Justin Thomas
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Justin Thomas has a total of 56 co-authors. Here are the top co-authors by number of shared publications:
Vijay Kumar
GRASP Laboratory University of Pennsylvania Philadelphia Pennsylvania
20 shared publications- Giuseppe Loianno
Department of Electrical Engineering and Computer Sciences, University of California, Berkeley, Berkeley, CA, USA
17 shared publications Kostas Daniilidis
General Robotics Automation Sensing and Perception Laboratory, University of Pennsylvania, Philadelphia, PA, USA
5 shared publicationsKoushil Sreenath
Robotics Institute
3 shared publicationsMartin Saska
Department of Cybernetics Faculty of Electrical Engineering, Czech Technical University Prague Czech Republic
3 shared publications- Martin Saska
Czech Technical University in Prague
3 shared publications
Latest Publications
- 22 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 4 (4) , 3860-3867
Analysis of Ground Effect for Small-Scale UAVs in Forward Flight
The letter investigates how the behavior of small-scale unmanned aerial vehicles (UAVs) is influenced by the system's close proximity to the ground/rigid surfaces both at hover and in forward flight. We perform an extensive experimental study where a quadrotor is tasked with flying in forward velocities in the range of 0–8 m/s and at altitudes that range between 0.05–0.5 m. Experimental data are used to evaluate four existing ground effect models. Results suggest that existing models for helicopters and in-hover multi-rotors cannot fully describe the forward motion of a quadrotor when it operates close to ground. We introduce two new data-driven models for rotorcraft operating in ground effect both at hover and in forward flight, and evaluate the proposed models with another quadrotor of different size. The proposed models simultaneously consider several operating conditions, which are parameterized by the vehicle's forward velocity and altitude. The models link the thrust produced when operating in ground effect and hovering out of ground effect as forward velocities vary. This information can be incorporated into flight controllers for robust and adaptive UAV flights, and can benefit motion planners for safe and energy efficient near-ground trajectory planning.
- 22 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 4 (4) , 3860-3867
Analysis of Ground Effect for Small-Scale UAVs in Forward Flight
The letter investigates how the behavior of small-scale unmanned aerial vehicles (UAVs) is influenced by the system's close proximity to the ground/rigid surfaces both at hover and in forward flight. We perform an extensive experimental study where a quadrotor is tasked with flying in forward velocities in the range of 0–8 m/s and at altitudes that range between 0.05–0.5 m. Experimental data are used to evaluate four existing ground effect models. Results suggest that existing models for helicopters and in-hover multi-rotors cannot fully describe the forward motion of a quadrotor when it operates close to ground. We introduce two new data-driven models for rotorcraft operating in ground effect both at hover and in forward flight, and evaluate the proposed models with another quadrotor of different size. The proposed models simultaneously consider several operating conditions, which are parameterized by the vehicle's forward velocity and altitude. The models link the thrust produced when operating in ground effect and hovering out of ground effect as forward velocities vary. This information can be incorporated into flight controllers for robust and adaptive UAV flights, and can benefit motion planners for safe and energy efficient near-ground trajectory planning.
- Top Cited Papers
- 4 January 2019
- Published by Wiley in Journal of Field Robotics
- Vol. 36 (5) , 874-891
Autonomous landing on a moving vehicle with an unmanned aerial vehicle
This paper addresses the perception, control, and trajectory planning for an aerial platform to identify and land on a moving car at 15 km/hr. The hexacopter unmanned aerial vehicle (UAV), equipped with onboard sensors and a computer, detects the car using a monocular camera and predicts the car future movement using a nonlinear motion model. While following the car, the UAV lands on its roof, and it attaches itself using magnetic legs. The proposed system is fully autonomous from takeoff to landing. Numerous field tests were conducted throughout the year‐long development and preparations for the Mohamed Bin Zayed International Robotics Challenge (MBZIRC) 2017 competition, for which the system was designed. We propose a novel control system in which a model predictive controller is used in real time to generate a reference trajectory for the UAV, which are then tracked by the nonlinear feedback controller. This combination allows to track predictions of the car motion with minimal position error. The evaluation presents three successful autonomous landings during the MBZIRC 2017, where our system achieved the fastest landing among all competing teams.
