KSKristina Shea

Kristina Shea

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Kristina Shea has a total of 58 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Experimental performance and spatiotemporal control of solar-powered thermo-pneumatic actuation for adaptive shading in outdoor conditions

    by Rafaela Louis, Kristina Shea

    Adaptive shading systems are an effective strategy for reducing building energy demand and mitigating overheating, which is increasingly critical in the context of the climate crisis. While many adaptive façade systems rely on active control, electronics and external power, these approaches add complexity, embodied emissions, and operational energy use. Passively controlled adaptive shading (PCAS) offers a low-energy alternative, yet existing solutions are commonly based on material-driven actuation and respond primarily to ambient temperature or humidity. This constrains their capability to react to short-term changes in sky conditions, localized context shading, and can restrict actuation to only specific seasons. This study experimentally investigates solar-powered, thermo-pneumatic actuation as an irradiance-responsive driver for PCAS in outdoor conditions. A window-scale prototype comprising nine modular shading devices is developed, in which solar-heated air expansion generates pneumatic actuation. The system is equipped with sensors to monitor environmental conditions and shading behavior during clear and changing sky conditions. The results validate the general functionality of the system by demonstrating fully autonomous opening and closing behavior throughout the day. The shading response is shown to respond to solar irradiance rather than ambient temperature alone, confirming irradiance sensitivity with reaction times on the order of 15 min and reopening during overcast conditions under stable air temperatures. Further, a multi-collector configuration demonstrates passive spatiotemporal control through solar collector chamber orientation, enabling time-dependent and spatially coordinated shading behavior without active control electronics. The reported studies provide outdoor experimental insights on solar-powered thermo-pneumatic actuation and identify key passive control parameters, highlighting its potential as a low-energy and low-emission approach for creating adaptive building façades in new and existing buildings.

  • Open Access

    Computational design synthesis of multi-state, 4D printed, architected active composites

    by Andreas Walker, Kristina Shea

    4D printing, the process of additively manufacturing active materials, enables the assembly-free creation of stimuli-responsive systems that would usually require sensors, actuators, structural components and control systems. Computational design methods have been proposed to help designers navigate the complex relations between material distribution and structural behavior to design shape morphing structures. However, they either neglect mechanical loads or demonstrate only small shape changes. This intersection is of particular relevance since large shape changes are often essential to change the function of a design, e.g. to change the shape so that a structure can form a hook that can be mechanically loaded. In this paper, a computational design method is proposed that can design structures that undergo two targeted shape changes, one in response to environmental actuation and a subsequent one in response to mechanical loading. The foundation for this approach is a library of parametrized Unit Cell (UC) architectures that have adjustable mechanical properties and stimulus responses that strongly differ from those of the constituent materials. A custom genetic algorithm is used to optimize a design composed of UCs such that the resulting structure shows the desired behavior. The method is applied to three case studies, demonstrating that design solutions are found that not only deform in response to environmental actuation, but also show a targeted shape change in response to subsequent mechanical loading. Overall, the method makes the technological potential of 4D printing more available to designers by enabling a means for computational, systematic exploration of the vast design space.


  • Open Access

    Redeployable, 4D printed wave spring actuators

    by Joël N. Chapuis, Kristina Shea


  • Computational Design of Multi-State Lattice Structures With Finite Mechanisms for Shape Morphing

    by Thomas S. Lumpe, Kristina Shea

    Shape-morphing structures are beneficial for applications in aerospace, automotive, and architecture since they allow structures to adapt to changing environmental conditions. Finding structural configurations with intrinsic shape-morphing capabilities is, however, difficult due to the complexity of enabling and controlling target deformations while at the same time maintaining structural integrity. Existing solutions are often unstable, hard to fabricate, or limited to a single target state. Here, we show how lattice structures can be designed that morph from an initial state to one or multiple target states with a single kinematic degrees-of-freedom. Thus, the deformations of a structure can be fully controlled by controlling a single input node for every state. Since the structures are designed at the verge of kinematic determinacy, they become statically and kinematically determinate and hence load-carrying upon fixing the actuation node. As all deformations are described by inextensional mechanism modes, the kinematic and mechanical performance of the structures are decoupled and can be tuned individually. We further show that not only the target shape of a structure can be controlled, but also the kinematic path of a target node between its initial and its final position. The results are verified by fabricating the designs using multi-material 3D printing that enables direct fabrication of complex joints. Our work combines advantages of load-carrying lattice structures and distinct topological and geometric design to generate integrated kinematic solutions for a wide range of applications such as morphing wings, robotic grippers, and adaptive building facades.


  • Co-Design of the Morphology and Actuation of Soft Robots for Locomotion

    by Merel van Diepen, Kristina Shea

    In recent years, the field of soft robotics has received considerable attention due to its potential in increasing the safety of human-robot interaction. The design of soft robots possesses great challenges. For example, the longstanding challenge of co-design morphology and actuation makes designing them by hand a trial-and-error process. Earlier work presented by the authors proposes a computational design synthesis (CDS) method for the automated design of virtual, soft locomotion robot morphologies. This work extends the CDS method for morphologies with the automated co-design of actuation. Two methods are considered. In the first method, the actuation of designs is described by parametric actuation curves (PACs) that model feedforward actuation patterns. For every morphology in the design process, a set of PACs is optimized that assumes symmetric and cyclic gaits. The second method, soft actor-critic (SAC) reinforcement learning, removes this assumption as well as models feedback control for comparison. Adding PAC optimization to the CDS method is shown to improve the performance of the resulting designs and to achieve better results within less design iterations. SAC is, however, deemed less effective, due to the need for design specific problem tuning for each new morphology. The SAC experiments also show that the best found soft robot gaits are symmetric and cyclic, although this is not a constraint in the SAC problem formulation, thus verifying the assumptions made in the PAC formulation. To validate the search space modeled in the co-design CDS method, a state-of-the-art soft robot is replicated and compared.


