GCGuoming Chen

Guoming Chen

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Guoming Chen has a total of 35 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Wear-Resistant Boronizing for 17-4PH Components of Fluid Pump

    by Yongchao Chen, Guoming Chen, Chang Du, Kang Liu

    The fluid pump was the key component of the formation tester; the pump cylinder, piston, and piston rod of the fluid pump often suffer from wear scratches and seal failure, which greatly reduces the service reliability of the instrument. To improve the wear resistance of the fluid pump, 17-4PH steel specimens were treated by boronizing at 750 °C for 20 h. Specimens with and without boronizing were studied by OM, SEM, XRD, microhardness test, and wear resistance test. Layers of about 60 μm thickness formed during boronization contain a mixture of FeB, CrB, and α(B)-Fe phases, which leads to a significant improvement in microhardness (from 336 to 980 HV) and wear rate (from 16.4 × 10−5 mm3/Nm to 3.3 × 10−5 mm3/Nm). The pump cylinder and the fluid-pump piston rod were boronized and assembled into the pumping module, which passed the indoor durability test for 90 h and did not show obvious surface wear after 60 h of field experience. For the first time, the boronization process extends the service time of the fluid pump, improving the wear resistance of the pump cylinder and piston rod.


  • Open Access

    Experimental and Numerical Study for Gas Release and Dispersion on Offshore Platforms

    by Fengpu Xiao, Yanan Li, Jun Zhang, Hai Dong, Dongdong Yang, Guoming Chen

    Accidental gas release is a major triggering event for the offshore oil and gas industry. This paper focuses on the experimental and numerical investigation for dispersion behavior of released gas on offshore platforms. For this purpose, an experimental system is designed and developed to investigate gas release and dispersion. A series of experiments are carried out, among which the scenarios with constant leakage rates and time-varying leakage rates are both emphasized. The gas concentrations at different sampling points are obtained to study the dispersion behavior and accumulation characteristics of the released gas. Furthermore, a numerical computational fluid dynamics model is established to replicate the experimental scenarios. Good agreement between experimental data and CFD simulation results is observed by calculating a series of statistical performance measures. The developed numerical model is subsequently utilized to investigate a gas release scenario on a practical offshore platform, in which a fully transient leakage rate is adopted considering the response of process protection measures. The developed numerical model could provide support for risk assessment and optimization of contingency plans against gas release accidents in offshore facilities.


  • Open Access

    Modeling the Evolution of Major Storm-Disaster-Induced Accidents in the Offshore Oil and Gas Industry

    by Gaogeng Zhu, Guoming Chen, Jingyu Zhu, Xiangkun Meng, Xinhong Li

    Storm disasters are the most common cause of accidents in offshore oil and gas industries. To prevent accidents resulting from storms, it is vital to analyze accident propagation and to learn about accident mechanism from previous accidents. In this paper, a novel risk analysis framework is proposed for systematically identifying and analyzing the evolution of accident causes. First, accident causal factors are identified and coded based on grounded theory (GT). Then, decision making trial and evaluation laboratory (DEMATEL) is integrated with interpretative structural modeling (ISM) to establish accident evolution hierarchy. Finally, complex networks (CN) are developed to analyze the evolution process of accidents. Compared to reported works, the contribution is threefold: (1) the demand for expert knowledge and personnel subjective influence are reduced through the data induction of accident cases; (2) the method of establishing influence matrix and interaction matrix is improved according to the accident frequency analysis; (3) a hybrid algorithm that can calculate multiple shortest paths of accident evolution under the same node pair is proposed. This method provides a new idea for step-by-step assessment of the accident evolution process, which weakens the subjectivity of traditional methods and achieves quantitative assessment of the importance of accident evolution nodes. The proposed method is demonstrated and validated by a case study of major offshore oil and gas industry accidents caused by storm disasters. Results show that there are five key nodes and five critical paths in the process of accident evolution. Through targeted prevention and control of these nodes and paths, the average shortest path length of the accident evolution network is increased by 35.19%, and the maximum global efficiency decreases by 20.12%. This indicates that the proposed method has broad applicability and can effectively reduce operational risk, so that it can guide actual offshore oil and gas operations during storm disasters.


  • Open Access

    Identification of Tiny Surface Cracks in a Rugged Weld by Signal Gradient Algorithm Using the ACFM Technique

    by Xin’an Yuan, Wei Li, Xiaokang Yin, Guoming Chen, Jianming Zhao, Weiyu Jiang, Jiuhao Ge

    It is still a big challenge to identify tiny surface cracks in a rugged weld due to the lift-off variations using the nondestructive testing (NDT) method. In this paper, the signal gradient algorithm is presented to identify the tiny surface crack in the rugged weld using the alternating current field measurement (ACFM) technique. The ACFM simulation model and testing system was set up to obtain the insensitive signal to the lift-off variations. The signal gradient algorithm was presented to process the insensitive signal for the identification of the tiny surface crack in the rugged weld. The results show that the Bz signal is the insensitive signal to lift-off variations caused by the rugged weld. The signal to noise ratio (SNR) of the crack identification signal was greatly improved by the signal gradient algorithm, and a tiny surface crack can be identified effectively in the weld and the heat affected zone (HAZ).