- 4 January 2019
- Published by Wiley in Journal of Field Robotics
- Vol. 36 (5) , 874-891
Top Cited PapersAutonomous landing on a moving vehicle with an unmanned aerial vehicle
This paper addresses the perception, control, and trajectory planning for an aerial platform to identify and land on a moving car at 15 km/hr. The hexacopter unmanned aerial vehicle (UAV), equipped with onboard sensors and a computer, detects the car using a monocular camera and predicts the car future movement using a nonlinear motion model. While following the car, the UAV lands on its roof, and it attaches itself using magnetic legs. The proposed system is fully autonomous from takeoff to landing. Numerous field tests were conducted throughout the year‐long development and preparations for the Mohamed Bin Zayed International Robotics Challenge (MBZIRC) 2017 competition, for which the system was designed. We propose a novel control system in which a model predictive controller is used in real time to generate a reference trajectory for the UAV, which are then tracked by the nonlinear feedback controller. This combination allows to track predictions of the car motion with minimal position error. The evaluation presents three successful autonomous landings during the MBZIRC 2017, where our system achieved the fastest landing among all competing teams.
- 24 October 2018
- Published by Wiley in Journal of Field Robotics
- Vol. 36 (1) , 125-148
Cooperative autonomous search, grasping, and delivering in a treasure hunt scenario by a team of unmanned aerial vehicles
This paper addresses the problem of autonomous cooperative localization, grasping and delivering of colored ferrous objects by a team of unmanned aerial vehicles (UAVs). In the proposed scenario, a team of UAVs is required to maximize the reward by collecting colored objects and delivering them to a predefined location. This task consists of several subtasks such as cooperative coverage path planning, object detection and state estimation, UAV self‐localization, precise motion control, trajectory tracking, aerial grasping and dropping, and decentralized team coordination. The failure recovery and synchronization job manager is used to integrate all the presented subtasks together and also to decrease the vulnerability to individual subtask failures in real‐world conditions. The whole system was developed for the Mohamed Bin Zayed International Robotics Challenge (MBZIRC) 2017, where it achieved the highest score and won Challenge No. 3—Treasure Hunt. This paper does not only contain results from the MBZIRC 2017 competition but it also evaluates the system performance in simulations and field tests that were conducted throughout the year‐long development and preparations for the competition.
- 24 October 2018
- Published by Wiley in Journal of Field Robotics
- Vol. 36 (1) , 125-148
Cooperative autonomous search, grasping, and delivering in a treasure hunt scenario by a team of unmanned aerial vehicles
This paper addresses the problem of autonomous cooperative localization, grasping and delivering of colored ferrous objects by a team of unmanned aerial vehicles (UAVs). In the proposed scenario, a team of UAVs is required to maximize the reward by collecting colored objects and delivering them to a predefined location. This task consists of several subtasks such as cooperative coverage path planning, object detection and state estimation, UAV self‐localization, precise motion control, trajectory tracking, aerial grasping and dropping, and decentralized team coordination. The failure recovery and synchronization job manager is used to integrate all the presented subtasks together and also to decrease the vulnerability to individual subtask failures in real‐world conditions. The whole system was developed for the Mohamed Bin Zayed International Robotics Challenge (MBZIRC) 2017, where it achieved the highest score and won Challenge No. 3—Treasure Hunt. This paper does not only contain results from the MBZIRC 2017 competition but it also evaluates the system performance in simulations and field tests that were conducted throughout the year‐long development and preparations for the competition.
- 31 January 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 3 (3) , 1576-1583
Localization, Grasping, and Transportation of Magnetic Objects by a Team of MAVs in Challenging Desert-Like Environments
Autonomous Micro Aerial Vehicles (MAVs) have the potential to assist in real-life tasks involving grasping and transportation, but not before solving several difficult research challenges. In this work, we address the design, control, estimation, and planning problems for cooperative localization, grasping, and transportation of objects in challenging outdoor scenarios. We demonstrate an autonomous team of MAVs able to plan safe trajectories for manipulation of ferrous objects, while guaranteeing interrobot collision avoidance and automatically creating a map of the objects in the environment. Our solution is predominantly distributed, allowing the team to pick and transport ferrous disks to a final destination without collisions. This result is achieved using a new magnetic gripper with a novel feedback approach, enabling the detection of successful grasping. The gripper design and all the components to build a platform are clearly provided as open-source hardware for reuse by the community. Finally, the proposed solution is validated through experimental results, where difficulties include inconsistent wind, uneven terrain, and sandy conditions.
