Márcio Muniz de Farias
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Márcio Muniz de Farias has a total of 123 co-authors. Here are the top co-authors by number of shared publications:
- Manoel Porfírio Cordão Neto
Universidade de Brasília, Brasília, Brazil
7 shared publications - Roberto Roselló Valera
Center of Computational Mechanics and Numerical Methods in Engineering, CIMNE-UCLV Classroom, Central University of Las Villas, Santa Clara, Cuba
7 shared publications - Eugenio Oñate
Centre Internacional de Mètodes Numèrics a l’Enginyeria (CIMNE), Barcelona, Spain
6 shared publications - Irvin Pérez Morales
Center of Computational Mechanics and Numerical Methods in Engineering, CIMNE-UCLV Classroom, Central University of Las Villas, Santa Clara, Cuba
6 shared publications - Luiz Guilherme Rodrigues de Mello
Departamento Nacional de Infraestrutura de transportes
6 shared publications - Hugo Alexander Rondón-Quintana
Universidad Distrital Francisco José de Caldas
5 shared publications
Latest Publications
- 17 October 2026
- Published by Springer Nature in Transportation Infrastructure Geotechnology
- Vol. 13 (8) , 312
Modeling High-Viscosity Diatomaceous Soils via a Modified Cam-Clay Framework
- 17 October 2026
- Published by Springer Nature in Transportation Infrastructure Geotechnology
- Vol. 13 (8) , 312
Modeling High-Viscosity Diatomaceous Soils via a Modified Cam-Clay Framework
- Open Access
- 7 October 2026
- Published by Springer Nature in International Journal of Pavement Research and Technology
- p. 1-23
In Situ Instrumentation and Calibration of Flexible Pavement Under Real Traffic: Experimental Comparison with the AEMC/MeDiNa Model in Brazil
This article presents the design, calibration and field evaluation of an instrumented flexible pavement section aimed at quantifying mechanical responses and comparing them with the predictions of multilayer elastic analysis (AEMC), the mechanistic component of the Brazilian mechanistic-empirical method MeDiNa. Total earth pressure cells and strain gauges were installed in the asphalt layer, base, sub-base and subgrade to monitor stresses and strains under a controlled loading protocol ranging from 0 to 100% of the 8.2-ton standard axle load, to evaluate conversion factors and verify the metrological stability of the measurements. The results showed physically consistent time histories, with progressive response reduction as the load decreased, spatial sensitivity to wheel path position and stress attenuation with depth. In the model-to-field comparison, the assumptions of full and partial interlayer bonding generally provided better agreement with the measured data than the unbonded scenario, although magnitude discrepancies persisted for some stresses and strains. From an operational standpoint, the study highlighted the critical influence of sensor integrity and redundancy, cable and connection protection and vehicle trajectory control on data quality. As a contribution, the work provides experimental evidence for the evaluation of AEMC/MeDiNa in the Brazilian context and organizes practical recommendations for future instrumentation campaigns and for strengthening the regional calibration of the method.
- 7 October 2026
- Published by Springer Nature in International Journal of Pavement Research and Technology
- p. 1-23
Open AccessIn Situ Instrumentation and Calibration of Flexible Pavement Under Real Traffic: Experimental Comparison with the AEMC/MeDiNa Model in Brazil
This article presents the design, calibration and field evaluation of an instrumented flexible pavement section aimed at quantifying mechanical responses and comparing them with the predictions of multilayer elastic analysis (AEMC), the mechanistic component of the Brazilian mechanistic-empirical method MeDiNa. Total earth pressure cells and strain gauges were installed in the asphalt layer, base, sub-base and subgrade to monitor stresses and strains under a controlled loading protocol ranging from 0 to 100% of the 8.2-ton standard axle load, to evaluate conversion factors and verify the metrological stability of the measurements. The results showed physically consistent time histories, with progressive response reduction as the load decreased, spatial sensitivity to wheel path position and stress attenuation with depth. In the model-to-field comparison, the assumptions of full and partial interlayer bonding generally provided better agreement with the measured data than the unbonded scenario, although magnitude discrepancies persisted for some stresses and strains. From an operational standpoint, the study highlighted the critical influence of sensor integrity and redundancy, cable and connection protection and vehicle trajectory control on data quality. As a contribution, the work provides experimental evidence for the evaluation of AEMC/MeDiNa in the Brazilian context and organizes practical recommendations for future instrumentation campaigns and for strengthening the regional calibration of the method.
