Dagang Zhao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Dagang Zhao has a total of 45 co-authors. Here are the top co-authors by number of shared publications:
- Chunyu Guo
College of Shipbuilding Engineering, Harbin Engineering University, Harbin 150001, China
6 shared publications - Chao Wang
College of Shipbuilding Engineering, Harbin Engineering University, Harbin 150001, China
4 shared publications - Jianfeng Lin
College of Shipbuilding Engineering, Harbin Engineering University, Harbin 150001, China
3 shared publications - Xianghai Zhong
College of Shipbuilding Engineering, Harbin Engineering University, Harbin 150001, China
3 shared publications - Cong Sun
College of Shipbuilding Engineering, Harbin Engineering University, Harbin 150001, China
2 shared publications - Mingqi Bi
College of Shipbuilding Engineering, Harbin Engineering University, Harbin 150001, China
2 shared publications
Latest Publications
- Open Access
- 31 May 2026
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 14 (11) , 1032
Numerical Research on Excitation Force Characteristics of Pre-Swirl Stator–Propeller–Rudder System
The present study conducts numerical simulations to investigate the excitation force characteristics of a pre-swirl stator–propeller–rudder system and analyzes the potential benefits of the combined pre-swirl stator and rudder bulb for vibration and noise based on force and pressure fluctuations. The propeller bearing force, rudder force and hull surface pressure are compared and analyzed under conditions with and without energy-saving devices. The results show that the pre-swirl stator and rudder bulb intensify the axial load pulsation of the propeller, which may affect the service life of the main engine and gearbox. The overall level of lateral load pulsation is also increased, which may lead to higher cabin noise. The load pulsation level of the pre-swirl stator is comparable to that of the propeller bearing force, while the increased vibration of the rudder may result in more complex structural safety and noise issues. The reduction in hull surface pressure fluctuation contributes to the mitigation of the low-frequency underwater radiated noise. The influence mechanism of the pre-swirl stator–rudder bulb on the excitation force is of great significance to the ship engineering design.
- 31 May 2026
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 14 (11) , 1032
Open AccessNumerical Research on Excitation Force Characteristics of Pre-Swirl Stator–Propeller–Rudder System
The present study conducts numerical simulations to investigate the excitation force characteristics of a pre-swirl stator–propeller–rudder system and analyzes the potential benefits of the combined pre-swirl stator and rudder bulb for vibration and noise based on force and pressure fluctuations. The propeller bearing force, rudder force and hull surface pressure are compared and analyzed under conditions with and without energy-saving devices. The results show that the pre-swirl stator and rudder bulb intensify the axial load pulsation of the propeller, which may affect the service life of the main engine and gearbox. The overall level of lateral load pulsation is also increased, which may lead to higher cabin noise. The load pulsation level of the pre-swirl stator is comparable to that of the propeller bearing force, while the increased vibration of the rudder may result in more complex structural safety and noise issues. The reduction in hull surface pressure fluctuation contributes to the mitigation of the low-frequency underwater radiated noise. The influence mechanism of the pre-swirl stator–rudder bulb on the excitation force is of great significance to the ship engineering design.
- Open Access
- 11 May 2026
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 14 (10) , 886
Numerical Investigation of Poisson’s Ratio Effects on Ice–Structure Interaction Using the Peridynamic Method
The peridynamic (PD) method has been widely utilized in the numerical modelling of ice–structure interactions due to its capability to naturally capture material failure and fracture evolution. PD formulations can be categorized into bond-based and state-based models. While the bond-based model offers computational simplicity, it inherently restricts Poisson’s ratio to 1/4 in three-dimensional (3D) simulations and 1/3 in two-dimensional (2D) simulations. In contrast, the state-based model allows for arbitrary Poisson’s ratios, which is essential for accurately modelling ice mechanics, as Poisson’s ratio of ice commonly exceeds 0.33 and can reach up to 0.42. This study employs the PD method coupled with the discrete energy release rate criterion to analyze the influence of Poisson’s ratio on ice failure mechanisms and ice-induced loads in two typical scenarios: cylindrical impact on an ice disc and ice–structure interaction with a propeller blade. The benchmark compression test yielded computed Poisson’s ratios of 0.215, 0.258, 0.333, and 0.401 for prescribed values of 0.2, 0.25, 0.33, and 0.40, corresponding to relative errors of 7.5%, 3.2%, 1.02%, and 0.38%, respectively. And the fracture simulations indicate that variations in Poisson’s ratio affects ice fracture patterns and load distributions, underscoring the limitations of the bond-based PD model in accurately representing ice–structure interactions. These findings highlight the necessity of adopting state-based PD formulations for improved numerical predictions of ice-induced mechanical responses.
