Fabio A. Bendana
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Fabio A. Bendana has a total of 51 co-authors. Here are the top co-authors by number of shared publications:
Daniel D. Lee
7 shared publicationsR. Mitchell Spearrin
University of California, Los Angeles (UCLA), Los Angeles, California 90095
7 shared publications- R. Mitchell Spearrin
University of California, Los Angeles, Los Angeles, California 90095
6 shared publications Raymond M. Spearrin
University of California, Los Angeles
4 shared publicationsAnil P. Nair
3 shared publicationsDaniel I. Pineda
3 shared publications
Latest Publications
- Open Access
- 6 February 2026
- Published by Elsevier in SSRN Electronic Journal
Microalloying effects on oxide tribolayer stability and frictional ignition
Frictional heating at sliding contacts in high-pressure oxygen can trigger metal fires, a potentially catastrophic failure mode in oxygen-rich systems. We previously showed that frictional ignition occurs when two conditions are met: (i) the thermal ignition criterion is satisfied at the sliding interface, such that the oxidative heat flux exceeds dissipative heat losses, and (ii) hot metal contacts are exposed to the oxidizing environment, for example through breakdown of a protective oxide tribolayer. Building on these insights, the present work examines the role of alloy composition in controlling tribolayer stability and frictional ignition in three model alloys – stainless steels 304 and 316, and Inconel IN718 – during high-speed sliding in high-pressure oxygen. Under slowly ramped loads, all three alloys form lubricating oxide tribolayers, consistent with prior observations. In contrast, under rapid loading conditions, tribolayers do not have sufficient time to develop before ignition occurs. Stainless steel 304 ignites at higher interfacial temperatures (~1570 K), associated with substrate melting, whereas stainless steel 316 and Inconel 718 ignite at significantly lower temperatures (~1000 K) due to the formation and melting of MoO3 within the tribolayer. These results demonstrate that even minor microalloying additions, such as Mo in stainless steel 316 and Inconel 718, can substantially reduce ignition resistance by compromising the thermochemical stability of oxide tribolayers at low temperatures.
- 6 February 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessMicroalloying effects on oxide tribolayer stability and frictional ignition
Frictional heating at sliding contacts in high-pressure oxygen can trigger metal fires, a potentially catastrophic failure mode in oxygen-rich systems. We previously showed that frictional ignition occurs when two conditions are met: (i) the thermal ignition criterion is satisfied at the sliding interface, such that the oxidative heat flux exceeds dissipative heat losses, and (ii) hot metal contacts are exposed to the oxidizing environment, for example through breakdown of a protective oxide tribolayer. Building on these insights, the present work examines the role of alloy composition in controlling tribolayer stability and frictional ignition in three model alloys – stainless steels 304 and 316, and Inconel IN718 – during high-speed sliding in high-pressure oxygen. Under slowly ramped loads, all three alloys form lubricating oxide tribolayers, consistent with prior observations. In contrast, under rapid loading conditions, tribolayers do not have sufficient time to develop before ignition occurs. Stainless steel 304 ignites at higher interfacial temperatures (~1570 K), associated with substrate melting, whereas stainless steel 316 and Inconel 718 ignite at significantly lower temperatures (~1000 K) due to the formation and melting of MoO3 within the tribolayer. These results demonstrate that even minor microalloying additions, such as Mo in stainless steel 316 and Inconel 718, can substantially reduce ignition resistance by compromising the thermochemical stability of oxide tribolayers at low temperatures.
- Open Access
- 25 December 2024
- Published by Elsevier in Tribology International
- Vol. 205
Oxide tribolayer breakdown on sliding metal contacts drives thermal ignition
- 25 December 2024
- Published by Elsevier in Tribology International
- Vol. 205
Open AccessOxide tribolayer breakdown on sliding metal contacts drives thermal ignition
- 22 October 2024
- Published by Elsevier in Aerospace Science and Technology
- Vol. 155
Additively-manufactured shear tri-coaxial rocket injector mixing and combustion characteristics
- 22 October 2024
- Published by Elsevier in Aerospace Science and Technology
- Vol. 155
Additively-manufactured shear tri-coaxial rocket injector mixing and combustion characteristics
- 1 April 2022
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Thermophysics and Heat Transfer
- Vol. 36 (2) , 266-275
Nonequilibrium Vibrational, Rotational, and Translational Thermometry via Megahertz Laser Absorption of CO
A mid-infrared laser absorption strategy for simultaneously measuring translational, rotational, and vibrational temperatures of carbon monoxide (CO) at high speeds was developed for application to...
- 1 April 2022
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Thermophysics and Heat Transfer
- Vol. 36 (2) , 266-275
Nonequilibrium Vibrational, Rotational, and Translational Thermometry via Megahertz Laser Absorption of CO
A mid-infrared laser absorption strategy for simultaneously measuring translational, rotational, and vibrational temperatures of carbon monoxide (CO) at high speeds was developed for application to...
