Jovan Tatar
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Jovan Tatar has a total of 62 co-authors. Here are the top co-authors by number of shared publications:
Sandra Milev
Univ. of Delaware
6 shared publicationsSiamak Sattar
NIST, Engn Lab, Gaithersburg, MD 20899 USA
3 shared publicationsArkabrata Sinha
Department of Civil and Environmental Engineering University of Massachusetts Lowell Lowell Massachusetts USA
2 shared publications- David G. Goodwin
California Institute of Technology
2 shared publications - Harry W. Shenton
Department of Civil and Environmental Engineering, University of Delaware, Newark, DE, USA
2 shared publications Kent A. Harries
Univ. of Pittsburgh
2 shared publications
Latest Publications
- 1 November 2026
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 38 (11)
Self-Healing Polysulfide–Epoxy Sealants for Concrete Pavement Joints
The development of self-healing polymers has primarily focused on enabling healing functionality, while comparatively little attention has been paid to meeting specific performance criteria. Without performance benchmarks, it is difficult to guide material design toward practical use. This study investigates a self-healing sealant for concrete pavement joints that incorporates dynamic disulfide bonds. The sealant—prepared from commercially available thiol-terminated polysulfides (LP55) and bisphenol-A epoxy resin—was evaluated under environmental and load conditions typical for concrete pavements. Static displacement was applied to assess self-healing and bond durability under freeze–thaw cycling. Two tertiary amines, 2,4,6-tris(dimethylaminomethyl)phenol (DMP) and triethylamine (TEA), were tested as initiators to study their effect on polymer curing. Fourier transform infrared analysis confirmed complete curing under ambient conditions within 3 weeks. The cured polymer exhibited a low glass transition temperature ( − 35 ° C ), favorable for flexibility in cold climates. Tensile tests showed higher strength for the TEA-cured sample (465 kPa) compared to the one cured with DMP (190 kPa). The thiol–epoxy sealant demonstrated stronger adhesion to concrete than a commercial silicone. Self-healing efficiency improved in some formulations when joint displacement increased from 1 mm to 2 mm. Overall, the results demonstrate that thiol–epoxy sealants with dynamic bonding can meet key performance requirements for pavement applications. They also highlight the need for further investigation into the effects of initiator chemistry on polymer performance and strategies to reduce residual deformation under low-rate loading.
- 1 November 2026
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 38 (11)
Self-Healing Polysulfide–Epoxy Sealants for Concrete Pavement Joints
The development of self-healing polymers has primarily focused on enabling healing functionality, while comparatively little attention has been paid to meeting specific performance criteria. Without performance benchmarks, it is difficult to guide material design toward practical use. This study investigates a self-healing sealant for concrete pavement joints that incorporates dynamic disulfide bonds. The sealant—prepared from commercially available thiol-terminated polysulfides (LP55) and bisphenol-A epoxy resin—was evaluated under environmental and load conditions typical for concrete pavements. Static displacement was applied to assess self-healing and bond durability under freeze–thaw cycling. Two tertiary amines, 2,4,6-tris(dimethylaminomethyl)phenol (DMP) and triethylamine (TEA), were tested as initiators to study their effect on polymer curing. Fourier transform infrared analysis confirmed complete curing under ambient conditions within 3 weeks. The cured polymer exhibited a low glass transition temperature ( − 35 ° C ), favorable for flexibility in cold climates. Tensile tests showed higher strength for the TEA-cured sample (465 kPa) compared to the one cured with DMP (190 kPa). The thiol–epoxy sealant demonstrated stronger adhesion to concrete than a commercial silicone. Self-healing efficiency improved in some formulations when joint displacement increased from 1 mm to 2 mm. Overall, the results demonstrate that thiol–epoxy sealants with dynamic bonding can meet key performance requirements for pavement applications. They also highlight the need for further investigation into the effects of initiator chemistry on polymer performance and strategies to reduce residual deformation under low-rate loading.
- 1 October 2026
- Published by American Society of Civil Engineers (ASCE) in Journal of Composites for Construction
- Vol. 30 (5) , 05026003
Twenty-Two Years Later: Assessing the Durability Performance of Externally Bonded CFRP Laminates on a Highway Steel Bridge Girder
This study evaluates the long-term durability of carbon fiber–reinforced polymer (CFRP) composites used to strengthen a steel bridge girder on Interstate 95 in Newark, Delaware, 22 years after installation. The original retrofit program combined laboratory and field investigations to validate the structural contribution and fatigue durability of CFRP bonded to the tension flange of steel girders. Approximately two decades later, a follow-up assessment was conducted to examine the condition of the bonded CFRP system under actual service conditions. Field-extracted CFRP samples were tested in tension and compared to control specimens stored under laboratory conditions for 22 years. Compared with control specimens stored under laboratory conditions, field-exposed samples showed 15% lower tensile strength and 26% lower flexural modulus. Corrosion was observed beneath the CFRP at the northern end of the girder, likely due to galvanic coupling between the steel substrate and the carbon fibers in the presence of moisture. Structural health monitoring was performed on the retrofitted girder, and newly collected strain data were compared to original measurements. Differential scanning calorimetry revealed that the glass transition temperature of both field-cured adhesives was below the 66°C minimum recommended by AASHTO guidelines. Fourier transform infrared spectroscopy indicated minor chemical changes in the field-exposed CFRP. The CFRP system has maintained its bond integrity over two decades; however, in regions where corrosion developed beneath the CFRP, the bond integrity was compromised. This study provides rare, long-term performance data on CFRP–steel retrofits in field conditions and supports their continued use to extend the life of aging steel infrastructure.