- 11 May 2026
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 14 (10) , 886
Open AccessNumerical Investigation of Poisson’s Ratio Effects on Ice–Structure Interaction Using the Peridynamic Method
The peridynamic (PD) method has been widely utilized in the numerical modelling of ice–structure interactions due to its capability to naturally capture material failure and fracture evolution. PD formulations can be categorized into bond-based and state-based models. While the bond-based model offers computational simplicity, it inherently restricts Poisson’s ratio to 1/4 in three-dimensional (3D) simulations and 1/3 in two-dimensional (2D) simulations. In contrast, the state-based model allows for arbitrary Poisson’s ratios, which is essential for accurately modelling ice mechanics, as Poisson’s ratio of ice commonly exceeds 0.33 and can reach up to 0.42. This study employs the PD method coupled with the discrete energy release rate criterion to analyze the influence of Poisson’s ratio on ice failure mechanisms and ice-induced loads in two typical scenarios: cylindrical impact on an ice disc and ice–structure interaction with a propeller blade. The benchmark compression test yielded computed Poisson’s ratios of 0.215, 0.258, 0.333, and 0.401 for prescribed values of 0.2, 0.25, 0.33, and 0.40, corresponding to relative errors of 7.5%, 3.2%, 1.02%, and 0.38%, respectively. And the fracture simulations indicate that variations in Poisson’s ratio affects ice fracture patterns and load distributions, underscoring the limitations of the bond-based PD model in accurately representing ice–structure interactions. These findings highlight the necessity of adopting state-based PD formulations for improved numerical predictions of ice-induced mechanical responses.
- 1 December 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (12)
Numerical study on aerodynamic characteristics of finite-length tandem rotating cylinders
Aerodynamic interference in flow around tandem rotating cylinders (e.g., Flettner rotors) is characterized by significant complexity for engineering applications. Large eddy simulation is employed to investigate aerodynamic characteristics of finite-length tandem cylinders at a subcritical Reynolds number of 3900, with focus placed on spacing ratios (L/D) of 3, 4, and 5 and speed ratios (n) ranging from 0 to 5. For stationary cylinders (n = 0), three distinct flow regimes are identified. When rotation initiates (n = 1), flow instability is intensified. The key phenomenon of “drag reversal” emerges at n ≥ 2. This transition is attributed to coupling between the blockage effect and the rotational action. At the critical speed ratio (n = 3), vortex shedding is suppressed. At high-speed ratios (n > 3), the flow transitions into a rotation-dominated regime, where a secondary instability mode is activated. A synergy between blockage effects and rotational action is revealed, enabling relative optimal operation at L/D = 3 and n = 3 with high lift-drag ratio and achieving minimal fluctuating loads. Critical theoretical and practical guidance for optimizing tandem cylinder flow configurations in Flettner rotors is provided with these findings.
- 1 December 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (12)
Numerical study on aerodynamic characteristics of finite-length tandem rotating cylinders
Aerodynamic interference in flow around tandem rotating cylinders (e.g., Flettner rotors) is characterized by significant complexity for engineering applications. Large eddy simulation is employed to investigate aerodynamic characteristics of finite-length tandem cylinders at a subcritical Reynolds number of 3900, with focus placed on spacing ratios (L/D) of 3, 4, and 5 and speed ratios (n) ranging from 0 to 5. For stationary cylinders (n = 0), three distinct flow regimes are identified. When rotation initiates (n = 1), flow instability is intensified. The key phenomenon of “drag reversal” emerges at n ≥ 2. This transition is attributed to coupling between the blockage effect and the rotational action. At the critical speed ratio (n = 3), vortex shedding is suppressed. At high-speed ratios (n > 3), the flow transitions into a rotation-dominated regime, where a secondary instability mode is activated. A synergy between blockage effects and rotational action is revealed, enabling relative optimal operation at L/D = 3 and n = 3 with high lift-drag ratio and achieving minimal fluctuating loads. Critical theoretical and practical guidance for optimizing tandem cylinder flow configurations in Flettner rotors is provided with these findings.
