Alicia López
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Alicia López has a total of 35 co-authors. Here are the top co-authors by number of shared publications:
- Maria Angeles Losada
Photonics Technology Group (GTF), Communications Networks and Information Tecnhologies Group (CeNIT), Aragn Institute of Engineering Research (i3A), University of Zaragoza, Zaragoza, Spain
12 shared publications - Javier Mateo
GTF, Aragon Institute of Engineering Research (i3A), University of Zaragoza, María de Luna 1, E-50018 Zaragoza, Spain
9 shared publications - Dwight Richards
Department of Engineering and Environmental Science, College of Staten Island, CUNY, 2800 Victory Blvd., Staten island, NY 10314, USA
5 shared publications - Xin Jiang
Department of Engineering and Environmental Science, College of Staten Island, CUNY, 2800 Victory Blvd., Staten island, NY 10314, USA
5 shared publications - Neophytos Antoniades
College of Staten Island/The City University of New York
4 shared publications - Juan José Martínez
Aragon Photonics Labs (APL) SLU, Zaragoza, Spain
3 shared publications
Latest Publications
- Open Access
- 20 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Internet of Things Journal
- Vol. 13 (10) , 21799-21810
Highly Linear IoT-Over-Plastic Optical Fiber Transmission With Low-Complexity Cluster-Based Predistortion
In the context of ultralow-end applications such as smart homes, smart vehicles, and the industrial Internet of Things (IIoT), the use of plastic optical fibers (POFs) as a communications backbone to enable the convergence of wireless and optical systems has emerged as a cost-effective and ruggedized solution. The transmission of standalone narrowband IoT (NB-IoT) signals through large-core step-index POF (SI-POF) can be achieved by directly modulating a laser diode (LD) at the cost of introducing nonlinear effects. In this work, the performance of a radio-over-POF (RoPOF) link is enhanced by digital predistortion (DPD) using a memoryless polynomial approach whose complexity is reduced by scaling down the number of samples using a novel technique that preserves the data statistics by organizing the data into a number of clusters.
- 20 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Internet of Things Journal
- Vol. 13 (10) , 21799-21810
Open AccessHighly Linear IoT-Over-Plastic Optical Fiber Transmission With Low-Complexity Cluster-Based Predistortion
In the context of ultralow-end applications such as smart homes, smart vehicles, and the industrial Internet of Things (IIoT), the use of plastic optical fibers (POFs) as a communications backbone to enable the convergence of wireless and optical systems has emerged as a cost-effective and ruggedized solution. The transmission of standalone narrowband IoT (NB-IoT) signals through large-core step-index POF (SI-POF) can be achieved by directly modulating a laser diode (LD) at the cost of introducing nonlinear effects. In this work, the performance of a radio-over-POF (RoPOF) link is enhanced by digital predistortion (DPD) using a memoryless polynomial approach whose complexity is reduced by scaling down the number of samples using a novel technique that preserves the data statistics by organizing the data into a number of clusters.
- 5 November 2025
- Published by Springer Nature in Optical and Quantum Electronics
- Vol. 57 (11) , 1-19
Computational modeling of PMMA-POFs for system-level infrastructure applications
- 5 November 2025
- Published by Springer Nature in Optical and Quantum Electronics
- Vol. 57 (11) , 1-19
Computational modeling of PMMA-POFs for system-level infrastructure applications
- Open Access
- 11 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of the Communications Society
- Vol. 6, 6258-6280
Understanding the Potentials of Narrowband Internet of Things (NB-IoT) Cellular Technology: Salient Features, Architecture, Smart Applications and Quality of Service (QoS) Challenges
Since the last decade, the number of Internet of Things (IoT) devices has increased dramatically and to operate them at low power has been a great challenge. Therefore, significant efforts have been made by the researchers to innovate such technologies that may operate the IoT devices at low power. In this context, several Low Power Wide Area Network (LPWAN) technologies have been introduced which have revolutionized the world of IoT. Narrowband Internet of Things (NB-IoT) is one of the protocols that was developed by 3rd Generation Partnership Project (3GPP) in June 2016 to cater the stringent requirements of IoT devices. In this paper, a comprehensive analysis on the features, architecture, signals and channels of NB-IoT is provided. Additionally, a detailed description of the applications of NB-IoT is also presented. Finally, some crucial challenges related to the quality of service (QoS) of NB-IoT are highlighted in this paper.
