Xinze Zhao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Xinze Zhao has a total of 36 co-authors. Here are the top co-authors by number of shared publications:
- Xiang Xu
College of Mechanical and Power Engineering, China Three Gorges University, Yichang 443002, China
5 shared publications - Meiyun Zhao
Hubei Key Laboratory of Hydroelectric Machinery Design & Maintenace, China Three Gorges University, Yichang 443000, China
4 shared publications - Wanting Li
College of Mechanical and Power Engineering, China Three Gorges University, Yichang 443002, China
4 shared publications - Wei Yang
Innovation and Entrepreneurship College, China Three Gorges University, Yichang 443002, China
4 shared publications - Yang Li
College of Mechanical and Power Engineering, China Three Gorges University, Yichang 443002, China
4 shared publications - Nengqi Xiao
China Three Gorges University
2 shared publications
Latest Publications
- Open Access
Effects of Simulated Ambient Dust on Current-Carrying Tribological Characteristics of Carbon Brushes/Collector Rings
To elucidate the influence of ring-chamber dust on the current-carrying tribological behavior of the carbon brush/collector ring system in hydro-generators, D172 carbon brushes paired with 45 steel collector rings were employed as the research subjects. Current-carrying sliding friction tests were systematically conducted under varying concentrations of carbon powder, iron powder, and carbon–iron mixed powders. The evolution of friction coefficient, wear loss, wear rate, and contact resistance was analyzed in detail, while the worn carbon brush specimens were characterized using three-dimensional profilometry, scanning electron microscopy (SEM), and energy-dispersive X-ray spectroscopy (EDS). The results demonstrate that different wear debris powders, serving as third-body media, exert significant regulatory effects on both interfacial tribological and electrical conduction behaviors. Under the carbon powder condition, a relatively stable carbonaceous third-body layer readily forms at the interface, maintaining low friction coefficient and wear rate—both reaching their minima at 120 mg/min—thus demonstrating effective friction reduction and wear resistance. In contrast, iron powder conditions promote pronounced abrasive action induced by hard particles, which increases the friction coefficient, accelerates carbon brush wear, and deteriorates the interfacial contact state. For carbon–iron mixed powders, the friction and wear levels lie between those observed for pure carbon and pure iron powders; meanwhile, contact resistance decreases steadily with increasing powder supply rate, indicating relatively superior current-carrying stability. The study reveals that carbon powder primarily contributes positively through lubrication and interfacial protection, whereas iron powder exacerbates damage via particle plowing and contact disruption. The synergistic interaction between the two determines the evolution of the interfacial film layer and the resulting changes in electrical contact performance. These findings provide a theoretical basis for wear control and operational maintenance of carbon brush systems in hydro-generators.
Open AccessEffects of Simulated Ambient Dust on Current-Carrying Tribological Characteristics of Carbon Brushes/Collector Rings
To elucidate the influence of ring-chamber dust on the current-carrying tribological behavior of the carbon brush/collector ring system in hydro-generators, D172 carbon brushes paired with 45 steel collector rings were employed as the research subjects. Current-carrying sliding friction tests were systematically conducted under varying concentrations of carbon powder, iron powder, and carbon–iron mixed powders. The evolution of friction coefficient, wear loss, wear rate, and contact resistance was analyzed in detail, while the worn carbon brush specimens were characterized using three-dimensional profilometry, scanning electron microscopy (SEM), and energy-dispersive X-ray spectroscopy (EDS). The results demonstrate that different wear debris powders, serving as third-body media, exert significant regulatory effects on both interfacial tribological and electrical conduction behaviors. Under the carbon powder condition, a relatively stable carbonaceous third-body layer readily forms at the interface, maintaining low friction coefficient and wear rate—both reaching their minima at 120 mg/min—thus demonstrating effective friction reduction and wear resistance. In contrast, iron powder conditions promote pronounced abrasive action induced by hard particles, which increases the friction coefficient, accelerates carbon brush wear, and deteriorates the interfacial contact state. For carbon–iron mixed powders, the friction and wear levels lie between those observed for pure carbon and pure iron powders; meanwhile, contact resistance decreases steadily with increasing powder supply rate, indicating relatively superior current-carrying stability. The study reveals that carbon powder primarily contributes positively through lubrication and interfacial protection, whereas iron powder exacerbates damage via particle plowing and contact disruption. The synergistic interaction between the two determines the evolution of the interfacial film layer and the resulting changes in electrical contact performance. These findings provide a theoretical basis for wear control and operational maintenance of carbon brush systems in hydro-generators.