  • Open Access

    Further Investigations into the Capacitive Imaging Technique Using a Multi-Electrode Sensor

    by Zhen Li, Guoming Chen, Yue Gu, Kefan Wang, Wei Li, Xiaokang Yin

    As a novel non-destructive testing technique, capacitive imaging (CI) has been used to detect defects within the insulation layer and metal surface of an insulated metallic structure, that is, pipe or vessel. Due to the non-linearity of the probing field, the defects at different depths in the insulation layer are difficult to compare accurately using the conventional CI sensor with a single pair of electrodes. In addition, the conventional CI sensor cannot provide adequate information to discriminate the defects in the insulation layer and metal surface. In order to solve the above-mentioned problems, the multi-electrode sensor is introduced. The multi-electrode sensor uses multiple quasi-static fringing electric fields generated by an array of coplanar electrodes to obtain extra information about the defects in the specimen. In this work, the feasibility of multiple quasi-static electric fields detecting the defects was demonstrated and the Measurement Sensitivity Distributions (MSDs) of the multi-electrode sensor detecting the defects were acquired using the FEM models. The simulation and experimental results show that the Dynamic Change Rates (DCRs) of the measured values obtained at the center of the defects in the insulator layer and metal surface present different variation patterns, which can be used to discriminate these two different kinds of defects. The reasons for the different variation patterns of DCRs were explained by the changing trends of MSDs with increased electrode separation. In addition, it was demonstrated that the different depths of the defects in the insulator layer can be compared accurately by comprehensive analysis of the detection results from all the electrode pairs.


  • Open Access

    Enhancing the Visibility of Delamination during Pulsed Thermography of Carbon Fiber-Reinforced Plates Using a Stacked Autoencoder

    by Changhang Xu, Jing Xie, Changwei Wu, Lemei Gao, Guoming Chen, Gangbing Song

    The effectiveness of pulsed thermography (PT) for detecting delamination in carbon fiber-reinforced polymer (CFRP) plates has been widely verified. However, delaminations are usually characterized by weak visibility due to the influences of inspection factors and the delaminations with weak visibility are easily missed in real inspections. In this study, by introducing a deep learning algorithm—stacked autoencoder (SAE)—to PT, we propose a novel approach (SAE-PT) to enhance the visibility of delaminations. Based on the ability of SAE to learn unsupervised features from data, the thermal features of delaminations are extracted from the raw thermograms. The extracted features are then employed to construct SAE images, in which the visibility of delaminations is expected to be enhanced. To test the performance of SAE-PT, we inspected CFRP plates with prefabricated delaminations. By implementing SAE-PT on the raw inspection data, the delaminations were more clearly indicated in the constructed SAE images. We also compare SAE-PT to the widely used principal component thermography (PCT) method to further verify the validity of the proposed approach. The results reveal that compared to PCT, SAE-PT can show delaminations in CFRP with higher contrast. By effectively enhancing the delamination visibility, SAE-PT thus has potential for improving the inspection accuracy of PT for non-destructive testing (NDT) of CFRP.


  • Open Access

    Experimental Investigation on the Detection of Multiple Surface Cracks Using Vibrothermography with a Low-Power Piezoceramic Actuator

    by Changhang Xu, Jing Xie, Wuyang Zhang, Qingzhao Kong, Guoming Chen, Gangbing Song

    Vibrothermography often employs a high-power actuator to generate heat on a specimen to reveal damage, however, the high-power actuator brings inconvenience to the application and possibly introduces additional damage to the inspected objects. This study uses a low-power piezoceramic transducer as the actuator of vibrothermography and explores its ability to detect multiple surface cracks in a metal part. Experiments were conducted on a thin aluminum beam with three cracks in different orientations. Detailed analyses of both thermograms and temperature data are presented to validate the proposed vibrothermography method. To further investigate the performance of the proposed vibrothermography method, we experimentally studied the effects of several critical factors, including the amplitude of excitation signal, specimen constraints, relative position between the transducer and cracks (the transducer is mounted on the same or the opposite side with the cracks). The results demonstrate that all cracks can be detected conveniently and simultaneously by using the proposed low-power vibrothermography. We also found that the magnitude of excitation signal and the specimen constraints have a great influence on detection results. Combined with effective data processing methods, such as Fourier transformation employed in this study, the proposed method provides a promising potential to detect multiple cracks on a metal surface in a safe and effective manner.


  • Open Access

    An Investigation on Eddy Current Pulsed Thermography to Detect Surface Cracks on the Tungsten Carbide Matrix of Polycrystalline Diamond Compact Bit

    by Changhang Xu, Xumei Gong, Wuyang Zhang, Guoming Chen

    Polycrystalline diamond compact (PDC) bits are commonly used drill bits in the petroleum drilling industry. Cracks often occur on the surface of a bit, which may result in the unexpected suspension of the drilling operation, or even accidents. Therefore, the detection of surface cracks on PDC bits is of great importance to ensure continuous drilling operation and to prevent accidents. However, it is extremely difficult to detect such cracks by visual inspection or other traditional nondestructive testing (NDT) techniques due to the small size of cracks and the irregular geometry of bits. As one emerging NDT technique, eddy current pulsed thermography (ECPT) can instantly detect surface cracks on metal parts with irregular geometry. In this study, the feasibility of ECPT of detecting surface cracks on the tungsten carbide matrix of PDC bits was investigated. A successive scanning detection mode is proposed to detect surface cracks by using ECPT with a low power heating excitation unit and small-size coils. The influence of excitation duration on the detection result was also investigated. In addition, principal component analysis (PCA) was employed to process the acquired IR image sequences to improve detection sensitivity. Finally, the whole shape of a crack was restored with processed images containing varied cracks segments. Based on the experimental results, we conclude that the surface cracks on the tungsten carbide matrix of PDC bit can be detected effectively and conveniently by ECPT in scanning mode with the aid of PCA.