- 11 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of the Communications Society
- Vol. 6, 6258-6280
Open AccessUnderstanding the Potentials of Narrowband Internet of Things (NB-IoT) Cellular Technology: Salient Features, Architecture, Smart Applications and Quality of Service (QoS) Challenges
Since the last decade, the number of Internet of Things (IoT) devices has increased dramatically and to operate them at low power has been a great challenge. Therefore, significant efforts have been made by the researchers to innovate such technologies that may operate the IoT devices at low power. In this context, several Low Power Wide Area Network (LPWAN) technologies have been introduced which have revolutionized the world of IoT. Narrowband Internet of Things (NB-IoT) is one of the protocols that was developed by 3rd Generation Partnership Project (3GPP) in June 2016 to cater the stringent requirements of IoT devices. In this paper, a comprehensive analysis on the features, architecture, signals and channels of NB-IoT is provided. Additionally, a detailed description of the applications of NB-IoT is also presented. Finally, some crucial challenges related to the quality of service (QoS) of NB-IoT are highlighted in this paper.
- Open Access
- 9 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 41 (23) , 7302-7308
Cellular Guardband NB-IoT Performance Over PMMA Plastic Optical Fibers
Over the last decade, the growing demand of connectivity has produced a rapid evolution of 5G technology to answer the requirements of relevant areas such as Internet of Things (IoT). Radio and optical technology convergence appears as a solution to fulfill the needs of the future networks, exploiting the high bandwidth-range of optical fibers with the ubiquity and mobility of radio communications. The concept of Radio-over-Fiber has usually been applied successfully using silica fibers to transmit light from a modulated laser to a photodetector for demanding applications. In this work, we propose to evaluate the performance of Polymer Optical Fiber (POF) links to carry RF signals for those applications where their limited bandwidth-length product is sufficient, while their fast and cost-effective deployment is paramount. In particular, we analyze the performance of the downlink transmission of Long Term Evolution (LTE) and guardband Narrow-Band Internet of Things (NB-IoT) signals through a 75-m Poly(methyl methacrylate) – PMMA Graded-Index POF. Our study considers a comprehensive set of LTE carrier frequencies and bandwidths.
- 9 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 41 (23) , 7302-7308
Open AccessCellular Guardband NB-IoT Performance Over PMMA Plastic Optical Fibers
Over the last decade, the growing demand of connectivity has produced a rapid evolution of 5G technology to answer the requirements of relevant areas such as Internet of Things (IoT). Radio and optical technology convergence appears as a solution to fulfill the needs of the future networks, exploiting the high bandwidth-range of optical fibers with the ubiquity and mobility of radio communications. The concept of Radio-over-Fiber has usually been applied successfully using silica fibers to transmit light from a modulated laser to a photodetector for demanding applications. In this work, we propose to evaluate the performance of Polymer Optical Fiber (POF) links to carry RF signals for those applications where their limited bandwidth-length product is sufficient, while their fast and cost-effective deployment is paramount. In particular, we analyze the performance of the downlink transmission of Long Term Evolution (LTE) and guardband Narrow-Band Internet of Things (NB-IoT) signals through a 75-m Poly(methyl methacrylate) – PMMA Graded-Index POF. Our study considers a comprehensive set of LTE carrier frequencies and bandwidths.