- Open Access
Effect of Polarity on Arc Ablation Behaviour and Damage Mechanisms of Brush/Slip Ring Contact Interfaces
To clarify the origin of asymmetric arc ablation in hydroelectric generator slip rings, a Steel 45/carbon current-carrying friction pair was selected to investigate the influence of current polarity on arc behaviour and interfacial damage. Static gap discharge tests (10 A) and dynamic tests (current density of 10 A/cm2, sliding velocity of 0.419 m/s) were performed to characterize polarity-dependent erosion behaviour. The results indicate that, under the steel(+)–carbon(−) condition, the arc exhibits unstable burst-like discharge accompanied by intense spark spattering. The carbon cathode experiences severe material loss due to the combined effects of cathode-spot heating, positive-ion bombardment, and molten metal droplet impact. The steel surface is characterized by nested erosion pits and spherical resolidified spatter particles, while the apparent ablation-affected area shows an overall increase with accumulated arc duration, with a more pronounced expansion observed at longer durations. Pronounced bidirectional material migration and interfacial elemental enrichment are observed under the steel(+)–carbon(−) configuration, resulting in an apparent net mass loss rate approximately 2.5 times higher than that under the steel(-)–carbon(+) configuration. The reversed steel(−)–carbon(+) configuration produces a spatially constrained and stable arc discharge, accompanied by a continuous remelted layer and network-like thermal-stress cracks on the steel surface. Polarity reversal changes the direction of the interfacial electric field and charged-particle migration, thereby regulating cathode electron emission, arc discharge behaviour, energy distribution in the near-electrode region, and bidirectional material migration across the interface. These results provide a theoretical basis for elucidating the polarity-dependent arc ablation mechanism of steel/carbon friction pairs and for optimizing polarity configuration and differentiated protection strategies for hydroelectric generator slip rings.
Open AccessEffect of Polarity on Arc Ablation Behaviour and Damage Mechanisms of Brush/Slip Ring Contact Interfaces
To clarify the origin of asymmetric arc ablation in hydroelectric generator slip rings, a Steel 45/carbon current-carrying friction pair was selected to investigate the influence of current polarity on arc behaviour and interfacial damage. Static gap discharge tests (10 A) and dynamic tests (current density of 10 A/cm2, sliding velocity of 0.419 m/s) were performed to characterize polarity-dependent erosion behaviour. The results indicate that, under the steel(+)–carbon(−) condition, the arc exhibits unstable burst-like discharge accompanied by intense spark spattering. The carbon cathode experiences severe material loss due to the combined effects of cathode-spot heating, positive-ion bombardment, and molten metal droplet impact. The steel surface is characterized by nested erosion pits and spherical resolidified spatter particles, while the apparent ablation-affected area shows an overall increase with accumulated arc duration, with a more pronounced expansion observed at longer durations. Pronounced bidirectional material migration and interfacial elemental enrichment are observed under the steel(+)–carbon(−) configuration, resulting in an apparent net mass loss rate approximately 2.5 times higher than that under the steel(-)–carbon(+) configuration. The reversed steel(−)–carbon(+) configuration produces a spatially constrained and stable arc discharge, accompanied by a continuous remelted layer and network-like thermal-stress cracks on the steel surface. Polarity reversal changes the direction of the interfacial electric field and charged-particle migration, thereby regulating cathode electron emission, arc discharge behaviour, energy distribution in the near-electrode region, and bidirectional material migration across the interface. These results provide a theoretical basis for elucidating the polarity-dependent arc ablation mechanism of steel/carbon friction pairs and for optimizing polarity configuration and differentiated protection strategies for hydroelectric generator slip rings.