- 9 July 2026
- Published by Springer Nature
- p. 223-229
Rheological and Mechanical Enhancement of Asphalt Binders Using Recycled Low-Density Polyethylene (LDPE)
- 9 July 2026
- Published by Springer Nature
- p. 223-229
Rheological and Mechanical Enhancement of Asphalt Binders Using Recycled Low-Density Polyethylene (LDPE)
- Open Access
- 4 July 2026
- Published by MDPI AG in Sustainability
- Vol. 18 (13) , 6813
Mechanical Behavior of a Hot-Mix Asphalt with the Addition of Water Treatment Sludge (WTS) for Sustainable Pavement Application
Drinking water treatment plants produce large quantities of Water Treatment Sludge (WTS), which negatively impacts the environment due to improper disposal. In this study, the mechanical performance of a hot-mix asphalt (HMA) containing WTS (referred to as HMA WTS) was evaluated and compared with a control mixture (HMA C), with a primary focus on its potential application in pavements constructed in warm-climate regions. In this way, the implementation of sustainable practices in road construction is promoted. The WTS was physicochemical characterized. Subsequently, the WTS was calcined at 200, 300, 500, and 800 °C to transform it into ash for use as filler (F). A calcination temperature of 500 °C was selected as optimal, based on the evaluation of the physical properties of mastic samples prepared with asphalt cement (AC) and calcined WTS. F/AC ratios of 0.11, 0.25, 0.43, and 0.67 were used, corresponding to filler contents between 0.5% and 2% in the HMA. Based on the stiffness and workability of the asphalt mastic, an F/AC ratio of 0.25 was selected, representing 1.0% filler in the HMA. Two mix designs (HMA C and HMA WTS) were developed according to the Marshall methodology to determine the Optimum Asphalt Content (OAC). Mechanical performance and durability tests were conducted to evaluate the behavior of the asphalt mixtures. The results indicate that WTS increased mastic stiffness, enhancing the mechanical performance of the HMA (greater resistance under monotonic loading and improved rutting and fatigue resistance) while reducing OAC, thus representing a promising alternative for its management and final disposal and contributes to sustainability in pavement engineering. However, durability-related properties (resistance to moisture damage, raveling, and abrasion) decreased due to the reduction in OAC.
- 4 July 2026
- Published by MDPI AG in Sustainability
- Vol. 18 (13) , 6813
Open AccessMechanical Behavior of a Hot-Mix Asphalt with the Addition of Water Treatment Sludge (WTS) for Sustainable Pavement Application
Drinking water treatment plants produce large quantities of Water Treatment Sludge (WTS), which negatively impacts the environment due to improper disposal. In this study, the mechanical performance of a hot-mix asphalt (HMA) containing WTS (referred to as HMA WTS) was evaluated and compared with a control mixture (HMA C), with a primary focus on its potential application in pavements constructed in warm-climate regions. In this way, the implementation of sustainable practices in road construction is promoted. The WTS was physicochemical characterized. Subsequently, the WTS was calcined at 200, 300, 500, and 800 °C to transform it into ash for use as filler (F). A calcination temperature of 500 °C was selected as optimal, based on the evaluation of the physical properties of mastic samples prepared with asphalt cement (AC) and calcined WTS. F/AC ratios of 0.11, 0.25, 0.43, and 0.67 were used, corresponding to filler contents between 0.5% and 2% in the HMA. Based on the stiffness and workability of the asphalt mastic, an F/AC ratio of 0.25 was selected, representing 1.0% filler in the HMA. Two mix designs (HMA C and HMA WTS) were developed according to the Marshall methodology to determine the Optimum Asphalt Content (OAC). Mechanical performance and durability tests were conducted to evaluate the behavior of the asphalt mixtures. The results indicate that WTS increased mastic stiffness, enhancing the mechanical performance of the HMA (greater resistance under monotonic loading and improved rutting and fatigue resistance) while reducing OAC, thus representing a promising alternative for its management and final disposal and contributes to sustainability in pavement engineering. However, durability-related properties (resistance to moisture damage, raveling, and abrasion) decreased due to the reduction in OAC.