- Open Access
Novel Measurement-Based Efficient Computational Approach to Modeling Optical Power Transmission in Step-Index Polymer Optical Fiber
Polymer optical fibers (POFs) are playing an important role in industrial applications nowadays due to their ease of handling and resilience to bending and environmental effects. A POF can tolerate a bending radius of less than 20 mm, it can work in environments with temperatures ranging from −55 °C to +105 °C, and its lifetime is around 20 years. In this paper, we propose a novel, rigorous, and efficient computational model to estimate the most important parameters that determine the characteristics of light propagation through a step-index polymer optical fiber (SI-POF). The model uses attenuation, diffusion, and mode group delay as functions of the propagation angle to characterize the optical power transmission in the SI-POF. Taking into consideration the mode group delay allows us to generalize the computational model to be applicable to POFs with different index profiles. In particular, we use experimental measurements of spatial distributions and frequency responses to derive accurate parameters for our SI-POF simulation model. The experimental data were measured at different fiber lengths according to the cut-back method. This method consists of taking several measurements such as frequency responses, angular intensity distributions, and optical power measurements over a long length of fiber (>100 m), then cutting back the fiber while maintaining the same launching conditions and repeating the measurements on the shorter lengths of fiber. The model derivation uses an objective function to minimize the differences between the experimental measurements and the simulated results. The use of the matrix exponential method (MEM) to implement the SI-POF model results in a computationally efficient model that is suitable for POF-based system-level studies. The efficiency gain is due to the independence of the calculation time with respect to the fiber length, in contrast to the classic analytical solutions of the time-dependent power flow equation. The robustness of the proposed model is validated by calculating the goodness-of-fit of the model predictions relative to experimental data.
Open AccessNovel Measurement-Based Efficient Computational Approach to Modeling Optical Power Transmission in Step-Index Polymer Optical Fiber
Polymer optical fibers (POFs) are playing an important role in industrial applications nowadays due to their ease of handling and resilience to bending and environmental effects. A POF can tolerate a bending radius of less than 20 mm, it can work in environments with temperatures ranging from −55 °C to +105 °C, and its lifetime is around 20 years. In this paper, we propose a novel, rigorous, and efficient computational model to estimate the most important parameters that determine the characteristics of light propagation through a step-index polymer optical fiber (SI-POF). The model uses attenuation, diffusion, and mode group delay as functions of the propagation angle to characterize the optical power transmission in the SI-POF. Taking into consideration the mode group delay allows us to generalize the computational model to be applicable to POFs with different index profiles. In particular, we use experimental measurements of spatial distributions and frequency responses to derive accurate parameters for our SI-POF simulation model. The experimental data were measured at different fiber lengths according to the cut-back method. This method consists of taking several measurements such as frequency responses, angular intensity distributions, and optical power measurements over a long length of fiber (>100 m), then cutting back the fiber while maintaining the same launching conditions and repeating the measurements on the shorter lengths of fiber. The model derivation uses an objective function to minimize the differences between the experimental measurements and the simulated results. The use of the matrix exponential method (MEM) to implement the SI-POF model results in a computationally efficient model that is suitable for POF-based system-level studies. The efficiency gain is due to the independence of the calculation time with respect to the fiber length, in contrast to the classic analytical solutions of the time-dependent power flow equation. The robustness of the proposed model is validated by calculating the goodness-of-fit of the model predictions relative to experimental data.
- Open Access
Experimental Assessment of the Transmission Performance of Step Index Polymer Optical Fibers Using a Green Laser Diode
Large-core polymer optical fiber (POF) links have limitations in capacity and reach due to the fibers’ high modal dispersion and attenuation. Most of these links use red laser diodes, even though the attenuation spectrum of poly(methyl methacrylate) (PMMA), the basic polymer used to manufacture these fibers, has a lower minimum in the green region. Therefore, we set out to explore the potential use of green light in transmission systems, comparing the performances of three step-index polymer optical fibers (SI-POFs) with different numerical apertures. We obtained measurements of intensity distribution, frequency response and bit error rate (BER), as functions of fiber length. We have also compared the fibers’ frequency responses with red and green light for a few selected lengths. Our results confirm that SI-POFs attenuate less in response to green light, which can increase their length. This advantage is partially counterbalanced by a slightly higher dispersion that limits the capacity of the high-aperture fibers, particularly at relatively short lengths. Our conclusions are critical to understanding SI-POF behavior and to designing thorough SI-POF models that can aid the design of POF-based links for different scenarios.