- Open Access
- 13 May 2026
- Published by MDPI AG in Lubricants
- Vol. 14 (5) , 200
Friction and Wear Behavior of Graphite Inlay Lubrication Structures for Localized Rings with Spherical Friction Pairs
Conventional solid-inlay lubrication research has focused on the overall inlay layout and generalized lubrication effects; localized inlay lubrication enables precise release of the lubricant and rapid formation of a uniform and dense lubricant film. The aim of this study is to use a combination of simulations and experimentation to establish a localized spherical friction pair containing a filled-hole structure, so that optimal lubrication can be predicted accurately. We designed seven different kinds of localized annular band inlay axial tiles, with ratios of 10, 12, 15, 18, 20, 22, and 25; carried out a transient mechanical analysis through finite element software, comparing the equivalent stress and friction coefficient of the inlay tiles with different ratios; and conducted friction wear tests through a self-developed spherical wear test bench. The friction surfaces of the tested specimens were analyzed for sliding friction coefficients and wear, as well as by SEM surface and EDS analyses. The results show that the best mechanical properties and the smallest theoretical friction coefficients are obtained when the relative ratio of the ring diameter to inlay hole diameter is 25. This study provides a theoretical basis for the design of spherical solid-inlay lubrication structures in the region of the split-belt ring design.
- 13 May 2026
- Published by MDPI AG in Lubricants
- Vol. 14 (5) , 200
Open AccessFriction and Wear Behavior of Graphite Inlay Lubrication Structures for Localized Rings with Spherical Friction Pairs
Conventional solid-inlay lubrication research has focused on the overall inlay layout and generalized lubrication effects; localized inlay lubrication enables precise release of the lubricant and rapid formation of a uniform and dense lubricant film. The aim of this study is to use a combination of simulations and experimentation to establish a localized spherical friction pair containing a filled-hole structure, so that optimal lubrication can be predicted accurately. We designed seven different kinds of localized annular band inlay axial tiles, with ratios of 10, 12, 15, 18, 20, 22, and 25; carried out a transient mechanical analysis through finite element software, comparing the equivalent stress and friction coefficient of the inlay tiles with different ratios; and conducted friction wear tests through a self-developed spherical wear test bench. The friction surfaces of the tested specimens were analyzed for sliding friction coefficients and wear, as well as by SEM surface and EDS analyses. The results show that the best mechanical properties and the smallest theoretical friction coefficients are obtained when the relative ratio of the ring diameter to inlay hole diameter is 25. This study provides a theoretical basis for the design of spherical solid-inlay lubrication structures in the region of the split-belt ring design.
- Open Access
Research Status and Progress on the Current-Carrying Friction and Wear Performance of Conductive Slip Rings in Harsh Environments
With the rapid development of aerospace, industrial automation, and weapons manufacturing, the performance requirements for conductive slip rings have become more stringent, and their operating environments have become increasingly harsh, making the study of the effects of harsh environmental conditions on slip rings particularly important. This paper systematically reviews the effects of harsh environments on the current-carrying friction and wear behavior of slip rings, with a detailed discussion on the mechanisms by which environmental factors such as high temperature, humidity, corrosive gases, and vacuum influence the tribological properties of slip ring materials. Research has shown that these harsh environments significantly change the friction coefficient, wear rate, and electrical contact performance of slip rings, causing degradation of material properties. By reviewing current experimental studies and numerical simulations, this paper analyzes the performance variations and failure mechanisms of slip rings in various environments, summarizing the key technological progress in enhancing slip ring performance under such conditions, particularly the application of material modification and surface coating technologies. Additionally, concerning the lifetime prediction and monitoring of slip ring systems, this paper explores the potential of multiphysics simulation technology and intelligent monitoring methods. Finally, this paper looks forward to future research directions, including optimization design based on multiphysics simulation, the development of high-temperature coatings, the improvement of lifetime prediction models, and the optimization of thermal management strategies, aiming to provide theoretical support and technical guidance for enhancing the reliability and durability of slip rings in extreme environments.
