Hui-An Tsai
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Hui-An Tsai has a total of 69 co-authors. Here are the top co-authors by number of shared publications:
Kueir-Rarn Lee
Chung Yuan Christian University
9 shared publications- Micah Belle Marie Yap Ang
R&D Center for Membrane Technology, Department of Chemical Engineering, Chung Yuan Christian University, Taoyuan 32023, Taiwan
9 shared publications - Kueir-Rarn Lee
R&D Center for Membrane Technology, Department of Chemical Engineering, Chung Yuan Christian University, Taoyuan, Taiwan
8 shared publications - Shu-Hsien Huang
R&D Center for Membrane Technology, Department of Chemical Engineering, Chung Yuan Christian University, Taoyuan, Taiwan
8 shared publications Chi-Lan Li
Chung Yuan Christian University
7 shared publicationsJeremiah C. Millare
Mapúa University
5 shared publications
Latest Publications
- 29 September 2026
- Published by American Chemical Society (ACS) in ACS Applied Polymer Materials
- Vol. 8 (19) , 17722-17734
Functionalized UiO-66 Incorporated PVA Mixed-Matrix Membranes for Enhanced Methanol/Dimethyl Carbonate Pervaporation
Mixed-matrix membranes were prepared for methanol (MeOH)/dimethyl carbonate (DMC) pervaporation by incorporating UiO-66-(COOH)2, UiO-66-NH2, or polyethylenimine-functionalized UiO-66-NH2 (UiO-66-N-PEI) at the same nominal loading of 2.5 wt % into sulfosuccinic acid-crosslinked poly(vinyl alcohol) (PVA). The distinctive contribution of this study is a controlled, side-by-side comparison of carboxyl-, primary-amine-, and PEI-modified UiO-66 fillers within the same polymer matrix, crosslinking formulation, fabrication procedure, and operating conditions. Characterization showed that functionalization altered not only the filler surface chemistry but also particle size and accessible porosity. UiO-66-N-PEI exhibited the lowest BET surface area and pore volume and produced a thin, continuous selective layer. At 40 °C with a feed containing 10 wt % MeOH, its incorporation decreased membrane swelling from 18.25 ± 2.04% for pristine PVA to 6.69 ± 0.90%, while increasing the MeOH/DMC sorption selectivity from 421.04 to 945.18. The UiO-66-N-PEI/PVA membrane consequently exhibited the highest separation factor of 601 while maintaining a permeation flux of 642 g·m–2·h–1. Stable performance was maintained during 7 days of operation under these conditions. When the feed MeOH concentration increased to 70 wt %, the flux increased to 1689 g·m–2·h–1, whereas the separation factor decreased to 2.67, revealing a transition toward swelling-dominated transport near the azeotropic composition. These findings show that the observed performance results from the coupled effects of PEI-associated functionality, reduced pore accessibility, altered polymer packing, and swelling resistance rather than surface wettability alone. The optimized membrane is therefore more effective for removing residual MeOH from DMC-rich streams, while additional swelling control is required for efficient near-azeotropic separation.
- 29 September 2026
- Published by American Chemical Society (ACS) in ACS Applied Polymer Materials
- Vol. 8 (19) , 17722-17734
Functionalized UiO-66 Incorporated PVA Mixed-Matrix Membranes for Enhanced Methanol/Dimethyl Carbonate Pervaporation
Mixed-matrix membranes were prepared for methanol (MeOH)/dimethyl carbonate (DMC) pervaporation by incorporating UiO-66-(COOH)2, UiO-66-NH2, or polyethylenimine-functionalized UiO-66-NH2 (UiO-66-N-PEI) at the same nominal loading of 2.5 wt % into sulfosuccinic acid-crosslinked poly(vinyl alcohol) (PVA). The distinctive contribution of this study is a controlled, side-by-side comparison of carboxyl-, primary-amine-, and PEI-modified UiO-66 fillers within the same polymer matrix, crosslinking formulation, fabrication procedure, and operating conditions. Characterization showed that functionalization altered not only the filler surface chemistry but also particle size and accessible porosity. UiO-66-N-PEI exhibited the lowest BET surface area and pore volume and produced a thin, continuous selective layer. At 40 °C with a feed containing 10 wt % MeOH, its incorporation decreased membrane swelling from 18.25 ± 2.04% for pristine PVA to 6.69 ± 0.90%, while increasing the MeOH/DMC sorption selectivity from 421.04 to 945.18. The UiO-66-N-PEI/PVA membrane consequently exhibited the highest separation factor of 601 while maintaining a permeation flux of 642 g·m–2·h–1. Stable performance was maintained during 7 days of operation under these conditions. When the feed MeOH concentration increased to 70 wt %, the flux increased to 1689 g·m–2·h–1, whereas the separation factor decreased to 2.67, revealing a transition toward swelling-dominated transport near the azeotropic composition. These findings show that the observed performance results from the coupled effects of PEI-associated functionality, reduced pore accessibility, altered polymer packing, and swelling resistance rather than surface wettability alone. The optimized membrane is therefore more effective for removing residual MeOH from DMC-rich streams, while additional swelling control is required for efficient near-azeotropic separation.