- 1 January 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (1)
On the stability of submerged gas jet in temporal mode
The temporal mode stability of incompressible submerged axisymmetric gas jets is comprehensively investigated by linear stability analysis. The basic velocity profile is constructed using the hyperbolic tangent function approach. The influences of basic velocity profile, Reynolds Re, and Weber We numbers, and physical properties of the surrounding liquid on the stability of the gas jet are investigated and stability maps are constructed. We find that the jet breakup propagation velocity shows a strong linear relationship with the velocity of the two-phase interface, and the shear on the interface can greatly change the instability modes of submerged gas jet system. Large surface tension triggers long-wave instability of the jet and local shear at the interface leads to the unsteady transition to short-wave instability. Moreover, it is found that there is a strong linear relationship between the most unstable growth rate and dimensionless parameters directly or indirectly, and R2 is above 0.95. In addition, the instability of the submerged gas jet shows a double-mode feature when the velocity profile parameters exceed their thresholds.
- 1 January 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (1)
On the stability of submerged gas jet in temporal mode
The temporal mode stability of incompressible submerged axisymmetric gas jets is comprehensively investigated by linear stability analysis. The basic velocity profile is constructed using the hyperbolic tangent function approach. The influences of basic velocity profile, Reynolds Re, and Weber We numbers, and physical properties of the surrounding liquid on the stability of the gas jet are investigated and stability maps are constructed. We find that the jet breakup propagation velocity shows a strong linear relationship with the velocity of the two-phase interface, and the shear on the interface can greatly change the instability modes of submerged gas jet system. Large surface tension triggers long-wave instability of the jet and local shear at the interface leads to the unsteady transition to short-wave instability. Moreover, it is found that there is a strong linear relationship between the most unstable growth rate and dimensionless parameters directly or indirectly, and R2 is above 0.95. In addition, the instability of the submerged gas jet shows a double-mode feature when the velocity profile parameters exceed their thresholds.
- Open Access
- 26 June 2023
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 11 (7) , 1300
Research on Scale Effect of Resistance Components for Full-Formed Ship Based on Large-Scale Model Towing Test
In recent years, the International Maritime Organization (IMO) has gradually introduced more stringent new Ship Energy Efficiency Design Index (EEDI) bills, and transport ships are more inclined to reduce the speed and increase the length and square coefficient to meet the design requirements. However, the size of the ship model that can be accommodated in the towing tank is seriously limited. Under the action of the scale effect, the accuracy of the prediction results of the resistance performance of large ships is particularly prominent. To break through the limitations of the test site, a large-scale ship model resistance towing test system and data analysis method in the port were established. By comparing with the results of small-scale model tests in the towing tank, the applicability of the 1957 ITTC friction line and Grigson friction line in the resistance prediction of the full-formed ship was analyzed, and the scale effects of resistance components were also examined. The results show that the scale effect of the form factor of full-formed ships is weak. The three-dimension method based on the empirical formula of mixed-form friction resistance of ITTC-Grigson is more suitable for predicting the resistance performance of full-formed ships.
- 26 June 2023
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 11 (7) , 1300
Open AccessResearch on Scale Effect of Resistance Components for Full-Formed Ship Based on Large-Scale Model Towing Test
In recent years, the International Maritime Organization (IMO) has gradually introduced more stringent new Ship Energy Efficiency Design Index (EEDI) bills, and transport ships are more inclined to reduce the speed and increase the length and square coefficient to meet the design requirements. However, the size of the ship model that can be accommodated in the towing tank is seriously limited. Under the action of the scale effect, the accuracy of the prediction results of the resistance performance of large ships is particularly prominent. To break through the limitations of the test site, a large-scale ship model resistance towing test system and data analysis method in the port were established. By comparing with the results of small-scale model tests in the towing tank, the applicability of the 1957 ITTC friction line and Grigson friction line in the resistance prediction of the full-formed ship was analyzed, and the scale effects of resistance components were also examined. The results show that the scale effect of the form factor of full-formed ships is weak. The three-dimension method based on the empirical formula of mixed-form friction resistance of ITTC-Grigson is more suitable for predicting the resistance performance of full-formed ships.