Open AccessResearch Status and Progress on the Current-Carrying Friction and Wear Performance of Conductive Slip Rings in Harsh Environments
With the rapid development of aerospace, industrial automation, and weapons manufacturing, the performance requirements for conductive slip rings have become more stringent, and their operating environments have become increasingly harsh, making the study of the effects of harsh environmental conditions on slip rings particularly important. This paper systematically reviews the effects of harsh environments on the current-carrying friction and wear behavior of slip rings, with a detailed discussion on the mechanisms by which environmental factors such as high temperature, humidity, corrosive gases, and vacuum influence the tribological properties of slip ring materials. Research has shown that these harsh environments significantly change the friction coefficient, wear rate, and electrical contact performance of slip rings, causing degradation of material properties. By reviewing current experimental studies and numerical simulations, this paper analyzes the performance variations and failure mechanisms of slip rings in various environments, summarizing the key technological progress in enhancing slip ring performance under such conditions, particularly the application of material modification and surface coating technologies. Additionally, concerning the lifetime prediction and monitoring of slip ring systems, this paper explores the potential of multiphysics simulation technology and intelligent monitoring methods. Finally, this paper looks forward to future research directions, including optimization design based on multiphysics simulation, the development of high-temperature coatings, the improvement of lifetime prediction models, and the optimization of thermal management strategies, aiming to provide theoretical support and technical guidance for enhancing the reliability and durability of slip rings in extreme environments.
- Open Access
- 20 December 2024
- Published by MDPI AG in Lubricants
- Vol. 12 (12) , 461
Exploring the Effect of Interface Contact States on Brush/Ring Current-Carrying Friction
A carbon brush/collector ring set will have phenomena such as firing and ablation during operation, which is due to the existence of various abnormal contact modes of the brush/ring during operation, thus changing the carbon brush/collector ring interface state. To analyze the effects of different contact modes on the performance of the brush/ring, in this paper, we construct the contact modes of the air gap (loss of contact leads to the existence of a small gap between the two surfaces), direct contact (contact with abrasive particulate media), and surface porosity contact (contact when there is a large pit on the surface of the collector ring due to manufacturing quality defects and abnormal abrasion), and analyze the effects of the various states on the core parameters such as current conduction, ring surface damage, and carbon brush abrasion, which provide a basis for the active suppression of the damage.
- 20 December 2024
- Published by MDPI AG in Lubricants
- Vol. 12 (12) , 461
Open AccessExploring the Effect of Interface Contact States on Brush/Ring Current-Carrying Friction
A carbon brush/collector ring set will have phenomena such as firing and ablation during operation, which is due to the existence of various abnormal contact modes of the brush/ring during operation, thus changing the carbon brush/collector ring interface state. To analyze the effects of different contact modes on the performance of the brush/ring, in this paper, we construct the contact modes of the air gap (loss of contact leads to the existence of a small gap between the two surfaces), direct contact (contact with abrasive particulate media), and surface porosity contact (contact when there is a large pit on the surface of the collector ring due to manufacturing quality defects and abnormal abrasion), and analyze the effects of the various states on the core parameters such as current conduction, ring surface damage, and carbon brush abrasion, which provide a basis for the active suppression of the damage.
- Open Access
- 22 November 2024
- Published by MDPI AG in Preprints.org
Exploring the Effect of Interface Contact States on BrushRing Current-Carrying Friction
Carbon brush/collector ring of hydro generator set will have phenomena such as firing and ablation during operation, which is due to the existence of various abnormal contact modes of the brush/ring during operation, thus changing the carbon brush/collector ring interface state. In order to analyze the effects of different contact modes on the performance of the brush/ring. In this paper, we construct the contact modes of air gap (loss of contact leads to the existence of a small gap between the two surfaces), direct contact (contact with abrasive particulate media), and surface porosity contact (contact when there is a large pit on the surface of the collector ring due to manufacturing quality defects and abnormal abrasion), and we analyze the effects of the various states on the core parameters such as current conduction, ring surface damage, and carbon brush abrasion, which provide a basis for the active suppression of the damage.
