MKMohamed Omar Kayed

Mohamed Omar Kayed

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Mohamed Omar Kayed has a total of 9 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Development of MEMS-based piezoresistive 3D stress/strain sensor using strain technology and smart temperature compensation

    by Mohammed O Kayed, Amr A Balbola, Edmond Lou, Walied A Moussa

    This paper presents the microfabrication and testing of a membrane-free eight-element single-polarity (n-type) sensing rosette integrated with strained silicon technology over (111) silicon plane to measure the full 3D stress/strain tensor with full temperature compensation. Such n-type piezoresistive (PR) sensor has low sensitivity to the out-of-plane components compared to the in-plane components. To improve the sensitivity of such sensors to the out-of-plane components, a strained silicon technique was integrated into the sensing rosette during the microfabrication process using a highly compressive film produced by plasma enhanced chemical vapor deposition silicon nitride. For experimental verification, a prototype device featuring the proposed sensing rosette was microfabricated using semiconductors fabrication processes. The experimental analysis applied both, in-plane and out-of-plane stresses at different temperatures over a range from −20 °С to 60 °С. In this work, a smart sensing calibration algorithm, utilizing machine learning, is employed to reduce the temperature impact on both sensitivity and resistance of PR coefficients during stress measurement. The developed sensor is capable of accurately extracting the applied stress/strain components with temperature compensation.


  • Testing of a Strained Silicon Based 3-D Stress Sensor for Out-of-Plane Stress Measurements

    by Amr Adel Balbola, Mohamed Omar Kayed, Edmond Lou, Walied A. Moussa

    A new 3D stress sensor that features strain engineering is developed with the capability of extracting the six stress components in a full temperature compensation manner. This paper presents the detailed testing of the out-of-plane shear and normal stress for the developed chip. The shear state is produced via applying horizontal force on a micro-fabricated two-point shear bridge structure, which is mounted on a chip on a printed circuit board (PCB). On the other side, a direct vertical force is utilized to induce normal stress directly at the sensing rosette. Finite element analysis is conducted for both loading cases to evaluate the level and uniformity of these stress components. The tested chip captures the out-of-plane shear and normal stress with 16% and 11% full scale (FS) error, respectively


  • Development of a Self-Monitored 3D Stress Sensor for Adhesive Degradation Detection in Multilayer Assemblies

    by Amr A. Balbola, Mohammed O. Kayed, Edmond Lou, Walied A. Moussa

    In this paper, a novel technique is proposed to provide a 3D piezoresistive MEMS stress sensor with a real-time self-monitoring of its bonding status. Perceiving the degradation of this interlayer due to different environmental parameters is crucial for reliable electronics and sensors assembly. The utilized sensor is featuring strain technology to fully extract the six stress components. Whenever a multilayer assembly, such as a sensor on a structure, is subjected to thermal or mechanical load, out-of-plane shear stress will accumulate at its edge as a reaction for peeling. As any degradation in the adhesion layer causes a significant reduction for out-of-plane shear stress, the capability of the 3D chip to measure this stress is employed to detect the degradation of the adhesive layer. To verify the capability of the current concept to experimentally quantify this loss, thermal energy is exploited for softening the bonding film. Losses up to 28 % for the out-of-plane shear stress are detected at a temperature equal to 80°c, which causes 71.9 percent decrease in the modulus of elasticity of the utilized adhesive. This significant correlation, between the out-of-plane shear stress loss and the bonding layer stiffness, is used to obtain a full picture of the adhesive deterioration in an early phase. The same technique can be utilized as a low profile detector for the debonding in multilayer electronics.


  • Hybrid Smart Temperature Compensation System for Piezoresistive 3D Stress Sensors

    by Mohammed O. Kayed, Amr A. Balbola, Edmond Lou, Walied A. Moussa

    This paper proposes a new hybrid temperature compensation system for doped silicon-based piezoresistive 3D stress sensors. The developed compensation system integrates a temperature sensor, placed in close proximity to the stress sensing rosettes, with the artificial neural networks (ANNs). In this work, the n-type circular piezoresistor featured over (111) silicon plane was employed to capture the local temperature variations, within the sensing chip. The extracted temperature changes, along with the resistance changes, are fed, as inputs, to the ANNs to compensate the temperature effect on the acquired signals for more accurate stress measurement. The proposed compensation system was experimentally evaluated while extracting stress applied up to 60 MPa at different temperatures within a range from 0 °C. to 50 °C. The developed system was successfully able reduce the maximum full scale error, obtained from using only a temperature sensor for compensation, by ~55%. The new system has merit since it has the capability to compensate for both resistance and sensitivity, for 3D stress sensor, with no need for additional circuitry. Moreover the employed temperature sensor shares the same thermal environment with the stress sensing rosette.


  • A New Approach for Developing a 3-D Stress Sensing Rosette Featuring Strain Engineering

    by Amr A. Balbola, Mohammed O. Kayed, Edmond Lou, Walied A. Moussa

    Stress transducers play essential roles in diagnostic testing, monitoring, and nondestructive evaluation of many infrastructures. Particularly, 3-D piezoresistive (PR)-based stress sensors would tool up these applications with a high gauge sensing platform. In this article, strain engineering is utilized to develop a 3-D stress sensor where the microfabrication complexity and cost are reduced. Three types of prestrain are exploited for generating three different groups of PR coefficients; thus, a set of linear independent equations is obtained. The independency of these generated equations is verified both analytically and experimentally. A four-point testing is conducted on both chip wafer and flip chip on printed circuit board (PCB) structure to assess experimentally the capability of the strain approach to build a 3-D single polarity rosette. Both the analytical and experimental evaluations show the ability of the developed chip to extract the six stress components in a fully temperature compensation manner.


