Silvester Sadjina
Research Subjects
Silvester Sadjina has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Harald Pretl
Johannes Kepler University, Linz, Austria
6 shared publications - Mario Huemer
Institute of Signal Processing, Johannes Kepler University, Linz, Austria
5 shared publications Ram Sunil Kanumalli
Intel DMCE, Linz, Austria
3 shared publications- Andreas Gebhard
DMCE, Linz, Austria
2 shared publications - Christian Motz
Christian Doppler Laboratory for Digitally Assisted RF Transceivers for Future Mobile Communications, Institute of Signal Processing, Johannes Kepler University Linz, Linz, Austria
2 shared publications Krzysztof Dufrene
Intel DMCE, Linz, Austria
2 shared publications
Latest Publications
- 8 September 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 68 (3) , 923-927
A Robust Mixed-Signal Cancellation Approach for Even-Order Intermodulation Distortions in LTE-A/5G-Transceivers
State-of-the-art radio frequency receivers for mobile communications inevitably show nonlinearities, mainly caused by constraints in the analog design of the low-noise amplifier and the mixer. In the widely-used direct-conversion architecture, especially even-order intermodulation products cause interference in the baseband, thereby severely deteriorating the receiver signal-to-noise ratio. While several proposed methods aim to cancel second-order distortions caused by transmitter self-interference, the mitigation of higher-order effects is rarely covered. In this work, we present a novel scalable mixed-signal approach for cancellation of intermodulation distortions up to the sixth order. The interference signal is captured by means of an auxiliary receiver, which also allows to suppress interferences caused by external sources. The auxiliary receive signal serves as a basis for a real-time capable digital processing chain, which replicates and cancels the interference. The effectiveness of the proposed method has been verified using measurement data from real-world scenarios.
- 8 September 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 68 (3) , 923-927
A Robust Mixed-Signal Cancellation Approach for Even-Order Intermodulation Distortions in LTE-A/5G-Transceivers
State-of-the-art radio frequency receivers for mobile communications inevitably show nonlinearities, mainly caused by constraints in the analog design of the low-noise amplifier and the mixer. In the widely-used direct-conversion architecture, especially even-order intermodulation products cause interference in the baseband, thereby severely deteriorating the receiver signal-to-noise ratio. While several proposed methods aim to cancel second-order distortions caused by transmitter self-interference, the mitigation of higher-order effects is rarely covered. In this work, we present a novel scalable mixed-signal approach for cancellation of intermodulation distortions up to the sixth order. The interference signal is captured by means of an auxiliary receiver, which also allows to suppress interferences caused by external sources. The auxiliary receive signal serves as a basis for a real-time capable digital processing chain, which replicates and cancels the interference. The effectiveness of the proposed method has been verified using measurement data from real-world scenarios.
- 30 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Letters
- Vol. 3, 33
Corrections for “A Mixed-Signal Circuit Technique for Cancellation of Multiple Modulated Spurs in 4G/5G Carrier Aggregation Transceivers” [Nov 19 260-263]
In [1] , the description of Fig. 8 incorrectly presents the line plots in relation to the legend entries. The correct Fig. 8 and caption are presented here.
- 30 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Letters
- Vol. 3, 33
Corrections for “A Mixed-Signal Circuit Technique for Cancellation of Multiple Modulated Spurs in 4G/5G Carrier Aggregation Transceivers” [Nov 19 260-263]
In [1] , the description of Fig. 8 incorrectly presents the line plots in relation to the legend entries. The correct Fig. 8 and caption are presented here.
- Open Access
- 27 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 67 (7) , 1229-1233
A Harmonic Rejection Strategy for 25% Duty-Cycle IQ-Mixers Using Digital-to-Time Converters
Due to the use of wide-band analog front-ends in order to cover the many different frequency bands used in Long Term Evolution (LTE), blocker signals received by the antenna may reach the mixer input. As a consequence, squarewave mixer implementations, as e.g. the 25% duty-cycle currentdriven passive mixer, may lead to the down-conversion of these blocker signals by their harmonic response. This contribution describes a harmonic rejection (HR) strategy, which modifies the local oscillator (LO) waveform of a 25% duty-cycle currentdriven passive mixer, to suppress specific harmonics. Two HR control signal waveforms are proposed and their performance is evaluated by circuit simulations using a 28nm CMOS technology. By applying the proposed concept, the down-conversion of a blocker by the mixer’s 3rd order harmonic response can be suppressed by more than 30 dB, and the receiver noise figure (NF) is improved by 21.1 dB for a blocker power of -5dBm at the low-noise amplifier (LNA) input.