- 22 November 2024
- Published by MDPI AG in Preprints.org
Open AccessExploring the Effect of Interface Contact States on BrushRing Current-Carrying Friction
Carbon brush/collector ring of hydro generator set will have phenomena such as firing and ablation during operation, which is due to the existence of various abnormal contact modes of the brush/ring during operation, thus changing the carbon brush/collector ring interface state. In order to analyze the effects of different contact modes on the performance of the brush/ring. In this paper, we construct the contact modes of air gap (loss of contact leads to the existence of a small gap between the two surfaces), direct contact (contact with abrasive particulate media), and surface porosity contact (contact when there is a large pit on the surface of the collector ring due to manufacturing quality defects and abnormal abrasion), and we analyze the effects of the various states on the core parameters such as current conduction, ring surface damage, and carbon brush abrasion, which provide a basis for the active suppression of the damage.
- Open Access
- 13 September 2023
- Published by MDPI AG in Lubricants
- Vol. 11 (9) , 398
Planar Reconstruction of Regular Surfaces’ Three-Dimensional Morphology and Tribology Application
The three-dimensional morphology of frictional sub-surfaces holds significant importance for studying tribological issues. However, the uniformity of the horizontal datum in 3D scanning is limited for curved surfaces, resulting in the inability to obtain accurate contour characterization parameters from the scanning results. This study aims to address this issue by constructing regular surface equations and normalizing the 3D profiler scanning results. By fitting the data, a “plane” surface representative of the surface features is obtained, and the paper demonstrates this approach on the surface morphology of different worn parts in the frictional area of spherical bearings located in the specific environment of the Three Gorges gate. The results indicate that the obtained “plane” effectively reconstructs the three-dimensional morphology map of the regular surface. Moreover, this reconstructed plane not only clearly illustrates the surface characteristics but also provides the foundation for analyzing the wear mechanism.
- 13 September 2023
- Published by MDPI AG in Lubricants
- Vol. 11 (9) , 398
Open AccessPlanar Reconstruction of Regular Surfaces’ Three-Dimensional Morphology and Tribology Application
The three-dimensional morphology of frictional sub-surfaces holds significant importance for studying tribological issues. However, the uniformity of the horizontal datum in 3D scanning is limited for curved surfaces, resulting in the inability to obtain accurate contour characterization parameters from the scanning results. This study aims to address this issue by constructing regular surface equations and normalizing the 3D profiler scanning results. By fitting the data, a “plane” surface representative of the surface features is obtained, and the paper demonstrates this approach on the surface morphology of different worn parts in the frictional area of spherical bearings located in the specific environment of the Three Gorges gate. The results indicate that the obtained “plane” effectively reconstructs the three-dimensional morphology map of the regular surface. Moreover, this reconstructed plane not only clearly illustrates the surface characteristics but also provides the foundation for analyzing the wear mechanism.
- Open Access
- 25 August 2023
- Published by MDPI AG in Preprints.org
Planar Reconstruction of Regular Surfaces’ Three-Dimensional Morphology and Tribology Application
The three-dimensional morphology of frictional sub-surfaces holds significant importance for studying tribological issues. However, the uniformity of horizontal datum in 3D scanning is limited for curved surfaces, resulting in the inability to obtain accurate contour characterization parameters from the scanning results. This study aims to address this issue by constructing regular surface equations and normalizing the 3D profiler scanning results. By fitting the data, a "plane" surface representative of the surface features is obtained, and the paper demonstrates this approach on the surface morphology of different worn parts in the frictional area of spherical bearings located in the specific environment of the Three Gorges gate. The results indicate that the obtained "plane" effectively reconstructs the three-dimensional morphology map of the regular surface. Moreover, this reconstructed plane not only clearly illustrates the surface characteristics but also provides the foundation for analyzing the wear mechanism.
- 25 August 2023
- Published by MDPI AG in Preprints.org
Open AccessPlanar Reconstruction of Regular Surfaces’ Three-Dimensional Morphology and Tribology Application
The three-dimensional morphology of frictional sub-surfaces holds significant importance for studying tribological issues. However, the uniformity of horizontal datum in 3D scanning is limited for curved surfaces, resulting in the inability to obtain accurate contour characterization parameters from the scanning results. This study aims to address this issue by constructing regular surface equations and normalizing the 3D profiler scanning results. By fitting the data, a "plane" surface representative of the surface features is obtained, and the paper demonstrates this approach on the surface morphology of different worn parts in the frictional area of spherical bearings located in the specific environment of the Three Gorges gate. The results indicate that the obtained "plane" effectively reconstructs the three-dimensional morphology map of the regular surface. Moreover, this reconstructed plane not only clearly illustrates the surface characteristics but also provides the foundation for analyzing the wear mechanism.