- Open Access
Using Tannic-Acid-Based Complex to Modify Polyacrylonitrile Hollow Fiber Membrane for Efficient Oil-In-Water Separation
Separating oil from water allows us to reuse both fluids for various applications, leading to a more economical process. Membrane separation has been evidenced as a cost-effective process for wastewater treatment. A hollow fiber membrane made of polyacrylonitrile (PAN) is an excellent choice for separating oil from water because of its superior chemical resistance. Its low antifouling ability, however, reduces the effectiveness of its separation. Hence, in this study, we used tannic acid (TA) and FeIII complex to modify the surface of the PAN hollow fiber membrane. To improve membrane performance, different reaction times were investigated. The results demonstrate that even when the TA-FeIII covered the pores of the PAN membrane, the water flux remained constant. However, when an emulsion was fed to the feed solution, the flux increased from 50 to 66 LMH, indicating low oil adhesion on the surface of the modified membrane. When compared to the pristine membrane, the modified membrane had superior antifouling and reusability. As a result, the hydrophilic TA-FeIII complex on PAN surface improves overall membrane performance.
Open AccessUsing Tannic-Acid-Based Complex to Modify Polyacrylonitrile Hollow Fiber Membrane for Efficient Oil-In-Water Separation
Separating oil from water allows us to reuse both fluids for various applications, leading to a more economical process. Membrane separation has been evidenced as a cost-effective process for wastewater treatment. A hollow fiber membrane made of polyacrylonitrile (PAN) is an excellent choice for separating oil from water because of its superior chemical resistance. Its low antifouling ability, however, reduces the effectiveness of its separation. Hence, in this study, we used tannic acid (TA) and FeIII complex to modify the surface of the PAN hollow fiber membrane. To improve membrane performance, different reaction times were investigated. The results demonstrate that even when the TA-FeIII covered the pores of the PAN membrane, the water flux remained constant. However, when an emulsion was fed to the feed solution, the flux increased from 50 to 66 LMH, indicating low oil adhesion on the surface of the modified membrane. When compared to the pristine membrane, the modified membrane had superior antifouling and reusability. As a result, the hydrophilic TA-FeIII complex on PAN surface improves overall membrane performance.
- Open Access
Enhancing Performance of Thin-Film Nanocomposite Membranes by Embedding in Situ Silica Nanoparticles
In this work, silica nanoparticles were produced in situ, to be embedded eventually in the polyamide layer formed during interfacial polymerization for fabricating thin-film nanocomposite membranes with enhanced performance for dehydrating isopropanol solution. The nanoparticles were synthesized through a sol-gel reaction between 3-aminopropyltrimethoxysilane (APTMOS) and 1,3-cyclohexanediamine (CHDA). Two monomers—CHDA (with APTMOS) and trimesoyl chloride—were reacted on a hydrolyzed polyacrylonitrile (hPAN) support. To obtain optimum fabricating conditions, the ratio of APTMOS to CHDA and reaction time were varied. Field emission scanning electron microscopy (FESEM) and atomic force microscopy (AFM) were used to illustrate the change in morphology as a result of embedding silica nanoparticles. The optimal conditions for preparing the nanocomposite membrane turned out to be 0.15 (g/g) APTMOS/CHDA and 60 min mixing of APTMOS and CHDA, leading to the following membrane performance: flux = 1071 ± 79 g∙m−2∙h−1, water concentration in permeate = 97.34 ± 0.61%, and separation factor = 85.39. A stable performance was shown by the membrane under different operating conditions, where the water concentration in permeate was more than 90 wt%. Therefore, the embedment of silica nanoparticles generated in situ enhanced the separation efficiency of the membrane.
Open AccessEnhancing Performance of Thin-Film Nanocomposite Membranes by Embedding in Situ Silica Nanoparticles
In this work, silica nanoparticles were produced in situ, to be embedded eventually in the polyamide layer formed during interfacial polymerization for fabricating thin-film nanocomposite membranes with enhanced performance for dehydrating isopropanol solution. The nanoparticles were synthesized through a sol-gel reaction between 3-aminopropyltrimethoxysilane (APTMOS) and 1,3-cyclohexanediamine (CHDA). Two monomers—CHDA (with APTMOS) and trimesoyl chloride—were reacted on a hydrolyzed polyacrylonitrile (hPAN) support. To obtain optimum fabricating conditions, the ratio of APTMOS to CHDA and reaction time were varied. Field emission scanning electron microscopy (FESEM) and atomic force microscopy (AFM) were used to illustrate the change in morphology as a result of embedding silica nanoparticles. The optimal conditions for preparing the nanocomposite membrane turned out to be 0.15 (g/g) APTMOS/CHDA and 60 min mixing of APTMOS and CHDA, leading to the following membrane performance: flux = 1071 ± 79 g∙m−2∙h−1, water concentration in permeate = 97.34 ± 0.61%, and separation factor = 85.39. A stable performance was shown by the membrane under different operating conditions, where the water concentration in permeate was more than 90 wt%. Therefore, the embedment of silica nanoparticles generated in situ enhanced the separation efficiency of the membrane.