  • Open Access

    Industrial evaluation of design heuristics for additive manufacturing

    by Alexandra Blösch-Paidosh, Kristina Shea

    Additive manufacturing (AM) has gained prominence over the last 15 years and become a viable manufacturing option. Since there is great industrial interest to implement serial production of products using AM, the education of engineers in design for additive manufacturing (DfAM) is important today. DfAM extends on design for manufacturing to provide knowledge about the new design opportunities enabled by AM. A set of design heuristics for additive manufacturing (DHAM) to assist designers with conceptual-level DfAM has previously been proposed. In this paper, these DHAM are evaluated through workshops with 3 engineering companies and 19 engineers, in which the participants re-design existing company products for AM using the DHAM as an aid, and then give feedback. The DHAM are well received by the workshop participants, and they find that the DHAM are good for teaching others about the capabilities of AM, provide a checklist of items to consider to help avoid oversights, and encourage the generation of new ideas. Criticisms include the number of examples provided and the lack of information about how to implement the ideas concretely. It is also found that the DHAM fulfil 16 of 18 criteria for early design phase DfAM methods, identified in academic literature.


  • Open Access

    Validation of a nonlinear force method for large deformations in shape-morphing structures

    by Cosima du Pasquier, Kristina Shea

    Reducing energy and material consumption is a priority for the construction, aerospace, and automotive industries. Shape morphing addresses these concerns by broadening the band of functionality of a structure by adapting its shape to an external stimulus, such as pressure, or an internal stimulus, such as embedded actuation. This work outlines the development of an actuator placement optimization method for overdeterminate lattice structures with the objective of achieving predetermined large shape changes accurately. The deformation is modeled with both a linear and a nonlinear force method to determine their validity for large-shape change and their usefulness for the field of shape morphing. The linear and nonlinear methods are compared in four benchmark problems and two case studies relevant to the field of shape morphing. The nonlinear method is shown to achieve a level of accuracy $$10^2$$ 10 2 to $$10^4$$ 10 4 higher compared to FEM simulation, while using 23% fewer actuators and up to 77.3% less elongation of actuators, which makes it more favorable for shape-morphing applications. Two case studies for applications in aerospace and construction show that the nonlinear force method is better equipped for large shape change in overdeterminate meshed freeform target shapes and doubly curved surfaces with a high variable density. However, the nonlinear force method is less computationally efficient than the linear force method, as expected. A judicious choice of constraints can help reduce the run time.


  • A Computational Design Synthesis Method for the Generation of Rigid Origami Crease Patterns

    by Luca Zimmermann, Kristina Shea, Tino Stanković

    Today most origami crease patterns used in technical applications are selected from a handful of well-known origami principles. Computational algorithms capable of generating novel crease patterns either target artistic origami, focus on quadrilateral creased paper, or do not incorporate direct knowledge for the purposeful design of crease patterns tailored to engineering applications. The lack of computational methods for the generative design of crease patterns for engineering applications arises from a multitude of geometric complexities intrinsic to origami, such as rigid foldability and rigid body modes (RBMs), many of which have been addressed by recent work of the authors. Based on these findings, in this paper we introduce a Computational Design Synthesis (CDS) method for the generative design of novel crease patterns to develop origami concepts for engineering applications. The proposed method first generates crease pattern graphs through a graph grammar that automatically builds the kinematic model of the underlying origami and introduces constraints for rigid foldability. Then, the method enumerates all design alternatives that arise from the assignment of different rigid body modes to the internal vertices. These design alternatives are then automatically optimized and checked for intersection to satisfy the given design task. The proposed method is generic and applied here to two design tasks that are a rigidly foldable gripper and a rigidly foldable robotic arm.


  • Systematic Design, Control, and Parametric Testing of an Automated Resuscitator Bag Mechanical Ventilator

    by Cosima du Pasquier, Lukas Hewing, Nicola Steffen, Thomas S. Lumpe, Nikolaos Tatchatos, Marcel Menner, Marianne Schmid Daners, Andrea Carron, Melanie N. Zeilinger, Kristina Shea

    The COVID-19 crisis has revealed and exacerbated a shortage of mechanical ventilators in hospitals around the world, regardless of their government’s resources. Where some countries can respond to the situation by ordering more high-end ventilators, the price is often too high for low- and middle-income countries (LMICs) and securing them can be difficult. The goal of this work is to design, prototype, and test a low-cost ventilator, called ETH breathe, based on the automated compression of a resuscitator bag. A holistic and systematic design approach is taken to create a compact and adaptable device that can safely meet the current requirements. This is achieved by using 72% standard parts out of 33 (72%) and prioritizing compactness in the mechanical design. The control system is developed to provide both continuous mandatory ventilation (CMV) and spontaneous breathing support or assist control (AC), which significantly extends the potential use cases beyond patient sedation. The prototype is tested for accuracy, modularity, and oxygen response using a full physiological artificial lung. The results show for the first time in literature that the design operates within the defined requirements, based on emergency government regulations, and can be used with different sizes of resuscitator bags and different positions of the flow sensor. This provides a sound basis for further development of a low-cost, portable mechanical ventilator for potential use in LMICs.