- Open Access
- 16 March 2026
- Published by Associacao Nacional de Pesquisa e Ensino em Transportes in Transportes
- Vol. 34, e3090
Desempenho de pavimentos asfálticos: comparação entre previsões MeDiNa, ensaios HVS e dados de tráfego real
A previsão do desempenho de pavimentos asfálticos é uma tarefa complexa da Engenharia de Pavimentos, exigindo ensaios laboratoriais e bancos de dados de trechos experimentais capazes de captar a parcela empírica do comportamento estrutural. Assim, esta pesquisa avaliou três segmentos experimentais implantados na BR-116, no Rio Grande do Sul, denominados A, B e C, distintos pelo tipo de ligante asfáltico (CAP 50/70, AMP 55/75 e AMP 60/85) e pela espessura do revestimento (5 cm nos segmentos A e B e 14 cm no segmento C). Os segmentos foram solicitados pelo tráfego real e por um simulador do tipo Heavy Vehicle Simulator (HVS). Também foram realizados ensaios laboratoriais para determinação de parâmetros de rigidez e dano, permitindo a aplicação do Método de Dimensionamento Nacional (MeDiNa). A evolução da fadiga em campo foi comparada às curvas obtidas a partir da porcentagem de área trincada simulada no MeDiNa. O Segmento B apresentou melhor compatibilidade entre as metodologias. Nos segmentos A e C observaram-se divergências entre os resultados do HVS, tráfego real e MeDiNa. Assim, não houve compatibilidade global entre as abordagens, indicando a necessidade de aprimoramento do protocolo de utilização do simulador, possivelmente associada às condições climáticas locais e à natureza da solicitação.
- 16 March 2026
- Published by Associacao Nacional de Pesquisa e Ensino em Transportes in Transportes
- Vol. 34, e3090
Open AccessDesempenho de pavimentos asfálticos: comparação entre previsões MeDiNa, ensaios HVS e dados de tráfego real
A previsão do desempenho de pavimentos asfálticos é uma tarefa complexa da Engenharia de Pavimentos, exigindo ensaios laboratoriais e bancos de dados de trechos experimentais capazes de captar a parcela empírica do comportamento estrutural. Assim, esta pesquisa avaliou três segmentos experimentais implantados na BR-116, no Rio Grande do Sul, denominados A, B e C, distintos pelo tipo de ligante asfáltico (CAP 50/70, AMP 55/75 e AMP 60/85) e pela espessura do revestimento (5 cm nos segmentos A e B e 14 cm no segmento C). Os segmentos foram solicitados pelo tráfego real e por um simulador do tipo Heavy Vehicle Simulator (HVS). Também foram realizados ensaios laboratoriais para determinação de parâmetros de rigidez e dano, permitindo a aplicação do Método de Dimensionamento Nacional (MeDiNa). A evolução da fadiga em campo foi comparada às curvas obtidas a partir da porcentagem de área trincada simulada no MeDiNa. O Segmento B apresentou melhor compatibilidade entre as metodologias. Nos segmentos A e C observaram-se divergências entre os resultados do HVS, tráfego real e MeDiNa. Assim, não houve compatibilidade global entre as abordagens, indicando a necessidade de aprimoramento do protocolo de utilização do simulador, possivelmente associada às condições climáticas locais e à natureza da solicitação.
- Open Access
- 2 January 2026
- Published by Brazilian Journals in Caderno Pedagógico
- Vol. 23 (1) , e22823
Numerical modeling of flow in porous media via lattice Boltzmann and discrete element methods
This paper aims to perform a two-dimensional study of flow in porous media through the implementation of a computational code based on the Lattice Boltzmann and Discrete Element methods, coupled using the immersed moving boundary technique. The Lattice Boltzmann Method employs a D2Q9 lattice and both BGK and MRT collision operators, while the Discrete Element Method is implemented using a linear interaction model between particles. The code was validated using classical benchmark problems, including the lid-driven cavity flow and fluid flow around a circular cylinder. Simulations were carried out for porous media composed of disk-shaped particles with uniform and random distributions, as well as realistic particle geometries. The formation of preferential flow paths was investigated, and the numerical permeability obtained from the simulations was compared with the Ergun and Kozeny–Carman equations, showing excellent numerical agreement. The results demonstrate that the developed code is a robust and efficient tool for simulating fluid–solid interactions in porous media.
- 2 January 2026
- Published by Brazilian Journals in Caderno Pedagógico
- Vol. 23 (1) , e22823
Open AccessNumerical modeling of flow in porous media via lattice Boltzmann and discrete element methods
This paper aims to perform a two-dimensional study of flow in porous media through the implementation of a computational code based on the Lattice Boltzmann and Discrete Element methods, coupled using the immersed moving boundary technique. The Lattice Boltzmann Method employs a D2Q9 lattice and both BGK and MRT collision operators, while the Discrete Element Method is implemented using a linear interaction model between particles. The code was validated using classical benchmark problems, including the lid-driven cavity flow and fluid flow around a circular cylinder. Simulations were carried out for porous media composed of disk-shaped particles with uniform and random distributions, as well as realistic particle geometries. The formation of preferential flow paths was investigated, and the numerical permeability obtained from the simulations was compared with the Ergun and Kozeny–Carman equations, showing excellent numerical agreement. The results demonstrate that the developed code is a robust and efficient tool for simulating fluid–solid interactions in porous media.