- 24 February 2021
- Published by Taylor & Francis in Materials and Manufacturing Processes
- Vol. 36 (8) , 979-986
Anti-icing capability of textured silicone rubber surfaces via laser processing
It is an undisputable fact that surface texture has a profound influence on the functional behavior of products. A method is proposed for manufacturing an anti-icing surface on silicone rubber composite material. Using a multi-function laser engraving machine, cylindrical micro-textures with different size and depth parameters are processed on the umbrella skirt surface of composite insulator samples. The optimal dimensional parameter of the surface micro-texture was determined by the best superhydrophobic property. By analyzing the freezing time of droplets, the influence of texture depth parameters on the anti-icing performance of the silicone rubber surface was investigated, which clearly confirmed that the contact angle affected anti-icing performance. Studying on adhesion of the ice on the sample surface and changing of the water contact angle after ice coating demonstrated the influence of texture-depth parameter on the deicing performance of silicone rubber surface. Thus, the characteristics and optimality of the texture specimen were obtained.
- 24 February 2021
- Published by Taylor & Francis in Materials and Manufacturing Processes
- Vol. 36 (8) , 979-986
Anti-icing capability of textured silicone rubber surfaces via laser processing
It is an undisputable fact that surface texture has a profound influence on the functional behavior of products. A method is proposed for manufacturing an anti-icing surface on silicone rubber composite material. Using a multi-function laser engraving machine, cylindrical micro-textures with different size and depth parameters are processed on the umbrella skirt surface of composite insulator samples. The optimal dimensional parameter of the surface micro-texture was determined by the best superhydrophobic property. By analyzing the freezing time of droplets, the influence of texture depth parameters on the anti-icing performance of the silicone rubber surface was investigated, which clearly confirmed that the contact angle affected anti-icing performance. Studying on adhesion of the ice on the sample surface and changing of the water contact angle after ice coating demonstrated the influence of texture-depth parameter on the deicing performance of silicone rubber surface. Thus, the characteristics and optimality of the texture specimen were obtained.
- Open Access
Performance Investigation on Different Designs of Superhydrophobic Surface Texture for Composite Insulator
To investigate the superhydrophobic properties of different surface textures, nine designs of textures with micro-nanostructures were produced successfully using the laser engraving technique on the surfaces of composite insulator umbrella skirt samples made of silicon rubber. The optimal parameters of the texture designs to give rise to the best hydrophobicity were determined. The surface morphology, abrasion resistance, corrosion resistance, self-cleaning and antifouling property of the different textured surfaces as well as water droplets rolling on the textured surfaces were studied experimentally using a contact angle meter, scanning electron microscope, three-dimensional topography meter and high-speed camera system. It was found that the diamond column design with optimal parameters has the best superhydrophobicity and overall performance. The most remarkable advantage of the optimal diamond column design is its robustness and long-term superhydrophobicity after repeated de-icing in harsh conditions. The reported work is an important step towards achieving superhydrophobic surface without coating for outdoor composite insulator in practical applications.
Open AccessPerformance Investigation on Different Designs of Superhydrophobic Surface Texture for Composite Insulator
To investigate the superhydrophobic properties of different surface textures, nine designs of textures with micro-nanostructures were produced successfully using the laser engraving technique on the surfaces of composite insulator umbrella skirt samples made of silicon rubber. The optimal parameters of the texture designs to give rise to the best hydrophobicity were determined. The surface morphology, abrasion resistance, corrosion resistance, self-cleaning and antifouling property of the different textured surfaces as well as water droplets rolling on the textured surfaces were studied experimentally using a contact angle meter, scanning electron microscope, three-dimensional topography meter and high-speed camera system. It was found that the diamond column design with optimal parameters has the best superhydrophobicity and overall performance. The most remarkable advantage of the optimal diamond column design is its robustness and long-term superhydrophobicity after repeated de-icing in harsh conditions. The reported work is an important step towards achieving superhydrophobic surface without coating for outdoor composite insulator in practical applications.