- 1 November 2021
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Propulsion and Power
- Vol. 37 (6) , 928-943
Injector Effects on Hybrid Polymethylmethacrylate Combustion Assessed by Thermochemical Tomography
In this work, two representative hybrid rocket injector designs, a single-port and an axial showerhead design, were examined experimentally to determine the comparative influence on the development...
- 1 November 2021
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Propulsion and Power
- Vol. 37 (6) , 928-943
Injector Effects on Hybrid Polymethylmethacrylate Combustion Assessed by Thermochemical Tomography
In this work, two representative hybrid rocket injector designs, a single-port and an axial showerhead design, were examined experimentally to determine the comparative influence on the development...
- 31 August 2021
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 32 (12) , 125203
Localized characteristic velocity (c*) for rocket combustion analysis based on gas temperature and composition via laser absorption spectroscopy
In this work, a method for experimentally determining a local characteristic velocity, c ∗ , is presented for purposes of analyzing rocket combustion progress based on in-situ laser absorption spectroscopy measurements of temperature and gas composition. Measuring c ∗ from spatially-varying thermochemical properties provides an alternative to the classical c ∗ evaluation, which uses global chamber pressure and mass flow rate measurements. Accordingly, the novel method provides more detailed insight to the underlying mechanisms (multi-phase thermochemistry, diffusive mixing, turbulence, etc) governing combustion performance in the spatial domain. The method is demonstrated on an RP-2/O 2 liquid-propellant rocket engine (LRE) and a PMMA/O 2 hybrid rocket combustion experiment. Localized c ∗ results for the LRE are obtained via in-chamber measurements of temperature, CO, and CO 2 and are presented over a range of pressures ( P = 28–83 bar) and mixture ratios (MR = 2.5–5). For the hybrid rocket combustion experiment, one-dimensional tomographic reconstruction techniques are used to spatially-resolve the flow-field thermochemistry and obtain spatially-resolved measurements of temperature, CO, CO 2 , and H 2 O. These measurements are compiled to obtain spatially-resolved c ∗ images of the combustion zone. The c ∗ results from both experiments are compared to the theoretical c ∗ expected from chemical equilibrium, providing for a method to assess combustion performance or progress locally within the combustion zone.
- 31 August 2021
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 32 (12) , 125203
Localized characteristic velocity (c*) for rocket combustion analysis based on gas temperature and composition via laser absorption spectroscopy
In this work, a method for experimentally determining a local characteristic velocity, c ∗ , is presented for purposes of analyzing rocket combustion progress based on in-situ laser absorption spectroscopy measurements of temperature and gas composition. Measuring c ∗ from spatially-varying thermochemical properties provides an alternative to the classical c ∗ evaluation, which uses global chamber pressure and mass flow rate measurements. Accordingly, the novel method provides more detailed insight to the underlying mechanisms (multi-phase thermochemistry, diffusive mixing, turbulence, etc) governing combustion performance in the spatial domain. The method is demonstrated on an RP-2/O 2 liquid-propellant rocket engine (LRE) and a PMMA/O 2 hybrid rocket combustion experiment. Localized c ∗ results for the LRE are obtained via in-chamber measurements of temperature, CO, and CO 2 and are presented over a range of pressures ( P = 28–83 bar) and mixture ratios (MR = 2.5–5). For the hybrid rocket combustion experiment, one-dimensional tomographic reconstruction techniques are used to spatially-resolve the flow-field thermochemistry and obtain spatially-resolved measurements of temperature, CO, CO 2 , and H 2 O. These measurements are compiled to obtain spatially-resolved c ∗ images of the combustion zone. The c ∗ results from both experiments are compared to the theoretical c ∗ expected from chemical equilibrium, providing for a method to assess combustion performance or progress locally within the combustion zone.
- 1 January 2021
- Published by Elsevier in Proceedings of the Combustion Institute
- Vol. 38 (1) , 1685-1693
Exploiting line-mixing effects for laser absorption spectroscopy at extreme combustion pressures
- 1 January 2021
- Published by Elsevier in Proceedings of the Combustion Institute
- Vol. 38 (1) , 1685-1693
Exploiting line-mixing effects for laser absorption spectroscopy at extreme combustion pressures
- 9 August 2020
- Published by Springer Nature in Experiments in Fluids
- Vol. 61 (9) , 1-13
In-situ thermochemical analysis of hybrid rocket fuel oxidation via laser absorption tomography of $\text {CO}$, $\text {CO}_{2}$, and $\text {H}_{2}\text {O}$- 9 August 2020
- Published by Springer Nature in Experiments in Fluids
- Vol. 61 (9) , 1-13
In-situ thermochemical analysis of hybrid rocket fuel oxidation via laser absorption tomography of $\text {CO}$, $\text {CO}_{2}$, and $\text {H}_{2}\text {O}$