Open AccessExperimental Assessment of the Transmission Performance of Step Index Polymer Optical Fibers Using a Green Laser Diode
Large-core polymer optical fiber (POF) links have limitations in capacity and reach due to the fibers’ high modal dispersion and attenuation. Most of these links use red laser diodes, even though the attenuation spectrum of poly(methyl methacrylate) (PMMA), the basic polymer used to manufacture these fibers, has a lower minimum in the green region. Therefore, we set out to explore the potential use of green light in transmission systems, comparing the performances of three step-index polymer optical fibers (SI-POFs) with different numerical apertures. We obtained measurements of intensity distribution, frequency response and bit error rate (BER), as functions of fiber length. We have also compared the fibers’ frequency responses with red and green light for a few selected lengths. Our results confirm that SI-POFs attenuate less in response to green light, which can increase their length. This advantage is partially counterbalanced by a slightly higher dispersion that limits the capacity of the high-aperture fibers, particularly at relatively short lengths. Our conclusions are critical to understanding SI-POF behavior and to designing thorough SI-POF models that can aid the design of POF-based links for different scenarios.
- Open Access
Sensing Applications in Aircrafts Using Polymer Optical Fibres
We report on recent advances in the use of inexpensive polymer optical fibres (POFs) for sensing applications in avionics. The sensors analysed in this manuscript take advantage of the unique properties of polymers, such as high flexibility, elasticity, and sensitivity, and they range from strain, elongation, and vibration interrogators to level and temperature meters, leading to cost-effective techniques for structural health monitoring in aircraft structures. We also highlight recent power-supply methods using Power-over-POF in order to feed sensors remotely, and we discuss the constraints imposed by connectors on the performance of POF networks in aircrafts.
Open AccessSensing Applications in Aircrafts Using Polymer Optical Fibres
We report on recent advances in the use of inexpensive polymer optical fibres (POFs) for sensing applications in avionics. The sensors analysed in this manuscript take advantage of the unique properties of polymers, such as high flexibility, elasticity, and sensitivity, and they range from strain, elongation, and vibration interrogators to level and temperature meters, leading to cost-effective techniques for structural health monitoring in aircraft structures. We also highlight recent power-supply methods using Power-over-POF in order to feed sensors remotely, and we discuss the constraints imposed by connectors on the performance of POF networks in aircrafts.
- Open Access
Overcoming Challenges in Large-Core SI-POF-Based System-Level Modeling and Simulation
The application areas for plastic optical fibers such as in-building or aircraft networks usually have tight power budgets and require multiple passive components. In addition, advanced modulation formats are being considered for transmission over plastic optical fibers (POFs) to increase spectral efficiency. In this scenario, there is a clear need for a flexible and dynamic system-level simulation framework for POFs that includes models of light propagation in POFs and the components that are needed to evaluate the entire system performance. Until recently, commercial simulation software either was designed specifically for single-mode glass fibers or modeled individual guided modes in multimode fibers with considerable detail, which is not adequate for large-core POFs where there are millions of propagation modes, strong mode coupling and high variability. These are some of the many challenges involved in the modeling and simulation of POF-based systems. Here, we describe how we are addressing these challenges with models based on an intensity-vs-angle representation of the multimode signal rather than one that attempts to model all the modes in the fiber. Furthermore, we present model approaches for the individual components that comprise the POF-based system and how the models have been incorporated into system-level simulations, including the commercial software packages SimulinkTM and ModeSYSTM.
Open AccessOvercoming Challenges in Large-Core SI-POF-Based System-Level Modeling and Simulation
The application areas for plastic optical fibers such as in-building or aircraft networks usually have tight power budgets and require multiple passive components. In addition, advanced modulation formats are being considered for transmission over plastic optical fibers (POFs) to increase spectral efficiency. In this scenario, there is a clear need for a flexible and dynamic system-level simulation framework for POFs that includes models of light propagation in POFs and the components that are needed to evaluate the entire system performance. Until recently, commercial simulation software either was designed specifically for single-mode glass fibers or modeled individual guided modes in multimode fibers with considerable detail, which is not adequate for large-core POFs where there are millions of propagation modes, strong mode coupling and high variability. These are some of the many challenges involved in the modeling and simulation of POF-based systems. Here, we describe how we are addressing these challenges with models based on an intensity-vs-angle representation of the multimode signal rather than one that attempts to model all the modes in the fiber. Furthermore, we present model approaches for the individual components that comprise the POF-based system and how the models have been incorporated into system-level simulations, including the commercial software packages SimulinkTM and ModeSYSTM.
