Sharvil Patil
Sharvil Patil has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Hajime Shibata
Analog Devices Canada, Toronto, ON, Canada
3 shared publications Prawal Shrestha
Analog Devices Inc., San Diego, CA, USA
2 shared publications- Yannis Tsividis
Columbia University, New York, NY, United States
2 shared publications - Zhao Li
Analog Devices Canada, Toronto, ON, Canada
2 shared publications Alin Ratiu
CEA-LETI-MINATEC, Grenoble, France
1 shared publication- Anantha P. Chandrakasan
Department of Electrical Engineering and Computer Science, Massachusetts Institute of Technology, Cambridge, USA
1 shared publication
Latest Publications
- 14 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 59 (12) , 4225-4236
A −90-dBFS-IM3, −164-dBFS/Hz-NSD, 700-MHz-Bandwidth Continuous-Time Pipelined ADC With Digital Cancellation of DAC Errors
This paper describes a continuous-time (CT) pipelined analog-to-digital converter (ADC) that represents a technology push along both —third-order distortion and noise—dimensions. Distortion is tackled using on-chip digital cancellation of static and timing digital-to-analog converter (DAC) mismatch errors. Low noise is achieved with design choices such as a resistive sub-DAC; a high-precision, on-chip, background-calibrated digital reconstruction filter (DRF); and a tunable LC lattice delay that allows a programmable sampling frequency. Implemented in a 16-nm FinFET process, the 6.4-GS/s prototype achieves an IM $_{3}$ of $-$ 90 dBFS and a small-signal NSD of $-$ 164 dBFS/Hz over a 700-MHz bandwidth, while dissipating 703-mW power. Such performance makes it suitable for high-performance instrumentation and communications that demand robustness to large interferers while digitizing small signals.
- 14 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 59 (12) , 4225-4236
A −90-dBFS-IM3, −164-dBFS/Hz-NSD, 700-MHz-Bandwidth Continuous-Time Pipelined ADC With Digital Cancellation of DAC Errors
This paper describes a continuous-time (CT) pipelined analog-to-digital converter (ADC) that represents a technology push along both —third-order distortion and noise—dimensions. Distortion is tackled using on-chip digital cancellation of static and timing digital-to-analog converter (DAC) mismatch errors. Low noise is achieved with design choices such as a resistive sub-DAC; a high-precision, on-chip, background-calibrated digital reconstruction filter (DRF); and a tunable LC lattice delay that allows a programmable sampling frequency. Implemented in a 16-nm FinFET process, the 6.4-GS/s prototype achieves an IM $_{3}$ of $-$ 90 dBFS and a small-signal NSD of $-$ 164 dBFS/Hz over a 700-MHz bandwidth, while dissipating 703-mW power. Such performance makes it suitable for high-performance instrumentation and communications that demand robustness to large interferers while digitizing small signals.
- 11 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 59 (4) , 1158-1170
A 6.4-GS/s 1-GHz BW Continuous-Time Pipelined ADC With Time-Interleaved Sub-ADC-DAC Achieving 61.7-dB SNDR in 16-nm FinFET
We introduce a continuous-time (CT) pipeline analog-to-digital converter (ADC) featuring a time-interleaved sub-ADC-digital-to-analog converter (DAC) path in its first stage. The proposed sub-ADC-DAC path enhances the ADC’s bandwidth by improving the signal cancellation at the summing node of the first stage. In addition, we have developed an inductorless delay line for the first stage, improving the amplitude and phase matching, thus minimizing the input signal leakage into the backend ADC. Furthermore, the theoretical jitter limitations in the CT pipeline architecture have been explored, and the proposed theory is compared against the measured results. The prototype ADC was fabricated in a 16-nm FinFET process. The ADC achieves a peak signal-to-noise ratio (SNR) of 61.7 dB at low frequencies and 60.8 dB at high frequencies across a 1-GHz bandwidth. The active area of the ADC is 0.77 mm $^2$ , and it consumes 240 mW. The Schreier figure of merit (FOM $_S$ ) is 157.9 dB, which is amongst the best for CT ADCs with bandwidth greater than 500 MHz.
- 11 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 59 (4) , 1158-1170
A 6.4-GS/s 1-GHz BW Continuous-Time Pipelined ADC With Time-Interleaved Sub-ADC-DAC Achieving 61.7-dB SNDR in 16-nm FinFET
We introduce a continuous-time (CT) pipeline analog-to-digital converter (ADC) featuring a time-interleaved sub-ADC-digital-to-analog converter (DAC) path in its first stage. The proposed sub-ADC-DAC path enhances the ADC’s bandwidth by improving the signal cancellation at the summing node of the first stage. In addition, we have developed an inductorless delay line for the first stage, improving the amplitude and phase matching, thus minimizing the input signal leakage into the backend ADC. Furthermore, the theoretical jitter limitations in the CT pipeline architecture have been explored, and the proposed theory is compared against the measured results. The prototype ADC was fabricated in a 16-nm FinFET process. The ADC achieves a peak signal-to-noise ratio (SNR) of 61.7 dB at low frequencies and 60.8 dB at high frequencies across a 1-GHz bandwidth. The active area of the ADC is 0.77 mm $^2$ , and it consumes 240 mW. The Schreier figure of merit (FOM $_S$ ) is 157.9 dB, which is amongst the best for CT ADCs with bandwidth greater than 500 MHz.