- 27 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 67 (7) , 1229-1233
Open AccessA Harmonic Rejection Strategy for 25% Duty-Cycle IQ-Mixers Using Digital-to-Time Converters
Due to the use of wide-band analog front-ends in order to cover the many different frequency bands used in Long Term Evolution (LTE), blocker signals received by the antenna may reach the mixer input. As a consequence, squarewave mixer implementations, as e.g. the 25% duty-cycle currentdriven passive mixer, may lead to the down-conversion of these blocker signals by their harmonic response. This contribution describes a harmonic rejection (HR) strategy, which modifies the local oscillator (LO) waveform of a 25% duty-cycle currentdriven passive mixer, to suppress specific harmonics. Two HR control signal waveforms are proposed and their performance is evaluated by circuit simulations using a 28nm CMOS technology. By applying the proposed concept, the down-conversion of a blocker by the mixer’s 3rd order harmonic response can be suppressed by more than 30 dB, and the receiver noise figure (NF) is improved by 21.1 dB for a blocker power of -5dBm at the low-noise amplifier (LNA) input.
- Open Access
- 16 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Letters
- Vol. 2 (11) , 260-263
A Mixed-Signal Circuit Technique for Cancellation of Multiple Modulated Spurs in 4G/5G Carrier Aggregation Transceivers
In carrier-aggregation 4G/5G transceivers LO spurs are generated which may down-convert any interferer located at the spurious frequencies. A mixed-signal circuit re-creates the spur building laws by multi-phase mixing and provides replica of multiple blocker-induced distortions without prior knowledge of their carrier frequencies. This technique, implemented in 28 CMOS, can cancel multiple spurious receive products by up to 33 for blocker power levels of up to -10 at the LNA input.
- 16 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Letters
- Vol. 2 (11) , 260-263
Open AccessA Mixed-Signal Circuit Technique for Cancellation of Multiple Modulated Spurs in 4G/5G Carrier Aggregation Transceivers
In carrier-aggregation 4G/5G transceivers LO spurs are generated which may down-convert any interferer located at the spurious frequencies. A mixed-signal circuit re-creates the spur building laws by multi-phase mixing and provides replica of multiple blocker-induced distortions without prior knowledge of their carrier frequencies. This technique, implemented in 28 CMOS, can cancel multiple spurious receive products by up to 33 for blocker power levels of up to -10 at the LNA input.
- Open Access
- 4 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 66 (9) , 3517-3530
Ultra-Low Complex Blind I/Q-Imbalance Compensation
Direct-conversion transceivers are the predominating architecture in current mobile communication systems. Despite many advantages, this topology suffers from unavoidable mismatches in the analog part, which causes imbalance between the in-phase and quadrature (I/Q) component. In this paper, we present a novel fully digital, blind I/Q imbalance compensation algorithm that features extremely low computational complexity and high compensation performance for a wide range of input signal types. Different to many state-of-the-art compensation schemes, the approach is not based on a gradient descent optimization and does not require any global feedback. This simplifies the implementation at high data rates and reduces the configuration effort to a minimum. For comparison, we examine an existing method of moment-based estimator with similar properties, for which we also provide the detailed insights beyond available literature. For both algorithms, we provide a rigorous mathematical analysis, which is supported by simulations with a focus on various long-term evolution (LTE) signal types. In addition, hardware architectures, including field-programmable gate array (FPGA) verification, are presented for both algorithms.
- 4 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 66 (9) , 3517-3530
Open AccessUltra-Low Complex Blind I/Q-Imbalance Compensation
Direct-conversion transceivers are the predominating architecture in current mobile communication systems. Despite many advantages, this topology suffers from unavoidable mismatches in the analog part, which causes imbalance between the in-phase and quadrature (I/Q) component. In this paper, we present a novel fully digital, blind I/Q imbalance compensation algorithm that features extremely low computational complexity and high compensation performance for a wide range of input signal types. Different to many state-of-the-art compensation schemes, the approach is not based on a gradient descent optimization and does not require any global feedback. This simplifies the implementation at high data rates and reduces the configuration effort to a minimum. For comparison, we examine an existing method of moment-based estimator with similar properties, for which we also provide the detailed insights beyond available literature. For both algorithms, we provide a rigorous mathematical analysis, which is supported by simulations with a focus on various long-term evolution (LTE) signal types. In addition, hardware architectures, including field-programmable gate array (FPGA) verification, are presented for both algorithms.
