Jens Reuter
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jens Reuter has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
Frank Schönberger
Division Plastics Fraunhofer Institute for Structural Durability and System Reliability LBF Schlossgartenstr. 6, 64289, Darmstadt Germany
1 shared publicationLara Greiner
Division Plastics Fraunhofer Institute for Structural Durability and System Reliability LBF Schlossgartenstr. 6, 64289, Darmstadt Germany
1 shared publicationManfred Döring
Fraunhofer LBF, Darmstadt, Germany
1 shared publication- Manfred Döring
Fraunhofer Institute for Structural Durability and System Reliability LBF, Schlossgartenstr. 6, 64289 Darmstadt, Germany
1 shared publication Tobias Standau
Universität Bayreuth, Bayreuth, Germany
1 shared publication- Volker Altstädt
Polymer Engineering, University of Bayreuth, Bayreuth, Germany
1 shared publication
Latest Publications
- 28 February 2020
- Published by SAGE Publications in Journal of Fire Sciences
- Vol. 38 (3) , 270-283
Flame-retardant hybrid materials based on expandable polystyrene beads
A highly efficient flame-retardant hybrid foam material combining expandable polystyrene foam beads and a waterborne resin equipped with inorganic flame retardants is described. The resin and the inorganic fillers were varied, and the different compositions were investigated in small burner and cone calorimeter tests. The burning time during the small burner test decreases from >60 s for neat expandable polystyrene to 0 s for optimized hybrid specimens. The peak of the heat release rate decreases from 661.0 kW/m2 for neat expandable polystyrene to 121.36 kW/m2 for a hybrid composition of 1:1:1 (expandable polystyrene:aluminum hydroxide:phenol formaldehyde resin). The hybrid materials containing inorganic flame retardants are burning slower and release heat and smoke more constantly at significantly lower rates. Furthermore, a continuous network of the cured thermoset is shown, which leads to embedded expandable polystyrene beads. The flame-retardant thermoset protects the expandable polystyrene from fire and leads to a material with high dimensional stability and efficient flame retardancy.
- 28 February 2020
- Published by SAGE Publications in Journal of Fire Sciences
- Vol. 38 (3) , 270-283
Flame-retardant hybrid materials based on expandable polystyrene beads
A highly efficient flame-retardant hybrid foam material combining expandable polystyrene foam beads and a waterborne resin equipped with inorganic flame retardants is described. The resin and the inorganic fillers were varied, and the different compositions were investigated in small burner and cone calorimeter tests. The burning time during the small burner test decreases from >60 s for neat expandable polystyrene to 0 s for optimized hybrid specimens. The peak of the heat release rate decreases from 661.0 kW/m2 for neat expandable polystyrene to 121.36 kW/m2 for a hybrid composition of 1:1:1 (expandable polystyrene:aluminum hydroxide:phenol formaldehyde resin). The hybrid materials containing inorganic flame retardants are burning slower and release heat and smoke more constantly at significantly lower rates. Furthermore, a continuous network of the cured thermoset is shown, which leads to embedded expandable polystyrene beads. The flame-retardant thermoset protects the expandable polystyrene from fire and leads to a material with high dimensional stability and efficient flame retardancy.
- 23 November 2018
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 136 (13)
Synergistic flame retardant interplay of phosphorus containing flame retardants with aluminum trihydrate depending on the specific surface area in unsaturated polyester resin
The influence of the specific surface area of aluminum trihydrate (ATH) on the synergism to different phosphorus‐based flame retardants (FRs) in unsaturated polyester (UP) resin was investigated. Flammability and thermal stability of UP composites were evaluated with UL‐94 vertical burning, thermogravimetric analysis, and cone calorimetry. The morphology of char residues was examined via scanning electron microscopy (SEM). An interaction between crystalline ATH (4.5 m2 g−1) and aluminum hypophosphite (AHP) or zinc diethylphosphinate (DEPZn) was observed. When 37 wt % ATH and 8 wt % AHP or DEPZn were incorporated, samples passed V‐0 in UL‐94 tests. Furthermore, peak of heat release rate (PHRR) and total heat release (THR) were reduced by introduction of phosphorus containing FRs compared to a formulation containing solely crystalline ATH. The incorporation of amorphous ATH (300 m2 g−1) leaded to lower UL‐94 ratings, using the same amount of AHP or DEPZn. In comparison to crystalline ATH, an addition of phosphorus containing FRs did not lead to a decrease of PHRR and THR for amorphous ATH. SEM of the residues showed that the combination of crystalline ATH with phosphorus species having hydrogen/carbon rich environment formed a dense and tough layer. The combination of crystalline ATH with phosphorus species providing oxygen rich environment gives fragile residues. An incorporation of amorphous ATH leaded to a fragile residue as well. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019, 136, 47270.
- 23 November 2018
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 136 (13)
Synergistic flame retardant interplay of phosphorus containing flame retardants with aluminum trihydrate depending on the specific surface area in unsaturated polyester resin
The influence of the specific surface area of aluminum trihydrate (ATH) on the synergism to different phosphorus‐based flame retardants (FRs) in unsaturated polyester (UP) resin was investigated. Flammability and thermal stability of UP composites were evaluated with UL‐94 vertical burning, thermogravimetric analysis, and cone calorimetry. The morphology of char residues was examined via scanning electron microscopy (SEM). An interaction between crystalline ATH (4.5 m2 g−1) and aluminum hypophosphite (AHP) or zinc diethylphosphinate (DEPZn) was observed. When 37 wt % ATH and 8 wt % AHP or DEPZn were incorporated, samples passed V‐0 in UL‐94 tests. Furthermore, peak of heat release rate (PHRR) and total heat release (THR) were reduced by introduction of phosphorus containing FRs compared to a formulation containing solely crystalline ATH. The incorporation of amorphous ATH (300 m2 g−1) leaded to lower UL‐94 ratings, using the same amount of AHP or DEPZn. In comparison to crystalline ATH, an addition of phosphorus containing FRs did not lead to a decrease of PHRR and THR for amorphous ATH. SEM of the residues showed that the combination of crystalline ATH with phosphorus species having hydrogen/carbon rich environment formed a dense and tough layer. The combination of crystalline ATH with phosphorus species providing oxygen rich environment gives fragile residues. An incorporation of amorphous ATH leaded to a fragile residue as well. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019, 136, 47270.