MKMinJu Kim

MinJu Kim

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


MinJu Kim has a total of 11 co-authors. Here are the top co-authors by number of shared publications:

  • Jin-Soo Ahn

    Department of Dental Biomaterials Science and Dental Research Institute, School of Dentistry, Seoul National University, Seoul, Republic of Korea

    2 shared publications
  • Sungwon Ju

    Dental Research Institute and Department of Dental Biomaterials Science, School of Dentistry, Seoul National University, 101 Daehak-ro, Jongro-gu, Seoul 03080, Korea

    2 shared publications
  • B. Kollbe Ahn

    Marine Science Institute, University of California, Santa Barbara, California 93106, United States

    1 shared publication
  • Enji Cheon

    Dental Research Institute and Department of Dental Biomaterials Science, School of Dentistry, Seoul National University, 101 Daehak-ro, Jongno-gu, Seoul 03080, Korea

    1 shared publication
  • Hyon-Seok Jang

    Department of Oral and Maxillofacial Surgery, Korea University Graduate School of Clinical Dentistry, Seoul, Republic of Korea

    1 shared publication
  • Jinsoo Ahn

    Dental Research Institute and Department of Dental Biomaterials Science, Seoul National University School of Dentistry, Seoul 03080, South Korea

    1 shared publication

Latest Publications

  • Open Access

    Gemini-Mediated Self-Disinfecting Surfaces to Address the Contact Transmission of Infectious Diseases

    by MinJu Kim, Roscoe T. H. Linstadt, Kollbe Ahn Ando, Jinsoo Ahn

    According to both the Center for Disease Control and the World Health Organization, contact transmission is the primary transmission route of infectious diseases worldwide. Usually, this is mitigated by a schedule of repeated regular sanitization, yet surfaces are easily re-contaminated in the interim between cleanings. One solution to this problem is to generate self-disinfecting surfaces that can display sustained virucidal/antimicrobial properties against pathogens that settle upon them. Quaternary ammonium organosilicon compounds are ideal candidates to achieve this; cationic surfactants are safe and well-established surface disinfectants, while organosilanes are used broadly to form durable coatings with altered surface properties on many different materials. Despite their potential to circumvent the disadvantages of traditional disinfection methods, extant commercially available quaternary ammonium silanes do not display comparable efficacy to the standard surface disinfectants, nor have their respective coatings been demonstrated to meet the Environmental Protection Agency’s guidelines for residual/extended efficacy. Inspired by the powerful surface activity of double-headed “gemini” surfactants, here, we present gemini-diquaternary silanes (GQs) with robust residual germicidal efficacy on various surfaces by incorporating a second cationic “head” to the structure of a conventional monoquaternary ammonium silane (MQ). Aqueous solutions of GQs were tested in suspension- and surface-antimicrobial assays against an array of pathogens, including Staphylococcus aureus, Escherichia coli, Pseudomonas aeruginosa, and severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). GQ performance was benchmarked against the common disinfectants, ethanol, hydrogen peroxide, hypochlorite, as well as MQ. Solutions of GQs were efficacious when used for immediate disinfection (>106-fold reduction in 15 s). Additionally, GQs were demonstrated to impart durable self-disinfecting properties to a variety of porous and nonporous surfaces, effective after repeated cycles of abrasion and repeated contaminations, and with superior coating ability and activity (>108 higher activity) than that of MQs. GQs as surface treatments show great promise to overcome the limitations of traditional disinfectants in preventing the spread of infectious diseases.


  • Open Access

    Direct Measurement of Heat Produced during Drilling for Implant Site Preparation

    by Yongsoo Kim, Sungwon Ju, MinJu Kim, Minsu Park, Sangho Jun, Jinsoo Ahn

    The aim of this study was to directly measure the temperature of the drill during implant site preparation. The measured temperature was compared to that previously reported inside the bone. The temperature change of the drill was measured using a thermocouple inserted inside the stainless steel drill using an 18-gauge needle and mercury-containing slip ring. Three thermocouples were inserted into the bone with different depths of 10 mm, 5 mm and 1 mm. The thermocouple was 0.5 mm away from the periphery of the drilled hole with a diameter of 3.4 mm. The drill rotating speed varied from 500 rpm to 2000 rpm. Each drilling procedure was performed 10 times, and the average was calculated. The temperature of the drill increased rapidly, and the thermocouples in the bone reached a maximum temperature after the drill temperature started to decrease. The maximum inner temperature of the bone was the highest at a depth of 10 mm. The patterns of the temperature change were similar at different rotating speeds. The actual maximum temperature at the drill and bone interface was significantly higher than the temperature measured inside the bone in previous reports.


  • Open Access

    The Stability of Temporary Restorations Fabricated on a Healing Cap for Immediate Loading: An In Vitro Study

    by Sangho Jun, Hyonseok Jang, Enji Cheon, MinJu Kim, Sungwon Ju, Jinsoo Ahn

    The aim of this study was to analyze the load distribution of interim restorations using healing cap during immediate loading implant treatment in vitro. A total of 29 models with interim restorations which were fabricated with healing cap were selected. The pull-out strength was measured with a used healing cap and new healing cap. The compressive strength and sinking distance were also measured. The pull-out strength of interim restoration showed lower value (max. 29.8 N) compared to the natural bite force. The sinking amounts were larger than normal tooth sinking. The sinking amounts of interim restorations fabricated on a healing cap were roughly 3 times (0.3–0.5 mm under 450 N) those of normal teeth. The interim restoration on plastic healing cap would be useful for immediate loading implant treatment.