- 31 January 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 3 (3) , 1576-1583
Localization, Grasping, and Transportation of Magnetic Objects by a Team of MAVs in Challenging Desert-Like Environments
Autonomous Micro Aerial Vehicles (MAVs) have the potential to assist in real-life tasks involving grasping and transportation, but not before solving several difficult research challenges. In this work, we address the design, control, estimation, and planning problems for cooperative localization, grasping, and transportation of objects in challenging outdoor scenarios. We demonstrate an autonomous team of MAVs able to plan safe trajectories for manipulation of ferrous objects, while guaranteeing interrobot collision avoidance and automatically creating a map of the objects in the environment. Our solution is predominantly distributed, allowing the team to pick and transport ferrous disks to a final destination without collisions. This result is achieved using a new magnetic gripper with a novel feedback approach, enabling the detection of successful grasping. The gripper design and all the components to build a platform are clearly provided as open-source hardware for reuse by the community. Finally, the proposed solution is validated through experimental results, where difficulties include inconsistent wind, uneven terrain, and sandy conditions.
- 19 December 2017
- Published by SAGE Publications in The International Journal of Robotics Research
- Vol. 37 (9) , 1062-1084
Hold Or take Optimal Plan (HOOP): A quadratic programming approach to multi-robot trajectory generation
In this work, we present Hold Or take Optimal Plan (HOOP), a centralized trajectory generation algorithm for labeled multi-robot systems operating in obstacle-free, two-dimensional, continuous workspaces. Given a team of N robots, each with nth-order dynamics, our algorithm finds trajectories that navigate vehicles from their start positions to non-interchangeable goal positions in a collision-free manner. The algorithm operates in two phases. In the motion planning step, a geometric algorithm finds a collision-free, piecewise-linear trajectory for each robot. In the trajectory generation step, each robot’s trajectory is refined into a higher-order piecewise polynomial with a quadratic program. The novelty of our method is in this problem decomposition. The motion plan, through abstracting away robots’ dynamics, can be found quickly. It is then subsequently leveraged to construct collision avoidance constraints for N decoupled quadratic programs instead of a single, coupled optimization problem, decreasing computation time. We prove that this method is safe, complete, and generates smooth trajectories that respect robots’ dynamics. We demonstrate the algorithm’s practicality through extensive quadrotor experiments.
- 19 December 2017
- Published by SAGE Publications in The International Journal of Robotics Research
- Vol. 37 (9) , 1062-1084
Hold Or take Optimal Plan (HOOP): A quadratic programming approach to multi-robot trajectory generation
In this work, we present Hold Or take Optimal Plan (HOOP), a centralized trajectory generation algorithm for labeled multi-robot systems operating in obstacle-free, two-dimensional, continuous workspaces. Given a team of N robots, each with nth-order dynamics, our algorithm finds trajectories that navigate vehicles from their start positions to non-interchangeable goal positions in a collision-free manner. The algorithm operates in two phases. In the motion planning step, a geometric algorithm finds a collision-free, piecewise-linear trajectory for each robot. In the trajectory generation step, each robot’s trajectory is refined into a higher-order piecewise polynomial with a quadratic program. The novelty of our method is in this problem decomposition. The motion plan, through abstracting away robots’ dynamics, can be found quickly. It is then subsequently leveraged to construct collision avoidance constraints for N decoupled quadratic programs instead of a single, coupled optimization problem, decreasing computation time. We prove that this method is safe, complete, and generates smooth trajectories that respect robots’ dynamics. We demonstrate the algorithm’s practicality through extensive quadrotor experiments.
- Open Access
- 8 May 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 2 (3) , 1762-1769
Autonomous Flight for Detection, Localization, and Tracking of Moving Targets With a Small Quadrotor
In this letter, we address the autonomous flight of a small quadrotor, enabling tracking of a moving object. The 15-cm diameter, 250-g robot relies only on onboard sensors (a single camera and an inertial measurement unit) and computers, and can detect, localize, and track moving objects. Our key contributions include the relative pose estimate of a spherical target as well as the planning algorithm, which considers the dynamics of the underactuated robot, the actuator limitations, and the field of view constraints. We show simulation and experimental results to demonstrate feasibility and performance, as well as robustness to abrupt variations in target motion.