- 2 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 69 (12) , 4731-4740
A Design Methodology for Achieving Near Nyquist Continuous Time Pipelined ADCs
Continuous-time pipelined (CTP) ADCs have shown the potential to alleviate the challenges of discrete-time (DT) pipelined converters with Multi-GHz bandwidth, but have so far required an oversampling ratio (OSR) of at least 4. After elucidating the factors that limit CTP bandwidth, this paper presents a design methodology for near-Nyquist CTP ADCs. The delay circuit is optimized to match the ADC/DAC path in both its broadband magnitude response and phase. The residue filter response is optimized to prevent image signals from overloading the subsequent stage. We show that practical circuits can realize these optimized responses and extend the bandwidth of the CTP architecture to OSRs of 1.5-2.0, essentially equivalent to the OSR of DT converters when allowing for practical anti-aliasing. The direct path (i.e. delay) and the residue-amplifying filter circuits required for 3 GHz bandwidth are incorporated into a complete 4-bit 10 GS/s CTP ADC stage in a 28nm CMOS prototype. Simulation and measurement results confirm that CTP ADCs can operate at a near-Nyquist sampling rate with an OSR of 1.7.
- 2 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 69 (12) , 4731-4740
A Design Methodology for Achieving Near Nyquist Continuous Time Pipelined ADCs
Continuous-time pipelined (CTP) ADCs have shown the potential to alleviate the challenges of discrete-time (DT) pipelined converters with Multi-GHz bandwidth, but have so far required an oversampling ratio (OSR) of at least 4. After elucidating the factors that limit CTP bandwidth, this paper presents a design methodology for near-Nyquist CTP ADCs. The delay circuit is optimized to match the ADC/DAC path in both its broadband magnitude response and phase. The residue filter response is optimized to prevent image signals from overloading the subsequent stage. We show that practical circuits can realize these optimized responses and extend the bandwidth of the CTP architecture to OSRs of 1.5-2.0, essentially equivalent to the OSR of DT converters when allowing for practical anti-aliasing. The direct path (i.e. delay) and the residue-amplifying filter circuits required for 3 GHz bandwidth are incorporated into a complete 4-bit 10 GS/s CTP ADC stage in a 28nm CMOS prototype. Simulation and measurement results confirm that CTP ADCs can operate at a near-Nyquist sampling rate with an OSR of 1.7.
- 13 November 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 66 (3) , 1017-1030
Signal Encoding and Processing in Continuous Time Using a Cascade of Digital Delays
We consider a digital encoding/processing system in which both the analog-to-digital converter and the digital signal processor are implemented by repeating a single fundamental design unit: the digital delay. Timing becomes an integral part of the resulting signal representation and processing, thereby promising to improve with technology scaling. System properties are studied and design considerations for a potential integrated implementation are discussed. Simulation results confirm the theory.
- 13 November 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 66 (3) , 1017-1030
Signal Encoding and Processing in Continuous Time Using a Cascade of Digital Delays
We consider a digital encoding/processing system in which both the analog-to-digital converter and the digital signal processor are implemented by repeating a single fundamental design unit: the digital delay. Timing becomes an integral part of the resulting signal representation and processing, thereby promising to improve with technology scaling. System properties are studied and design considerations for a potential integrated implementation are discussed. Simulation results confirm the theory.
- 1 June 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. C160-C161
A 310fJ/conv-step 0.0032mm2 error-shaping alias-free asynchronous ADC
We present a programmable, quantization error spectral shaping, alias-free asynchronous ADC suited for clockless, continuous-time DSP in receivers with modest SNDR requirements and a tight power budget. Implemented in 0.65V 28nm FDSOI, the 0.0032mm 2 ADC achieves 32dB-42dB SNDR over a 10MHz-50MHz BW while consuming 24μW, giving a 3-10fJ/conv-step FoM.
- 1 June 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. C160-C161
A 310fJ/conv-step 0.0032mm2 error-shaping alias-free asynchronous ADC
We present a programmable, quantization error spectral shaping, alias-free asynchronous ADC suited for clockless, continuous-time DSP in receivers with modest SNDR requirements and a tight power budget. Implemented in 0.65V 28nm FDSOI, the 0.0032mm 2 ADC achieves 32dB-42dB SNDR over a 10MHz-50MHz BW while consuming 24μW, giving a 3-10fJ/conv-step FoM.