- 1 October 2026
- Published by American Society of Civil Engineers (ASCE) in Journal of Composites for Construction
- Vol. 30 (5) , 05026003
Twenty-Two Years Later: Assessing the Durability Performance of Externally Bonded CFRP Laminates on a Highway Steel Bridge Girder
This study evaluates the long-term durability of carbon fiber–reinforced polymer (CFRP) composites used to strengthen a steel bridge girder on Interstate 95 in Newark, Delaware, 22 years after installation. The original retrofit program combined laboratory and field investigations to validate the structural contribution and fatigue durability of CFRP bonded to the tension flange of steel girders. Approximately two decades later, a follow-up assessment was conducted to examine the condition of the bonded CFRP system under actual service conditions. Field-extracted CFRP samples were tested in tension and compared to control specimens stored under laboratory conditions for 22 years. Compared with control specimens stored under laboratory conditions, field-exposed samples showed 15% lower tensile strength and 26% lower flexural modulus. Corrosion was observed beneath the CFRP at the northern end of the girder, likely due to galvanic coupling between the steel substrate and the carbon fibers in the presence of moisture. Structural health monitoring was performed on the retrofitted girder, and newly collected strain data were compared to original measurements. Differential scanning calorimetry revealed that the glass transition temperature of both field-cured adhesives was below the 66°C minimum recommended by AASHTO guidelines. Fourier transform infrared spectroscopy indicated minor chemical changes in the field-exposed CFRP. The CFRP system has maintained its bond integrity over two decades; however, in regions where corrosion developed beneath the CFRP, the bond integrity was compromised. This study provides rare, long-term performance data on CFRP–steel retrofits in field conditions and supports their continued use to extend the life of aging steel infrastructure.
- 17 September 2026
- Published by Elsevier in Construction and Building Materials
- Vol. 543
Hygrothermal durability of fiber anchors for externally bonded CFRP strengthening of reinforced concrete members
- 17 September 2026
- Published by Elsevier in Construction and Building Materials
- Vol. 543
Hygrothermal durability of fiber anchors for externally bonded CFRP strengthening of reinforced concrete members
- Top Cited Papers
- 29 January 2025
- Published by Elsevier in Construction and Building Materials
- Vol. 464
Autogenous and drying shrinkage in Ultra-High-Performance Concrete (UHPC) and the effectiveness of internal curing
- 29 January 2025
- Published by Elsevier in Construction and Building Materials
- Vol. 464
Top Cited PapersAutogenous and drying shrinkage in Ultra-High-Performance Concrete (UHPC) and the effectiveness of internal curing
- Open Access
Core–Shell Rubber Nanoparticle-Modified CFRP/Steel Ambient-Cured Adhesive Joints: Curing Kinetics and Mechanical Behavior
Externally bonded wet-layup carbon fiber-reinforced polymer (CFRP) strengthening systems are extensively used in concrete structures but have not found widespread use in deficient steel structures. To address the challenges of the adhesive bonding of wet-layup CFRP to steel substrates, this study investigated the effect of core–shell rubber (CSR) nanoparticles on the curing kinetics, glass transition temperature () and mechanical properties of ambient-cured epoxy/CSR blends. The effects of silane coupling agent and CSR on the adhesive bond properties of CFRP/steel joints were also investigated. The results indicate that CSR nanoparticles have a mild catalytic effect on the curing kinetics of epoxy under ambient conditions. The effect of CSR on the of epoxy was negligible. Epoxy adhesives modified with 5 to 20%wt. of CSR nanoparticles were characterized with improved ductility over brittle neat epoxy; however, the addition of CSR nanoparticles reduced tensile strength and modulus of the adhesives. An up to 250% increase in the single-lap shear strength of CFRP/steel joints was accomplished in CSR-modified joints over neat epoxy adhesive joints.Open AccessCore–Shell Rubber Nanoparticle-Modified CFRP/Steel Ambient-Cured Adhesive Joints: Curing Kinetics and Mechanical Behavior
Externally bonded wet-layup carbon fiber-reinforced polymer (CFRP) strengthening systems are extensively used in concrete structures but have not found widespread use in deficient steel structures. To address the challenges of the adhesive bonding of wet-layup CFRP to steel substrates, this study investigated the effect of core–shell rubber (CSR) nanoparticles on the curing kinetics, glass transition temperature () and mechanical properties of ambient-cured epoxy/CSR blends. The effects of silane coupling agent and CSR on the adhesive bond properties of CFRP/steel joints were also investigated. The results indicate that CSR nanoparticles have a mild catalytic effect on the curing kinetics of epoxy under ambient conditions. The effect of CSR on the of epoxy was negligible. Epoxy adhesives modified with 5 to 20%wt. of CSR nanoparticles were characterized with improved ductility over brittle neat epoxy; however, the addition of CSR nanoparticles reduced tensile strength and modulus of the adhesives. An up to 250% increase in the single-lap shear strength of CFRP/steel joints was accomplished in CSR-modified joints over neat epoxy adhesive joints. - 1 February 2024
- Published by Elsevier in Construction and Building Materials
- Vol. 416
Adhesion of polymer and cementitious overlays to ultra high performance concrete substrate
- 1 February 2024
- Published by Elsevier in Construction and Building Materials
- Vol. 416
Adhesion of polymer and cementitious overlays to ultra high performance concrete substrate
- 15 November 2023
- Published by Taylor & Francis in Structure and Infrastructure Engineering
- Vol. 20 (7-8) , 1149-1158
Diagnostic load testing and assessment of a corroded corrugated metal pipe culvert before rehabilitation
- 15 November 2023
- Published by Taylor & Francis in Structure and Infrastructure Engineering
- Vol. 20 (7-8) , 1149-1158
Diagnostic load testing and assessment of a corroded corrugated metal pipe culvert before rehabilitation