1-061305-6
Active three-dimensional and thermal imaging with a 30-μm pitch 320×256 HgCdTe avalanche photodiode focal plane array
Three-dimensional (3-D) flash light detection and ranging (LADAR) imaging is based on time of flight (TOF) measurement of a single laser pulse. The laser pulse coming back from the observed object will be detected only if the number of photons received by each pixel generates a signal greater than the pixel noise. In order to extract this weak photonic signal from the noise we use the high gain and low excess noise of the HgCdTe avalanche photodiode (APD) arrays developed at CEA/LETI. The sensor consists of a 30-μm pitch APD detector array hybridized to a ROIC for passive and active imaging. In passive mode the focal plane array behaves like a thermal imager and we measured 30 mK of noise-equivalent temperature difference. In active imaging mode, each pixel sensed the time of flight and the intensity two-dimensional (2-D) of a single laser pulse. Laboratory tests show a range noise of 11 cm for 4300 photoelectrons per pixel and detection limit under 100 photoelectrons. The sensor was also used during a field trial to record 2-D and 3-D real-time videos. The quality of the images obtained demonstrates the maturity of HgCdTe-APD-array technology.- 22 May 2012
- Published by SPIE-Intl Soc Optical Eng in Optical Engineering
- Vol. 51 (6) , 061305-1-061305-6
Active three-dimensional and thermal imaging with a 30-μm pitch 320×256 HgCdTe avalanche photodiode focal plane array
Three-dimensional (3-D) flash light detection and ranging (LADAR) imaging is based on time of flight (TOF) measurement of a single laser pulse. The laser pulse coming back from the observed object will be detected only if the number of photons received by each pixel generates a signal greater than the pixel noise. In order to extract this weak photonic signal from the noise we use the high gain and low excess noise of the HgCdTe avalanche photodiode (APD) arrays developed at CEA/LETI. The sensor consists of a 30-μm pitch APD detector array hybridized to a ROIC for passive and active imaging. In passive mode the focal plane array behaves like a thermal imager and we measured 30 mK of noise-equivalent temperature difference. In active imaging mode, each pixel sensed the time of flight and the intensity two-dimensional (2-D) of a single laser pulse. Laboratory tests show a range noise of 11 cm for 4300 photoelectrons per pixel and detection limit under 100 photoelectrons. The sensor was also used during a field trial to record 2-D and 3-D real-time videos. The quality of the images obtained demonstrates the maturity of HgCdTe-APD-array technology.