- Open Access
- 6 September 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 65 (11) , 3745-3755
A Mixed-Signal Circuit Technique for Cancellation of Interferers Modulated by LO Phase-Noise in 4G/5G CA Transceivers
In RF transceivers operating in carrier-aggregation, spurs are generated on the transceiver chip which may down-convert any blocker signal located at the spur frequency into the receiver baseband. The blocker signal could either be the transceiver's own transmit signal when operating in frequency-division duplex, or a WiFi-related signal received by the antenna. This so-called modulated spur interference contains the phase-noise (PN) of the involved local oscillator harmonics which created the spur and leads to a degradation of the wanted RX signal. The presented mixed-signal circuit mimics the spur building law including the PN of the harmonics and is, therefore, able to provide a replica of the spur interference including PN modulated components. This replica is then used as a reference signal for the digital cancellation of the main and image modulated spur interference using a widely-linear (WL) cancellation structure. The proposed circuit technique is implemented in 28 nm LP CMOS technology, and measurement results show that the mixed-signal solution outperforms a digital-only WL cancellation with respect to PN cancellation even with high blocker power levels of -15 dBm at the input of the low-noise amplifier.
- 6 September 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 65 (11) , 3745-3755
Open AccessA Mixed-Signal Circuit Technique for Cancellation of Interferers Modulated by LO Phase-Noise in 4G/5G CA Transceivers
In RF transceivers operating in carrier-aggregation, spurs are generated on the transceiver chip which may down-convert any blocker signal located at the spur frequency into the receiver baseband. The blocker signal could either be the transceiver's own transmit signal when operating in frequency-division duplex, or a WiFi-related signal received by the antenna. This so-called modulated spur interference contains the phase-noise (PN) of the involved local oscillator harmonics which created the spur and leads to a degradation of the wanted RX signal. The presented mixed-signal circuit mimics the spur building law including the PN of the harmonics and is, therefore, able to provide a replica of the spur interference including PN modulated components. This replica is then used as a reference signal for the digital cancellation of the main and image modulated spur interference using a widely-linear (WL) cancellation structure. The proposed circuit technique is implemented in 28 nm LP CMOS technology, and measurement results show that the mixed-signal solution outperforms a digital-only WL cancellation with respect to PN cancellation even with high blocker power levels of -15 dBm at the input of the low-noise amplifier.
- Open Access
- 10 January 2018
- Published by Springer Nature in e+i Elektrotechnik und Informationstechnik
- Vol. 135 (1) , 76-82
From microwatt to gigabit: challenges of modern radio design
- 10 January 2018
- Published by Springer Nature in e+i Elektrotechnik und Informationstechnik
- Vol. 135 (1) , 76-82
Open AccessFrom microwatt to gigabit: challenges of modern radio design
- 1 October 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 23-28
A Circuit Technique for Blocker-Induced Modulated Spur Cancellation in 4G LTE Carrier Aggregation Transceivers
In this paper, we propose a novel mixed-signal cancellation circuit for LTE carrier aggregation receivers targeting modulated spur interference. This circuit senses interference via an auxiliary analog path, and generates a reference signal for the adaptive digital cancellation. To evaluate the performance of the proposed technique, a demonstrator, realized in 28 nm LP CMOS, is shown with a cancellation of over 20dB and low impact on the main path while consuming 14.3 mW. Measurement results show that the receiver's noise figure is restored to a value within 0.1 dB of the reference value.
- 1 October 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 23-28
A Circuit Technique for Blocker-Induced Modulated Spur Cancellation in 4G LTE Carrier Aggregation Transceivers
In this paper, we propose a novel mixed-signal cancellation circuit for LTE carrier aggregation receivers targeting modulated spur interference. This circuit senses interference via an auxiliary analog path, and generates a reference signal for the adaptive digital cancellation. To evaluate the performance of the proposed technique, a demonstrator, realized in 28 nm LP CMOS, is shown with a cancellation of over 20dB and low impact on the main path while consuming 14.3 mW. Measurement results show that the receiver's noise figure is restored to a value within 0.1 dB of the reference value.