- 8 May 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 2 (3) , 1762-1769
Open AccessAutonomous Flight for Detection, Localization, and Tracking of Moving Targets With a Small Quadrotor
In this letter, we address the autonomous flight of a small quadrotor, enabling tracking of a moving object. The 15-cm diameter, 250-g robot relies only on onboard sensors (a single camera and an inertial measurement unit) and computers, and can detect, localize, and track moving objects. Our key contributions include the relative pose estimate of a spherical target as well as the planning algorithm, which considers the dynamics of the underactuated robot, the actuator limitations, and the field of view constraints. We show simulation and experimental results to demonstrate feasibility and performance, as well as robustness to abrupt variations in target motion.
- 21 March 2017
- Published by Springer Nature
- p. 586-598
Safe Navigation of Quadrotor Teams to Labeled Goals in Limited Workspaces
- 21 March 2017
- Published by Springer Nature
- p. 586-598
Safe Navigation of Quadrotor Teams to Labeled Goals in Limited Workspaces
- 8 March 2017
- Published by SPIE-Intl Soc Optical Eng in SPIE Newsroom
Autonomous perching and grasping for micro aerial vehicles
- 8 March 2017
- Published by SPIE-Intl Soc Optical Eng in SPIE Newsroom
Autonomous perching and grasping for micro aerial vehicles
- 1 December 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1806-1813
Bearing-only formation control with auxiliary distance measurements, leaders, and collision avoidance
We address the controller synthesis problem for distributed formation control. Our solution requires only relative bearing measurements (as opposed to full translations), and is based on the exact gradient of a Lyapunov function with only global minimizers (independently from the formation topology). These properties allow a simple proof of global asymptotic convergence, and extensions for including distance measurements, leaders and collision avoidance. We validate our approach through simulations and comparison with other stateof-the-art algorithms.
- 1 December 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1806-1813
Bearing-only formation control with auxiliary distance measurements, leaders, and collision avoidance
We address the controller synthesis problem for distributed formation control. Our solution requires only relative bearing measurements (as opposed to full translations), and is based on the exact gradient of a Lyapunov function with only global minimizers (independently from the formation topology). These properties allow a simple proof of global asymptotic convergence, and extensions for including distance measurements, leaders and collision avoidance. We validate our approach through simulations and comparison with other stateof-the-art algorithms.
- 1 August 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Control Systems
- Vol. 36 (4) , 22-44
A Distributed Optimization Framework for Localization and Formation Control: Applications to Vision-Based Measurements
Multiagent systems have been a major area of research for the last 15 years. This interest has been motivated by tasks that can be executed more rapidly in a collaborative manner or that are nearly impossible to carry out otherwise. To be effective, the agents need to have the notion of a common goal shared by the entire network (for instance, a desired formation) and individual control laws to realize the goal. The common goal is typically centralized, in the sense that it involves the state of all the agents at the same time. On the other hand, it is often desirable to have individual control laws that are distributed, in the sense that the desired action of an agent depends only on the measurements and states available at the node and at a small number of neighbors. This is an attractive quality because it implies an overall system that is modular and intrinsically more robust to communication delays and node failures.
- 1 August 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Control Systems
- Vol. 36 (4) , 22-44
A Distributed Optimization Framework for Localization and Formation Control: Applications to Vision-Based Measurements
Multiagent systems have been a major area of research for the last 15 years. This interest has been motivated by tasks that can be executed more rapidly in a collaborative manner or that are nearly impossible to carry out otherwise. To be effective, the agents need to have the notion of a common goal shared by the entire network (for instance, a desired formation) and individual control laws to realize the goal. The common goal is typically centralized, in the sense that it involves the state of all the agents at the same time. On the other hand, it is often desirable to have individual control laws that are distributed, in the sense that the desired action of an agent depends only on the measurements and states available at the node and at a small number of neighbors. This is an attractive quality because it implies an overall system that is modular and intrinsically more robust to communication delays and node failures.