- Open Access
- 1 June 2023
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 11 (6) , 1162
The Aerodynamic Characteristics of a Rotating Cylinder Based on Large-Eddy Simulations
The cylindrical flow around a cylinder is present in several engineering problems. Moreover, the flow pattern around a rotating cylinder is more complex than that around a cylinder. In this paper, a rotating cylinder at different speed ratios is investigated by means of large-eddy simulations. In particular, the lift coefficient CL, drag coefficient CD, lift-to-drag ratio k, Strouhal number St, the flow field in each section, and the three-dimensional eddy structure are compared at different speed ratios. In addition, the effects of an end disk on the aerodynamic loads and flow field of the rotating cylinder were investigated. The results showed that, in the absence of an end disk, CL increased, CD increased and then decreased, k increased and then decreased, and St increased and then decreased as the speed ratio increased. The turnaround occurs for each parameter at a speed ratio of n = 2, and vortex shedding is suppressed at this speed ratio. Notably, the tip vortex at the free end was not suppressed. The CL, CD, and k values of the cylinder when adding the end disk were greater than those of the normal cylinder. For example, when the speed ratio is 3, the lift coefficient is increased by 27%, the drag coefficient is increased by 24%, and the lift-to-drag ratio is increased by 23% after adding the end plate. In addition, the vortex structure at the free end differed substantially. This study provides a systematic method to evaluate the aerodynamic loads and flow field changes around a cylinder, laying the foundation for solving the problems of cylinder flow and rotating cylinder flow.
- 1 June 2023
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 11 (6) , 1162
Open AccessThe Aerodynamic Characteristics of a Rotating Cylinder Based on Large-Eddy Simulations
The cylindrical flow around a cylinder is present in several engineering problems. Moreover, the flow pattern around a rotating cylinder is more complex than that around a cylinder. In this paper, a rotating cylinder at different speed ratios is investigated by means of large-eddy simulations. In particular, the lift coefficient CL, drag coefficient CD, lift-to-drag ratio k, Strouhal number St, the flow field in each section, and the three-dimensional eddy structure are compared at different speed ratios. In addition, the effects of an end disk on the aerodynamic loads and flow field of the rotating cylinder were investigated. The results showed that, in the absence of an end disk, CL increased, CD increased and then decreased, k increased and then decreased, and St increased and then decreased as the speed ratio increased. The turnaround occurs for each parameter at a speed ratio of n = 2, and vortex shedding is suppressed at this speed ratio. Notably, the tip vortex at the free end was not suppressed. The CL, CD, and k values of the cylinder when adding the end disk were greater than those of the normal cylinder. For example, when the speed ratio is 3, the lift coefficient is increased by 27%, the drag coefficient is increased by 24%, and the lift-to-drag ratio is increased by 23% after adding the end plate. In addition, the vortex structure at the free end differed substantially. This study provides a systematic method to evaluate the aerodynamic loads and flow field changes around a cylinder, laying the foundation for solving the problems of cylinder flow and rotating cylinder flow.
- Open Access
- 12 July 2022
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 10 (7) , 953
Hydrodynamic and Flow Field Characteristics of Water Jet Propulsion under Mooring Conditions
The acceleration characteristics of a water jet-propelled ship during startup are related to its performance under mooring conditions. Water jet propulsion cavitation during startup increases the vibration and noise of the whole ship. Therefore, accurately predicting and analyzing the performance, hydrodynamics and flow field characteristics of water jet-propelled ships under mooring conditions can help elucidate the startup characteristics of the ships and optimize their acceleration strategies. In this study, the hydrodynamic and flow field characteristics of water jet propulsion and water jet propulsion ships under mooring conditions were studied using three-dimensional numerical modeling. First, the hydrodynamic performance of the water jet propeller was analyzed, and the relevant flow field law was derived. Then, the hydrodynamic performance, internal and external flow field characteristics, pulsation pressure and flow rate at the nozzle, and pulsation pressure at the monitoring points around the impeller of the water jet propulsion ship model were analyzed under mooring conditions. We obtained the open-water law for the water jet propeller and the hydrodynamic force and flow field law for a two-pump water jet propulsion ship. The ship model developed in this study provides a good theoretical foundation for further research on water jet propulsion.
- 12 July 2022
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 10 (7) , 953
Open AccessHydrodynamic and Flow Field Characteristics of Water Jet Propulsion under Mooring Conditions
The acceleration characteristics of a water jet-propelled ship during startup are related to its performance under mooring conditions. Water jet propulsion cavitation during startup increases the vibration and noise of the whole ship. Therefore, accurately predicting and analyzing the performance, hydrodynamics and flow field characteristics of water jet-propelled ships under mooring conditions can help elucidate the startup characteristics of the ships and optimize their acceleration strategies. In this study, the hydrodynamic and flow field characteristics of water jet propulsion and water jet propulsion ships under mooring conditions were studied using three-dimensional numerical modeling. First, the hydrodynamic performance of the water jet propeller was analyzed, and the relevant flow field law was derived. Then, the hydrodynamic performance, internal and external flow field characteristics, pulsation pressure and flow rate at the nozzle, and pulsation pressure at the monitoring points around the impeller of the water jet propulsion ship model were analyzed under mooring conditions. We obtained the open-water law for the water jet propeller and the hydrodynamic force and flow field law for a two-pump water jet propulsion ship. The ship model developed in this study provides a good theoretical foundation for further research on water jet propulsion.