- Open Access
Characterization of a Y-Coupler and Its Impact on the Performance of Plastic Optical Fiber Links
Couplers and splitters are common devices in single-mode and multi-mode glass fibers applications, where they perform a variety of functions. However, when switching to plastic optical fibers (POFs), there is a shortage of commercial devices, which are usually custom-made. The problem with these devices is that modal power distribution in POFs is easily modified by spatial disturbances that produce a localized strong power transfer between modes, thus changing their transmission properties. In this work, a commercial Y-coupler designed for POFs is experimentally characterized. Measurements of its spectral, spatial and temporal characteristics have been performed, including insertion loss as a function of wavelength, angular power distribution, and frequency response. The obtained results show that this device has an equalizing effect over the power spatial distribution that reduces the fiber bandwidth, demonstrating the importance of considering the impact of this type of devices on the transmission properties of any POF system.
Open AccessCharacterization of a Y-Coupler and Its Impact on the Performance of Plastic Optical Fiber Links
Couplers and splitters are common devices in single-mode and multi-mode glass fibers applications, where they perform a variety of functions. However, when switching to plastic optical fibers (POFs), there is a shortage of commercial devices, which are usually custom-made. The problem with these devices is that modal power distribution in POFs is easily modified by spatial disturbances that produce a localized strong power transfer between modes, thus changing their transmission properties. In this work, a commercial Y-coupler designed for POFs is experimentally characterized. Measurements of its spectral, spatial and temporal characteristics have been performed, including insertion loss as a function of wavelength, angular power distribution, and frequency response. The obtained results show that this device has an equalizing effect over the power spatial distribution that reduces the fiber bandwidth, demonstrating the importance of considering the impact of this type of devices on the transmission properties of any POF system.
- Open Access
- 12 July 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 36 (21) , 5082-5088
Transmission Performance of Plastic Optical Fibers Designed for Avionics Platforms
Plastic Optical Fibers have been proposed and implemented in the avionics environment lately and temperature is naturally a big factor that can affect their performance in those platforms. We present an experimental characterization of the transmission properties of plastic optical fibers (POFs) comparing the performance of standard fibers with that of fibers designed to sustain high temperatures, such as those on avionics platforms. We tested different step-index 1 mm PMMA single-core (SC) and multi-core (MC) fibers. Frequency response, bit error rate (BER), attenuation and output power distribution were measured for each fiber type at room temperature. In addition, BER and fiber attenuation were monitored as a function of temperature, intentionally exceeding the temperature limits to obtain the true temperature ranges and to assess the performance penalty. The same properties were obtained for the over-heated fibers and compared to those for non-heated fibers of the same type to reveal permanent performance degradation.
- 12 July 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 36 (21) , 5082-5088
Open AccessTransmission Performance of Plastic Optical Fibers Designed for Avionics Platforms
Plastic Optical Fibers have been proposed and implemented in the avionics environment lately and temperature is naturally a big factor that can affect their performance in those platforms. We present an experimental characterization of the transmission properties of plastic optical fibers (POFs) comparing the performance of standard fibers with that of fibers designed to sustain high temperatures, such as those on avionics platforms. We tested different step-index 1 mm PMMA single-core (SC) and multi-core (MC) fibers. Frequency response, bit error rate (BER), attenuation and output power distribution were measured for each fiber type at room temperature. In addition, BER and fiber attenuation were monitored as a function of temperature, intentionally exceeding the temperature limits to obtain the true temperature ranges and to assess the performance penalty. The same properties were obtained for the over-heated fibers and compared to those for non-heated fibers of the same type to reveal permanent performance degradation.