- Open Access
- 2 July 2025
- Published by Brazilian Journals in REVISTA FOCO
- Vol. 18 (7) , e9232
ROAD INFRASTRUCTURE ADOPTING SIDERURGICAL AND ORNAMENTAL STONE INDUSTRUIAL RESIDUES
The integration of industrial residues such as steel slag (SS) into rorad construction have been presenting significant opportunities for enhancing infrastructure performance and sustainability. Similarly, ornamental stone processing residue (OSR) might tread the same engineering and scientific path of the SS. Advances in industrial residue (IR) characterization, including detailed measurement of its component levels, enable the development of targeted IR utilization strategies that may reduce project life cycle cost, reduce the use of natural raw materials (NRM), and enhance engineering properties of construction geomaterials. This work aim to demonstrate and correlate the use of OSR and SS in enhancing the sustainability and performance of road infrastructure applications, reviewing details of the transformation of these residues from waste streams into valuable components for highway and road engineering. The discussion encompasses the examination of the physical, chemical, and mechanical characteristics of SS and OSR, especially mixed with soils for geotechnical applications, underpinning their suitability for earthworks, soil stabilization, fills, and incorporation into base, sub-base, and pavement layers. The review covers a general view of the impact of OSR and SS on geotechnical properties such as density, plasticity, and strength, as well as their performance as a filler or aggregate substitute. By synthesizing current knowledge and the current practical applications, this paper demonstrates the engineering viability and the importance of integrating OSR into road construction, as well as SS is currently integrated, thereby addressing waste management challenges, conserving natural resources, and advancing sustainable development in geotechnical infrastructure projects.
- 2 July 2025
- Published by Brazilian Journals in REVISTA FOCO
- Vol. 18 (7) , e9232
Open AccessROAD INFRASTRUCTURE ADOPTING SIDERURGICAL AND ORNAMENTAL STONE INDUSTRUIAL RESIDUES
The integration of industrial residues such as steel slag (SS) into rorad construction have been presenting significant opportunities for enhancing infrastructure performance and sustainability. Similarly, ornamental stone processing residue (OSR) might tread the same engineering and scientific path of the SS. Advances in industrial residue (IR) characterization, including detailed measurement of its component levels, enable the development of targeted IR utilization strategies that may reduce project life cycle cost, reduce the use of natural raw materials (NRM), and enhance engineering properties of construction geomaterials. This work aim to demonstrate and correlate the use of OSR and SS in enhancing the sustainability and performance of road infrastructure applications, reviewing details of the transformation of these residues from waste streams into valuable components for highway and road engineering. The discussion encompasses the examination of the physical, chemical, and mechanical characteristics of SS and OSR, especially mixed with soils for geotechnical applications, underpinning their suitability for earthworks, soil stabilization, fills, and incorporation into base, sub-base, and pavement layers. The review covers a general view of the impact of OSR and SS on geotechnical properties such as density, plasticity, and strength, as well as their performance as a filler or aggregate substitute. By synthesizing current knowledge and the current practical applications, this paper demonstrates the engineering viability and the importance of integrating OSR into road construction, as well as SS is currently integrated, thereby addressing waste management challenges, conserving natural resources, and advancing sustainable development in geotechnical infrastructure projects.
- 24 April 2025
- Published by Springer Nature in Granular Matter
- Vol. 27 (3) , 1-16
Shape properties validation of virtual 3D particles created from AIMS 2D images for railway ballast DEM modeling
- 24 April 2025
- Published by Springer Nature in Granular Matter
- Vol. 27 (3) , 1-16
Shape properties validation of virtual 3D particles created from AIMS 2D images for railway ballast DEM modeling
- 24 December 2024
- Published by Springer Nature
- p. 373-377
Assessing the Effects of Waste Polyethylene Terephthalate Oligomer (WPETO)-Modified Asphalt Binder on Rheological Behavior
- 24 December 2024
- Published by Springer Nature
- p. 373-377
Assessing the Effects of Waste Polyethylene Terephthalate Oligomer (WPETO)-Modified Asphalt Binder on Rheological Behavior