- Open Access
- 4 October 2020
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 8 (10) , 777
Real-Time Prediction of Large-Scale Ship Model Vertical Acceleration Based on Recurrent Neural Network
In marine environments, ships are bound to be disturbed by several external factors, which can cause stochastic fluctuations and strong nonlinearity in the ship motion. Predicting ship motion is pivotal to ensuring ship safety and providing early warning of risks. This report proposes a real-time ship vertical acceleration prediction algorithm based on the long short-term memory (LSTM) and gated recurrent units (GRU) models of a recurrent neural network. The vertical acceleration time history data at the bow, middle, and stern of a large-scale ship model were obtained by performing a self-propulsion test at sea, and the original data were pre-processed by resampling and normalisation via Python. The prediction results revealed that the proposed algorithm could accurately predict the acceleration time history data of the large-scale ship model, and the root mean square error between the predicted and real values was no greater than 0.1. The optimised multivariate time series prediction program could reduce the calculation time by approximately 55% compared to that of a univariate time series prediction program, and the run time of the GRU model was better than that of the LSTM model.
- 4 October 2020
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 8 (10) , 777
Open AccessReal-Time Prediction of Large-Scale Ship Model Vertical Acceleration Based on Recurrent Neural Network
In marine environments, ships are bound to be disturbed by several external factors, which can cause stochastic fluctuations and strong nonlinearity in the ship motion. Predicting ship motion is pivotal to ensuring ship safety and providing early warning of risks. This report proposes a real-time ship vertical acceleration prediction algorithm based on the long short-term memory (LSTM) and gated recurrent units (GRU) models of a recurrent neural network. The vertical acceleration time history data at the bow, middle, and stern of a large-scale ship model were obtained by performing a self-propulsion test at sea, and the original data were pre-processed by resampling and normalisation via Python. The prediction results revealed that the proposed algorithm could accurately predict the acceleration time history data of the large-scale ship model, and the root mean square error between the predicted and real values was no greater than 0.1. The optimised multivariate time series prediction program could reduce the calculation time by approximately 55% compared to that of a univariate time series prediction program, and the run time of the GRU model was better than that of the LSTM model.
- Open Access
- 1 September 2020
- Published by Springer Nature in Journal of Marine Science and Application
- Vol. 19 (3) , 388-397
Numerical and Experimental Analysis of the Hydrodynamic Performance of a Three-Dimensional Finite-Length Rotating Cylinder
- 1 September 2020
- Published by Springer Nature in Journal of Marine Science and Application
- Vol. 19 (3) , 388-397
Open AccessNumerical and Experimental Analysis of the Hydrodynamic Performance of a Three-Dimensional Finite-Length Rotating Cylinder
- Open Access
- 30 May 2020
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 8 (6) , 398
Uncertainty Analysis of Ship Model Propulsion Test on Actual Seas Based on Monte Carlo Method
As a new testing technology, large-scale ship model tests on the sea are advantageous in addressing the scale effect in ship models and in simulating ship navigation conditions. In this study, the uncertainty of a ship model propulsion test on the sea was analyzed using the Monte Carlo method, and the influence of the test environment was quantified. We used a 25 m-long ship model for the propulsion performance test. Based on the procedure recommended by the International Standardization Organization (ISO), several tests were conducted on the Yellow Sea (the northwestern part of the East China Sea). The results demonstrate that the wind and waves in the environment are the two factors that have the greatest influence on the test accuracy. This study will aid the development of sea trials, and the analysis method used in the propulsion test is also suitable for many complex ship tests.
- 30 May 2020
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 8 (6) , 398
Open AccessUncertainty Analysis of Ship Model Propulsion Test on Actual Seas Based on Monte Carlo Method
As a new testing technology, large-scale ship model tests on the sea are advantageous in addressing the scale effect in ship models and in simulating ship navigation conditions. In this study, the uncertainty of a ship model propulsion test on the sea was analyzed using the Monte Carlo method, and the influence of the test environment was quantified. We used a 25 m-long ship model for the propulsion performance test. Based on the procedure recommended by the International Standardization Organization (ISO), several tests were conducted on the Yellow Sea (the northwestern part of the East China Sea). The results demonstrate that the wind and waves in the environment are the two factors that have the greatest influence on the test accuracy. This study will aid the development of sea trials, and the analysis method used in the propulsion test is also suitable for many complex ship tests.