  • A New Temperature Transducer for Local Temperature Compensation for Piezoresistive 3-D Stress Sensors

    by Mohamed Omar Kayed, Amr Adel Balbola, Walied A. Moussa

    In this paper, a new temperature transducer using full-circular n-type piezoresistor over (111) silicon plane is proposed as an accurate solution for local temperature compensation for piezoresistive 3D stress sensors. Analytical study, in the current work, showed that the proposed n-type full-circular piezoresisor over (111) has near-zero response under 3D state of stress. As an experimental verification, a test device with n-type piezoresistive stress sensing elements oriented over (111) plane at 0° and 90° to crystallographic direction [110] was microfabricated to test the capability of the proposed temperature compensator. The test device was subjected to a uniaxial load up to 50 MPa using a loading rig with four-point bending fixture. The testing was performed over a temperature range of 0-50 °C. The results showed that the proposed temperature transducer has a linear response to temperature excitation. The fabricated transducer is capable of accurately capturing the local temperature changes with maximum absolute error of $\pm$ 0.8 °C. This compensation system is advantageous for piezoresistive stress/strain sensors, since the temperature transducer has the same thermal environment with the stress/strain sensing rosette. Moreover, this technique does not require additional circuitry on the sensing device itself.


  • Experimental Characterization of the Influence of Transverse Prestrain on the Piezoresistive Coefficients of Heavily Doped n-Type Silicon

    by Amr A. Balbola, Mohammed O. Kayed, Walied A. Moussa

    Strain has been integrated into many silicon devices, as it has an essential impact on carrier mobility and crystal symmetry. Those parameters respond differently under both biaxial and uniaxial, so their effect needs to be quantified to successfully employ the strain engineering in different silicon applications. As an extended step toward utilizing strain in enhancing the sensitivity and the temperature independency of a 3-D stress sensor, the effect of uniaxial transverse strain onto the piezoresistive (PR) coefficients of heavily doped n-type silicon will be experimentally characterized. A new design was developed to apply the transverse tensile and compressive uniaxial stresses onto the silicon substrate using a highly compressive nitride layer. This stressing technique was integrated with six PR elements rosette to fully calibrate the PR coefficients, where unstrained, tensile, and compressive strained PRs are fabricated within the same chip to accurately quantify the strain impact. Four-point bending, stress-free temperature, and hydrostatic test were used to typically measure the PR coefficients. Strain values of 0.065% and 0.083% $\varepsilon $ were achieved locally using both the tensile and compressive stressors, respectively. Under this level of strain, the typical result shows opposite impact for both the tensile and compressive transverse strains on the longitudinal and transverse PR coefficients. Moreover, an increase up to 80% can be achieved for the pressure coefficient of heavily doped n-type silicon due to the compressive transverse strain.


  • On the Feasibility of a New Technique for Applying and Sensing a Pre-Strain State for Strain Engineering

    by Amr A. Balbola, Mohammed O. Kayed, Walied A. Moussa

    This paper reports a successful design, fabrication, and characterization of a new microstructure, that utilizes piezoresistivity, for locally applying a pre-strain state onto silicon substrates and measuring it. This technique allows for applying tensile and compressive transverse local strain for the first time, using the same stressing layer rather than using nitride capping for tensile or silicon germanium for compressive strain. It is well-known that the only strain that enhances both electron and hole mobility simultaneously is the transverse uniaxial strain. Moreover, the utilized sensing structure evaluates directly the actual stress transmitted to the substrate. Therefore, it is a valuable tool for strain engineering applications, where modulating and determining the pre-strain state onto the silicon at infinitesimal areas are required. The proposed structure composed of highly compressive plasma enhanced chemical deposition nitride layer that was patterned in a way allowing for inducing both local tensile and compressive uniaxial pre-strain onto the silicon. Using this method, the stress transferred to silicon is around 40 to 150 MPa, however the developed sensing structure was capable of detecting it for both tensile and compressive stresses.


  • Studying the Effect of N-Type Strained Silicon on the Temperature Coefficient of Resistance

    by Amr A. Balbola, Mohammed O. Kayed, Walied A. Moussa

    As a step in employing the strained silicon in enhancing a MEMS piezoresistive based 3D stress sensor performance, this paper studies the influence of pre-stretching silicon atoms on the temperature coefficient of resistance (TCR). Extracting accurately the TCR is very influential for the piezoresistive based stress sensor. For this purpose, a piezoresistive sensing rosette was fabricated on strained and unstrained silicon substrates. The pre-strained state was integrated during microfabrication using an intrinsic stress produced by highly compressive plasma enhanced chemical vapor deposition (PECVD) silicon nitride layer, which induces global biaxial tensile pre-strain onto the substrate. Under a stress free thermal loading, the TCR for both strained and unstrained chips were calibrated using an environmental chamber. Comparing the calibration results in both strained and unstrained silicon, the tensile pre-strained silicon has larger TCR than that in unstrained silicon. Moreover, over the surface concentration range used in this work, the strained silicon shows the same unstrained silicon trend, which is, the TCR is increased proportionally with the surface concentration.