Frantisek Miksik
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Frantisek Miksik has a total of 48 co-authors. Here are the top co-authors by number of shared publications:
- Kyaw Thu
Department of Advanced Environmental Science and Engineering, Faculty of Engineering Sciences, Kyushu University, Kasuga-koen 6-1, Kasuga, Fukuoka 816-8580, Japan
16 shared publications Takahiko Miyazaki
13 shared publications- Takahiko Miyazaki
Department of Advanced Environmental Science and Engineering, Kyushu University, Fukuoka 816-8580, Japan
11 shared publications Agung Tri Wijayanta
5 shared publicationsJin Miyawaki
5 shared publicationsKoji Nakabayashi
5 shared publications
Latest Publications
- Open Access
- 13 June 2026
- Published by Elsevier in Chemical Engineering Journal
- Vol. 543
Experimental evaluation of 3D printed metal monolithic adsorption bed with fast heat transfer rate for CO2 separation
- 13 June 2026
- Published by Elsevier in Chemical Engineering Journal
- Vol. 543
Open AccessExperimental evaluation of 3D printed metal monolithic adsorption bed with fast heat transfer rate for CO2 separation
- 6 November 2024
- Published by Elsevier in Advanced Powder Technology
- Vol. 35 (12)
Optimization of conventional-zeolite-synthesis from waste pumice for water adsorption
- 6 November 2024
- Published by Elsevier in Advanced Powder Technology
- Vol. 35 (12)
Optimization of conventional-zeolite-synthesis from waste pumice for water adsorption
- 26 October 2024
- Published by Springer Nature in Journal of Materials Science
- Vol. 59 (43) , 20121-20156
A review of recent advances in sustainable preparation of high-performing activated carbon for dehumidification technology
- 26 October 2024
- Published by Springer Nature in Journal of Materials Science
- Vol. 59 (43) , 20121-20156
A review of recent advances in sustainable preparation of high-performing activated carbon for dehumidification technology
- 1 January 2024
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 3163 (1) , 040002
Adsorption thermal energy storage: The problematic of theoretical and practical adsorption materials performance
Adsorption thermal energy storage (aTES) is one of the possible technologies that could help to eliminate our dependence on fossil fuels. The advantages of the Adsorption thermal energy storage (aTES) is one of the possible technologies that could help to eliminate our dependence on fossil fuels. The advantages of the
- 1 January 2024
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 3163 (1) , 040002
Adsorption thermal energy storage: The problematic of theoretical and practical adsorption materials performance
Adsorption thermal energy storage (aTES) is one of the possible technologies that could help to eliminate our dependence on fossil fuels. The advantages of the Adsorption thermal energy storage (aTES) is one of the possible technologies that could help to eliminate our dependence on fossil fuels. The advantages of the
- Open Access
- 1 January 2023
- Published by Elsevier in SSRN Electronic Journal
Fabrication of the Novel Mixed Matrix Polymer Electrolyte Membranes (PEMs) Intended for Hydrogen Production Via Electrolysis Application
Hydrogen gas is among the sustainable energy forms that counteract the energy crisis since it guarantees zero greenhouse gases’ emissions. This study presents the use of biomass fillers and polyvinyl alcohol (PVA) plus polyvinyl pyrrolidone (PVP) polymers to fabricate cost-effective polymer electrolyte membranes (PEMs) whose application was H2 generation through electrolysis. A positive Faradaic efficiency ranging between 82.8±1.9% to 88.9±1.6% was exhibited when voltage of 6.5V, 8V and 10V is applied and proton conduction hence H2 generation commenced from 2-2.5V voltage range. The apparent morphology of the PEMs that verified the incorporation of Pine bark (PB) and Chinese Tallow Capsule (CT) fillers was visible as surface bumps and internal cavities within the PEMs. Nafion 115 membrane showed the best H2 production and proton conductivity of 23.94 mS/cm whereas that of the PB, CT and SSA were 1.33, 0.46 and 0.48 mS/cm respectively. The membrane characteristics were improved in the presence of fillers, specifically PB thus it had a good water adsorption therefore H2 generation. The improved functional groups of PB membrane improved its H2 production but the losses like bubbles’ production affected the efficiency. This research represents a cost-effective H2 production alternative that can be utilized in diverse applications.
- 1 January 2023
- Published by Elsevier in SSRN Electronic Journal
Open AccessFabrication of the Novel Mixed Matrix Polymer Electrolyte Membranes (PEMs) Intended for Hydrogen Production Via Electrolysis Application
Hydrogen gas is among the sustainable energy forms that counteract the energy crisis since it guarantees zero greenhouse gases’ emissions. This study presents the use of biomass fillers and polyvinyl alcohol (PVA) plus polyvinyl pyrrolidone (PVP) polymers to fabricate cost-effective polymer electrolyte membranes (PEMs) whose application was H2 generation through electrolysis. A positive Faradaic efficiency ranging between 82.8±1.9% to 88.9±1.6% was exhibited when voltage of 6.5V, 8V and 10V is applied and proton conduction hence H2 generation commenced from 2-2.5V voltage range. The apparent morphology of the PEMs that verified the incorporation of Pine bark (PB) and Chinese Tallow Capsule (CT) fillers was visible as surface bumps and internal cavities within the PEMs. Nafion 115 membrane showed the best H2 production and proton conductivity of 23.94 mS/cm whereas that of the PB, CT and SSA were 1.33, 0.46 and 0.48 mS/cm respectively. The membrane characteristics were improved in the presence of fillers, specifically PB thus it had a good water adsorption therefore H2 generation. The improved functional groups of PB membrane improved its H2 production but the losses like bubbles’ production affected the efficiency. This research represents a cost-effective H2 production alternative that can be utilized in diverse applications.