Laurence Lutsen

Organic electrochemical transistors (OECTs) enable the transduction of ionic signals into electronic outputs, positioning them as ideal candidates for next-generation sensing and (bio)signal processing applications. Recent years have witnessed the development of various OECT channel materials, affording insights on structural fine-tuning to achieve optimal performance and/or stability. However, homocouplings, commonly present in alternating conjugated polymers, have largely been overlooked. This study investigates the effect of homocoupling on OECT materials by employing two synthesis methods – standard Stille polymerization and an alternative symmetric approach – to create the p-type enhancement-mode benchmark polymer pgBTTT. The impact of homocoupling, and its absence, is studied by comparing the bulk properties of the two polymers and evaluating their respective OECT metrics. The new, homocoupling-free polymer exhibits a notably improved OECT performance (μC*), mainly due to an increase in electronic mobility (μ), which is attributed to both the perfectly alternating structure and its higher molar mass.

Recently, the efficiency of p‐i‐n perovskite solar cells drastically increased, a pivotal factor being the incorporation of self‐assembled monolayers (SAMs) as a hole‐transporting layer (HTL). SAMs offer many advantages over conventional HTLs, including minimal material requirements, low cost, and facile processing. Current research is mainly focused on the development of carbazole‐derived SAMs. However, the versatility of organic chemistry allows for the design of SAMs with alternative organic cores that may possess specific benefits. In this study, three novel SAMs are incorporated in p‐i‐n perovskite solar cells, each based on an aromatic core commonly used in organic semiconductors. The novel SAMs vary in their energy level alignment with the perovskite active layer. Optimal alignment is achieved with a pyrene‐based SAM (4PAPyr), resulting in solar cells that outperform the commercially available 2PACz. Moreover, due to improved surface coverage, the use of 4PAPyr leads to a significantly higher number of working solar cell devices when compared to 2PACz, which is of particular interest with regard to upscaling. After device optimization, a power conversion efficiency of 22.2% is achieved with 4PAPyr. This research underlines the importance of diversifying SAMs to unlock further advancements in perovskite solar cell efficiency and scalability.

This study reports on the first all‐printed vertically stacked organic electrochemical transistors (OECTs) operating in accumulation mode; the devices, relying on poly([4,4′‐bis(2‐(2‐(2‐methoxyethoxy)ethoxy)ethoxy)‐2,2′‐bithiophen‐5,5′‐diyl]‐alt‐[thieno[3,2‐b]thiophene‐2,5‐diyl]) (pgBTTT) as the active channel material, are fabricated via a combination of screen and inkjet printing technologies. The resulting OECTs (W/L ≈5) demonstrate good switching performance; g_{m, norm} ≈13 mS cm⁻¹, µC* ≈21 F cm⁻¹ V⁻¹ s⁻¹, ON–OFF ratio > 10⁴ and good cycling stability upon continuous operation for 2 h. The inkjet printing process of pgBTTT is established by first solubilizing the polymer in dihydrolevoglucosenone (Cyrene), a non‐toxic, cellulose‐derived, and biodegradable solvent. The resulting ink formulations exhibit good jettability, thereby providing reproducible and stable p‐type accumulation mode all‐printed OECTs with high performance. Besides the environmental and safety benefits of this solvent, this study also demonstrates the assessment of how the solvent affects the performance of spin‐coated OECTs, which justifies the choice of Cyrene as an alternative to commonly used harmful solvents such as chloroform, also from a device perspective. Hence, this approach shows a new possibility of obtaining more sustainable printed electronic devices, which will eventually result in all‐printed OECT‐based logic circuits operating in complementary mode.

Ladder-type extension of a push–pull donor polymer affords enhanced peak external quantum efficiencies in microcavity organic photodetectors, with detectivities ranging from 1.07 × 10¹² to 1.82 × 10¹⁰ Jones in the 900–1400 nm regime.

The true structure of alternating conjugated polymers—the state‐of‐the‐art materials for many organic electronics—often deviates from the idealized picture. Homocoupling defects are in fact inherent to the widely used cross‐coupling polymerization methods. Nevertheless, many polymers still perform excellently in the envisaged applications, which raises the question if one should really care about these imperfections. This article looks at the relevance of chemical precision (and lack thereof) in conjugated polymers covering the entire spectrum from the molecular scale, to the micro and mesostructure, up to the device level. The different types of polymerization errors for the alkoxylated variant of the benchmark (semi)crystalline polymer poly[2,5‐bis(3‐tetradecylthiophen‐2‐yl)thieno[3,2‐b]thiophene (PBTTT) are identified, visualized, and quantified and a general strategy to avoid homocoupling is introduced. Through a combination of experiments and supported by simulations, it is shown that these coupling defects hinder fullerene intercalation and limit device performance as compared to the homocoupling‐free analog. This clearly demonstrates that structural defects do matter and should be generally avoided, in particular when the geometrical regularity of the polymer is essential. These insights likely go beyond the specific PBTTT derivatives studied here and are of general relevance for the wider organic electronics field.

Highly performing mixed Sn/Pb-metal halide perovskite solar cells (PSCs) are among the most promising options to reduce Pb content in perovskite devices and enable, owing to their reduced bandgap, the fabrication of all-perovskite tandem solar cells. Whereas pure-Pb perovskite devices exhibit efficiency up to 25.5%, alongside a high open-circuit voltage (≈1.2 V), Sn-Pb PSCs still show lower performances (22.2%) due to higher open-circuit voltage losses. Here, we introduced 2,3,4,5,6-pentafluorophenethylammonium cations in a perovskite active layer of composition (FASnI₃)_0.5(MAPbI₃)_0.5 to obtain highly oriented films with improved thermal stability. The treated films exhibit merged grains with no evidence of 2D structures, which could help to reduce the trap state density at the surface and grain boundaries. Solar cells fabricated with the fluorinated cation added to the active layer displayed reduced trap-assisted recombination losses and lower background carrier density, which leads to enhanced open-circuit voltages with respect to the reference samples and the active layers incorporating unfluorinated phenethylammonium cations. The best device reached an efficiency of 19.13%, with an open-circuit voltage of 0.84 V, which is substantially improved with respect to the reference sample showing 17.47% efficiency and 0.77 V open-circuit voltage. More importantly, the fluorinated cations' addition is instrumental to improve the device's thermal stability; 90.3% of the solar cell initial efficiency is maintained after 90 min of thermal stress at 85 °C in a nitrogen atmosphere.

In this perspective, we give an overview of the key historic achievements, the state-of-the-art, and future perspectives of flow chemistry applied to the synthesis of conjugated polymers for organic electronics.